Woodworking_Hobby Posted March 19, 2025 Report Posted March 19, 2025 Tonight was supposed to be an easy night in the shop and I was trying to finish a few small projects I started a long time ago. I am not sure what happened, but I feel like I was fighting the projects every step of the way tonight. Usually I am working with cherry and was using hard maple and Purple Heart, so not sure if the harder woods were compounding anything or if it was just that kind of night. I did have two questions that came up in the work; sorry for the two setup questions…I feel like I have had a lot of random little questions lately, but this group always is the best resource I have! Table Saw Fence: I have an incra fence on my table saw and when I installed the fence the instructions had you tilt the top a hair away from the blade. Usually I am rippinng 3/4 inch boards for my projects, but tonight I was ripping 1 3/4 inch thick boards. I also set a feather board in front of the blade to keep pressure on the board against the fence. Tonight I noticed since the fence has that slight tilt if you are not very careful and put too much side pressure to high on the side of the board, it will tip and that could affect the rip being square. Is this correct for the fence and just something that will impact ripping the thicker stock? I have not noticed this being an issue in my typical work when I am ripping boards around 3/4 inch thick. Jointer fence: I feel like I am always chasing getting my jointer fence set at 90 degrees to the bed when I am cleaning up one edge to the face. No matter how well I set the fence it never seems to be quite square or seems ok but hard to tell exactly. Recently what I have been doing is milling the two faces of the board to get them parallel and coplanar. Then I joint one edge on the jointer and check it with my square to get it as close as I can to 90 degrees to the face. I feel like for thinner boards I can get it pretty good and struggle a little with thicker boards. What I have done to help is I keep my boards a little wider than needed for final dimensions. After I joint the edge to one face, I use the table saw to rip the opposite edge from what I just passed through jointer. Then I flip the board to cut off the jointed edge to get down to final dimensions. I feel like this helps get both sides square by using the table saw on both edges to get to final dimensions since I have a little better control on the table saw to get the blade to 90 than what I feel I can do to adjust the jointer fence. Short of the long, I am just wondering if there are any tips or tricks to get the fence on the jointer any closer to 90 or am I just stuck until someday I am able to maybe upgrade that tool, which is not very high on the list. Also do you see any issues with using the table saw on both edges of the board and removing the edge that was jointed? I can also get a cleaner edge on the table saw and it removes some of the “scalloping” I can get on the jointer. 1 Quote
Popular Post wtnhighlander Posted March 19, 2025 Popular Post Report Posted March 19, 2025 I have always tried to keep my TS fence as square (perpendicular) to the table as possible. I suppose tilting slightly away from the blade is better than tilting toward it. I also used your method of ripping both edges after jointing one, when I was using a small jointer with a not so stable fence. I gave it up, and joint edges by hand now. Slower, but far better quality than the crappy jointer provided. 3 Quote
Von Posted March 19, 2025 Report Posted March 19, 2025 On 3/19/2025 at 6:38 AM, wtnhighlander said: I have always tried to keep my TS fence as square (perpendicular) to the table as possible. I suppose tilting slightly away from the blade is better than tilting toward it. +1 On 3/19/2025 at 12:24 AM, Woodworking_Hobby said: Short of the long, I am just wondering if there are any tips or tricks to get the fence on the jointer any closer to 90 or am I just stuck until someday I am able to maybe upgrade that tool, which is not very high on the list. Also do you see any issues with using the table saw on both edges of the board and removing the edge that was jointed? I can also get a cleaner edge on the table saw and it removes some of the “scalloping” I can get on the jointer. If you are jointing the edges to make a panel, you can alternate them on the jointer so they end up complementary and flat. In other words, put the top against the fence for one and then the bottom for the other - they will both be a little off 90, but when put together should be produce a tight, flat joint. 2 Quote
