Popular Post gee-dub Posted July 2 Popular Post Report Posted July 2 So I was sanding on a drawer box at the edge sander. I had a pocket screw not fully seated and was rewarded with a spray of sparks racing down the 6" collection port at an alarming rate. I went out to the DC shed to make sure I wasn't lighting anything on fire. While prowling around I noticed one of the capacitor covers was half off (???). I got a step stool so I could reach the motor area and saw that a screw had vibrated loose and was laying on top of the blower. The cap wiring blade connectors were exposed and I'm thinking "none of this is good". The cap covers and attachment method are designed in such a way that the cover itself is flexed when screwed down acting like a lock washer. I have replaced caps on this motor over the years and I imagine I just didn't apply (Cousin Vinny Reference) "proper torque-age" at that time as the other cap cover was fine. At any rate, this is just a PSA to run a maintenance routine on your machines now and again, confirm fasteners are tight, hoses are in place, gears are clean and lubricated, belts are in good condition, etc. I routinely do this about once a year. Christmas is my trigger . . . LOML is thinking "oh, this would be nice for the baby", I am thinking "we're Christmas shopping; did I run my maintenance routine this year?". This experience brought into stark relief the fact that while I pay attention to many of my machines I apparently ignore the cyclone. . . "say it isn't so". Lesson learned so I thought I would share. 9 Quote
Popular Post Chet Posted July 2 Popular Post Report Posted July 2 So let me see if I understand this correctly, anytime I have sparks running though my dust collection I should stop and do shop maintenance. 1 5 Quote
gee-dub Posted July 3 Author Report Posted July 3 On 7/2/2026 at 12:02 PM, Chet said: So let me see if I understand this correctly, anytime I have sparks running though my dust collection I should stop and do shop maintenance. Lord, I hope not. I have trouble getting through a project as it is 1 Quote
Popular Post Don Z. Posted July 3 Popular Post Report Posted July 3 So, what you're saying is your torque wrench wasn't calibrated to be dead on balls accurate? 1 3 Quote
pkinneb Posted July 4 Report Posted July 4 I will be putting this on my list to check next time I'm in the shop, thanks! Quote
Tpt life Posted July 5 Report Posted July 5 Slightly off topic, and slightly on. I helped my middle change her oil Friday, and her drain plug was only finger tight. Took 1.5 quarts out of a 5 quart reservoir. My oldest helped her last time. I don’t think his “torque-age” is experienced enough. 2 2 Quote
Popular Post Tom King Posted July 5 Popular Post Report Posted July 5 I put a Fumoto valve on Pam's Subaru and I like it a lot. You stick a little hose on it to drain the oil and there is not a drop spilled anywhere, nor any oil on your hands. It's either open or closed-no in between. https://www.fumotousa.com/ The lever is not as easy to operate as it shows in that video. I need a pair of short needle nose pliers to pull the lever down, compress the die spring holding it in the closed position, and turn to open, but it's not difficult to operate and very secure when it's closed. I don't have one on my truck because the oil pan plug location is not protected at all. 3 Quote
Ron Swanson Jr. Posted July 5 Report Posted July 5 On 7/5/2026 at 8:29 AM, Tom King said: I put a Fumoto valve on Pam's Subaru and I like it a lot. You stick a little hose on it to drain the oil and there is not a drop spilled anywhere, nor any oil on your hands. It's either open or closed-no in between. https://www.fumotousa.com/ The lever is not as easy to operate as it shows in that video. I need a pair of short needle nose pliers to pull the lever down, compress the die spring holding it in the closed position, and turn to open, but it's not difficult to operate and very secure when it's closed. I don't have one on my truck because the oil pan plug location is not protected at all. I drive an f150 and while the plug can be opened and closed by hand, it's located behind a bar so the oil will never come out clean, it makes a big mess. They couldn't have designed it worse if they tried. 1 Quote
Chestnut Posted July 5 Report Posted July 5 On the topic of PSA maintenance take your filter stack off and blow it out. It's been a couple years for me. I used to clean mine every 6 months. Edit: check your dust bin I'd bet its close to full too . 2 Quote
Chestnut Posted July 6 Report Posted July 6 19 hours ago, Chestnut said: Edit: check your dust bin I'd bet its close to full too Yep just what i thought. 2 Quote
Popular Post drzaius Posted July 6 Popular Post Report Posted July 6 I put a heat detector in the lid of my dust bin, connected to a strobe/horn alarm in the shop. Should things get too warm, I'll know in a hurry. 5 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.