jmaichel Posted July 3, 2013 Report Posted July 3, 2013 I just finished my daughter Sophie's Steamer Trunk...well really a toy box for the first few years. I decided to hold off on making the lid for now mostly because she would not be able to open the lid herself and more importantly I considered it a safety hazard for her fingers. For me this project was a challenge, I had never used a bunch of the joinery or techniques that were used in the building of this trunk. It also gave me a chance so see how the work flow in my shop was and use a bunch of my new tools...all of them in fact. That was the one really cool thing about building this chest, I used every tool in my shop. The details: The chest is made out of Purple Heart and Cherry. The purple Heart was 4/4 material and the Cherry was 8/4 material that I resawed. The design is a frame and panel design based on the one Marc Built on his site a few years ago, which is based on the Rockler Steamer Trunk. The panels are floating panels and the legs are rabbeted and each piece has a 1/4" groove for the for the panels to float in. The faux straps are walnut and I decided to go with two instead of three strips. For the hardware I used the steamer trunk hardware that Rockler sells. For the finish I used Minwax Polycrylic water based finish and I sprayed it on using an LVLP gravity feed sprayer that I bought from Grizzly. I had never done frame and panel joinery before so there was a small learning curve. Having never used a dado stack before it took me a little longer than it normally should to set up for each cut. Any to be honest I was really nervous running the 36" long rail pieces across the dado stack fortunately I took my time and used The Magswitch dual roller guide to help keep the rails in place while going over the stack. Resawing was also something that I had never done before and there was plenty of it. I was mostly happy with the results but I did end up with some drift. My expectations were not to high for my little 14" Grizzly bandsaw but it was up for the task. I made sure I had it set up properly thanks to one Michael Fourtune's videos on the Fine Woodworking website. Once I resawed the lumber I was faced with another issue and that was now having to joint one face flat before sending through the planer. I ended up using double stick carpet tape and attaching it to a piece of plywood and running it across the jointer. This method was recommend by a couple people on this forum and I was very pleased with the results. I sprayed two coats of finish on the inside of the trunk prior to installing the bottom. There were a few mistakes that were made. First off I glued up the legs a lot earlier than I should have and this posed a few problems. The biggest problems is that I could not glue up each panel individually. The second and even bigger problem was that I could not cut the rabbet for the bottom in each panel individually and had to use router to route the rabbet. I have very little router experience and had never cut a rabbet like this before so I made a couple mistakes. Fortunately the mistake were on the bottom and covered up pretty well by the hardware. The rabbets on my legs were a little gappy so I had to fill them with a glue mixture that I made from purple heart sawdust and glue. I have never sprayed on a finish either and I have to tell you that the LVLP sprayer is probably the best $40 I have ever spent. The water based finish dried very quickly and I was able to finish the outside of the trunk in a day. I used a Festool S1000 abrasive pad between coats and a S2000 after the final coat. The finish turned out awesome, very happy with this finish! Final thoughts: I literally used every tool in my shop for this build and it gave me a good idea of how the functionality of my shop was. I was very pleased for the most part but there are a few concerns. I just recently added a new dust collector but I noticed dust collection on my table saw is very poor. This is not flaw with the collector but with the design of the contractor style table saw, one that I will be addressing in between builds. I also noticed that Purple Heart and other hardwoods may just be a little to hard for the tooling in my shop. I am going to stick with woods that are softer from now on and may only go as hard as maple for future projects. I really enjoyed this build and it was a very gratifying experience. I am probably only going to build a couple items for the shop in the next couple of months and enjoy the summer here in the Pacific Northwest, there will be plenty of shop time when the rain and cold start back up. Quote
TerryMcK Posted July 3, 2013 Report Posted July 3, 2013 Nice job James. Dust collection on table saws is never good. I improved mine by judicious use of duct tape around the shroud surrounding the blade under the table. There are loads of places where air (vacuum?) can leak inside the TS. Enjoy the summer it's a beautiful part of the world. We visited a few years back and loved it. Quote
..Kev Posted July 3, 2013 Report Posted July 3, 2013 Great job James, I'm sure that will hold up for many years for her. Quote
rodger. Posted July 3, 2013 Report Posted July 3, 2013 Nice work, I like your choice of lumber. Quote
woodieboy Posted July 3, 2013 Report Posted July 3, 2013 That's a really great work! Nice wood choice. Quote
Darren66 Posted July 3, 2013 Report Posted July 3, 2013 James, great idea and looks really good. Also liked the description of the build. Quote
wdwerker Posted July 4, 2013 Report Posted July 4, 2013 Looks Great! Paduc also goes well with purple heart. Sunlight , time and oxygen will turn purple heart darker and kinda greyish brown. I visited the Pacfic Northwest once and I could see my breath on an August morning , must be a short summer up there. We are still sweating at the end of September here in Atlanta! Quote
jmaichel Posted July 5, 2013 Author Report Posted July 5, 2013 Thanks everyone for the nice comments. Steve- summers here are pretty short but they are very very nice. I hate to waste precious sunshine with shop time however shop time is never a waste, maybe I will just open the garage door Quote
mcatal01 Posted July 21, 2013 Report Posted July 21, 2013 Very nice, great contrast with the different timbers! Quote
TRBaker Posted July 21, 2013 Report Posted July 21, 2013 Great job, James. Keep it up. Btw, purple heart is too hard for the tooling in anyone's shop. You just have to plan on sending all your blades to a sharpener afterwards. Quote
lonestarwood Posted July 31, 2013 Report Posted July 31, 2013 Great job on that. Love the contrasts. Love the choice on the joinery. Quote
jmaichel Posted October 8, 2013 Author Report Posted October 8, 2013 Well, I finally finished the lid and all the hardware install! Quote
G S Haydon Posted October 8, 2013 Report Posted October 8, 2013 Very nicely executed James. The quality is very very good indeed, hope your feeling good about it Quote
jmaichel Posted October 8, 2013 Author Report Posted October 8, 2013 Very nicely executed James. The quality is very very good indeed, hope your feeling good about it Thanks Graham! I do feel good about it. It's the first piece that I feel has "heirloom quality" but it's not perfect. It does show my progression as a woodworker and really it's a testament to how good Marc's videos really are. Quote
Freddie Posted October 8, 2013 Report Posted October 8, 2013 Its beautiful james, the contrasting woods and hardware come together nicely! Quote
..Kev Posted October 8, 2013 Report Posted October 8, 2013 Nicely done! Love the hardware choices! Quote
Byrdie Posted October 9, 2013 Report Posted October 9, 2013 Really nice. Love the traditional look. The darker trim almost gives it the feel of leather banding. Quote
jmaichel Posted October 9, 2013 Author Report Posted October 9, 2013 Thank you for all the nice comments! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.