legenddc Posted March 19, 2025 Report Posted March 19, 2025 First of all, I hate those nights. That's usually when I pack it in and come back the next day. On 3/19/2025 at 12:24 AM, Woodworking_Hobby said: I have an incra fence on my table saw and when I installed the fence the instructions had you tilt the top a hair away from the blade. Do you mean the table saw fence isn't 90* to the table saw or the fence isn't parallel to the blade and the back is angled away from the blade? If the fence isn't 90* to the table saw body (not blade), I would adjust it and test it. On 3/19/2025 at 12:24 AM, Woodworking_Hobby said: Then I joint one edge on the jointer and check it with my square to get it as close as I can to 90 degrees to the face. I feel like for thinner boards I can get it pretty good and struggle a little with thicker boards. I'm by no means an expert on jointer setup. Have you tried moving the fence forward and jointer the boards on the edge? I'm wondering if your jointer blades aren't parallel to the bed and you don't realize it on thinner boards. Is your square actually square? 2 Quote
Popular Post Mark J Posted March 19, 2025 Popular Post Report Posted March 19, 2025 Your questions are welcome. (Sometimes pictures of what you are talking about can make the issue clearer). It might be helpful to know what make and model of jointer you're using. Someone may know of a particular quirk or trick. And let me ask what measuring tool you are using to set your jointer fence? It may be the culprit. If you are using a typical big box square, these can be off a half or whole degree, which may be fine for rough carpentry, but will matter in joinery. As to the "tilted tablesaw fence", I've never heard of doing that, but it reduce the chance of kickback. I think you are right, though. you want the ginger board close to the table top and pushing against the base of the fence. 3 Quote
Woodworking_Hobby Posted March 19, 2025 Author Report Posted March 19, 2025 Thanks all for the tips; I am going to read through them all again this evening and try to take some time to go look at my setup. I will post back with what I find or if I have an additional question. I did learn one thing last night though, I need to stop being lazy and put my ripping blade on the saw when I am doing thicker cuts and for most ripping. I was using my 30 tooth rip blade last night and it cut so much better than the 40 tooth combo blade. Yes the combo will rip and will get ok results but with the ripping blade it just cut so much easier, way less burning, way less pressure required, and way less noise and power draw. It was interesting how the ripping blade just “sounds” different on the saw when it’s running under no load. I think going forward I am going to try and use that blade more when I am ripping my parts down to final widths. 2 Quote
legenddc Posted March 19, 2025 Report Posted March 19, 2025 Do you have a Forrest Woodworker II 40T blade? I've noticed when I put any other blade on the saw sounds a lot different. Quote
Woodworking_Hobby Posted March 19, 2025 Author Report Posted March 19, 2025 17 minutes ago, legenddc said: Do you have a Forrest Woodworker II 40T blade? I've noticed when I put any other blade on the saw sounds a lot different. I do; usually I just keep the 40 tooth WWII on the saw but since I was going to rip thick wood I put in a 30 tooth WWII ripping blade. The 30 tooth sounds way different than the 40 tooth. 1 Quote
Woodworking_Hobby Posted March 19, 2025 Author Report Posted March 19, 2025 7 hours ago, Mark J said: As to the "tilted tablesaw fence", I've never heard of doing that, but it reduce the chance of kickback. I think you are right, though. you want the ginger board close to the table top and pushing against the base of the fence. On the fence by luck I had saved the email I got from Incra a while ago. ——- – Setting the fence anywhere between perfectly square and leaning back slightly is fine… I set my fences to lean back very slightly, about the thickness of a sheet of paper between the square and the top edge of the fence. —— I think I got either a little aggressive with the thickness of a sheet of paper or it has moved over time. I checked this afternoon and it tilts back a few degrees at the top so a little more than it should. I am going to try and remove some of the tape I added to shim the top and bring it back closer to 90. I remember the slight gap was to help prevent kickback but it was supposed to be tiny. 1 Quote
Popular Post Tom King Posted March 19, 2025 Popular Post Report Posted March 19, 2025 I have always had my fence dead on square and wouldn't want it any other way. It's good to have a machinist square to check things like jointer fences. There are some available that aren't too expensive and plenty good enough. 4 1 Quote
Woodworking_Hobby Posted March 20, 2025 Author Report Posted March 20, 2025 17 hours ago, Tom King said: I have always had my fence dead on square and wouldn't want it any other way. It's good to have a machinist square to check things like jointer fences. There are some available that aren't too expensive and plenty good enough. I squared up the fence to the table last night. Took a few strips of tape and used those as shims and now it is 90 to the table. I have a few good combination squares I use and for my birthday someone got me a DelVe square and I use that to setup my tools. I also get a set of machine squares for Christmas; I think they are a shop fox set but have not checked them yet. TBH they are coated in antitrust and I have not taken them time to clean them yet. Any tricks the then check the fence being parallel to the blade? I used my straight edge and checked front of blade and back of blade distance from the fence and they were both right at 1 inch as best as my eye could see. I ripped a cut piece and it seemed to cut ok and it was one inch wide across the entire length. Quote
Mark J Posted March 20, 2025 Report Posted March 20, 2025 27 minutes ago, Woodworking_Hobby said: I squared up the fence to the table last night. Took a few strips of tape and used those as shims and now it is 90 to the table. I have a few good combination squares I use and for my birthday someone got me a DelVe square and I use that to setup my tools. I also get a set of machine squares for Christmas; I think they are a shop fox set but have not checked them yet. TBH they are coated in antitrust and I have not taken them time to clean them yet. Any tricks the then check the fence being parallel to the blade? I used my straight edge and checked front of blade and back of blade distance from the fence and they were both right at 1 inch as best as my eye could see. I ripped a cut piece and it seemed to cut ok and it was one inch wide across the entire length. It seems you have one problem solved. That leaves the jointer. Is that fence square at multiple points on both infeed and out feed sides? Are you blades parallel to the infeed and outfeed tables? Is the fence square to the bed both before and after a jointing operation (I'm thinking loose fence here)? Are the beds and fence surfaces actually flat when evaluated with a known straight edge? As they say, just spitballing here. It looks like the DelVe square is a Woodpeckers' product. If so, then you can rely on it with confidence. If you have the 3.5" model that may be smallish for some of the tasks (but then 6" sometimes can be biggish). The Shop Fox machinist set is probably good as well (the fact that they bothered to cover them in cosmoline suggests that someone thought they were good enough to need protection) . Compare them against the Woodpeckers, if they are also 90, then you may have some different sizes for different applications. Quote
Popular Post wtnhighlander Posted March 21, 2025 Popular Post Report Posted March 21, 2025 Referring back to the tablesaw for a moment. Aligning the fence to the blade really means aligning it to the miter gauge slot. An inexpensive dial indicator is worth the investment for this. Attach it to a block of wood that can slide in the slot and check the fence from end to end. Then the blade must align to the slot as well. How you adjust that depends on the saw. Contractor saws usually have the arbor raise / tilt mechanism attached to the underside of the table, and adjustment may require working from below, maybe removing the 'box' portion to gain access. Cabinet saws are more likely to have the mechanism suspended from the cabinet walls, and the table is adjusted by loosening the bolts that hold it to the cabinet. I'm with Tom, and prefer everyting truly square, but some folks suggest having the far end of the fence aiming away from the blade by a couple thou, to help avoid binding & kickback. Until you need to cut with the fence on the opposite side of the blade... 4 1 Quote
Popular Post roughsawn Posted March 21, 2025 Popular Post Report Posted March 21, 2025 On 3/20/2025 at 11:52 AM, Woodworking_Hobby said: Any tricks the then check the fence being parallel to the blade? I used my straight edge and checked front of blade and back of blade distance from the fence and they were both right at 1 inch as best as my eye could see. I ripped a cut piece and it seemed to cut ok and it was one inch wide across the entire length. https://www.amazon.com/Neoteck-Indicator-Calibrating-Machinery-Press-Black/dp/B0D22CS814/ref=sr_1_8?crid=26BM7DYS76KAE&dib=eyJ2IjoiMSJ9.4e-_KE2H12qzNCSOMdhdxtkx8JWyO_C2pfCDBEv0-4BhWlufLKlX_3Sd_yje6uTnGYYRAZUPCWTsl-O_GjAJusBGx-LI-JprVKztRU2-PPke5qOmAHGRVZvM9Fg1nPpkZRdZw1KgM0yfAxF9OR6-bXmmuG2HMsAM3ts3yd0q6RTQbKtdh8bQd2oOwodeoXEKFSt3NHt9oZd7DbIimBlN6qgyf9OydvPc6GH21DRB4rKXBNYtBwviuzMY4wyUQoDtRoSPHW6KRR9et1SgAvYJdVfaUCbgHBulO-_TDIb2GJlJRI9OaV92s84aMSAjTtJVTKRGAkjPxiRoyCqPX_QwgyQOKbChC03t4Sp8M7GmQ4QCHQiO_yw5MsmnrBAkJ_uWD7mYetTpPz-5DVzaR8iugpWI-a1nSCvNXjAjeuW45rvschUiDjPflVx0-KaaZcRC.qjE8z0bNRg_Z1ruu2gXh-YwUmK6Lw-iYRmzjKbEB_uk&dib_tag=se&keywords=neotec+table+saw+gauge&qid=1742523903&sprefix=neotec+table+saw+gauge%2Caps%2C196&sr=8-8 Wow, that is a long link! 2 1 Quote
Woodworking_Hobby Posted March 21, 2025 Author Report Posted March 21, 2025 15 hours ago, wtnhighlander said: Referring back to the tablesaw for a moment. Aligning the fence to the blade really means aligning it to the miter gauge slot. An inexpensive dial indicator is worth the investment for this. Attach it to a block of wood that can slide in the slot and check the fence from end to end. Then the blade must align to the slot as well. How you adjust that depends on the saw. Contractor saws usually have the arbor raise / tilt mechanism attached to the underside of the table, and adjustment may require working from below, maybe removing the 'box' portion to gain access. Cabinet saws are more likely to have the mechanism suspended from the cabinet walls, and the table is adjusted by loosening the bolts that hold it to the cabinet. I'm with Tom, and prefer everyting truly square, but some folks suggest having the far end of the fence aiming away from the blade by a couple thou, to help avoid binding & kickback. Until you need to cut with the fence on the opposite side of the blade... I am assuming you want the blade aligned to the miter gauge so when you are crosscutting you get a true 90 degree cut and that is the most critical setting when adjusting. 1 Quote
legenddc Posted March 21, 2025 Report Posted March 21, 2025 On 3/21/2025 at 1:50 PM, Woodworking_Hobby said: I am assuming you want the blade aligned to the miter gauge so when you are crosscutting you get a true 90 degree cut and that is the most critical setting when adjusting. The calibrating tools like shared above reference the miter slot. You can use that tool to align the table saw fence to the miter slot and also use it to align the blade to the same miter slot. 1 1 Quote
Popular Post wtnhighlander Posted March 21, 2025 Popular Post Report Posted March 21, 2025 Yep. Aligning to the slot gives you straight rips and square cross-cuts. 2 1 Quote
Popular Post Botch Posted March 22, 2025 Popular Post Report Posted March 22, 2025 On 3/19/2025 at 5:41 PM, Tom King said: I have always had my fence dead on square and wouldn't want it any other way. It's good to have a machinist square to check things like jointer fences. There are some available that aren't too expensive and plenty good enough. To my machinist’s square I have added a small flashlight, to hold behind the square and shine the light against it; really helps my 65-yr old eyes. 3 1 Quote
Popular Post Botch Posted March 22, 2025 Popular Post Report Posted March 22, 2025 On 3/20/2025 at 8:08 PM, wtnhighlander said: …Then the blade must align to the slot as well. How you adjust that depends on the saw. Contractor saws usually have the arbor raise / tilt mechanism attached to the underside of the table, and adjustment may require working from below, maybe removing the 'box' portion to gain access. Cabinet saws are more likely to have the mechanism suspended from the cabinet walls, and the table is adjusted by loosening the bolts that hold it to the cabinet. I checked the alignment of my slots to the blade with a cheap method: set your miter gauge to 90º, then cut thru a 1/4” dowel. Holding tight, continue to move the dowel to the rear of the blade, and listen to the sound it makes as it passes the teeth. Then move the gauge to the slot on the other side of the blade, and repeat the process; the sound it makes as it passes the rear of the blade should be the same. I did this to my new tablesaw in ‘92, a Delta contractor’s saw. The dowel made a racket with one slot, and didn’t touch the blade with the other slot, so I had some adjusting to do. That was a miserable Saturday… 3 1 Quote
Popular Post roughsawn Posted March 22, 2025 Popular Post Report Posted March 22, 2025 That table saw gauge is the one I use. It really shows you some stuff. My TS fence has a couple little "waves" in it! And every TS blade I checked has .0015-.002 runout. Even my best Ridge Carbide. Makes me wonder just exactly how perfect alot of this stuff really has to be. I sleep better at night knowing that there is nothing I can do about these "unperfect" items/processes. 4 1 Quote
Coop Posted March 22, 2025 Report Posted March 22, 2025 On 3/21/2025 at 7:16 PM, Botch said: I checked the alignment of my slots to the blade with a cheap method: set your miter gauge to 90º, then cut thru a 1/4” dowel. Holding tight, continue to move the dowel to the rear of the blade, and listen to the sound it makes as it passes the teeth. Then move the gauge to the slot on the other side of the blade, and repeat the process; the sound it makes as it passes the rear of the blade should be the same. I did this to my new tablesaw in ‘92, a Delta contractor’s saw. The dowel made a racket with one slot, and didn’t touch the blade with the other slot, so I had some adjusting to do. That was a miserable Saturday… Cheap, non-high techey method. I like it! Quote
BillyJack Posted May 3, 2025 Report Posted May 3, 2025 I set the fence square tomtye blade. Many shops set it outward as a means not to jamp wood. This happens mainly in cabinet shops were sheet goods ar3 cut on a regular bases. I don’t know how you coukd be a furniture maker using tools all adjusted this way. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.