Recommended Posts

Posted

Despite having been lurking for a while and tied up with some boring and unremarkable shop projects (does anyone really want to see another crosscut sled?) I do have one commission in the works.  A local church has a set of handbells that need new cases.

 

post-211-0-68199500-1375127313_thumb.jpg

 

This is the smallest of the three, with a few of the little bells resting loose inside to provide scale.  Sides are done (white oak) bases are done (white oak with a pine panel) starting to cut pieces for the tops.  Once the boxes are done, it'll be a fun job cutting out and upholstering cradles for the bells themselves.

Posted

Tough to find time and projects always seem to drag towards the middle.  I got the parts cut for the tops.

 

post-211-0-66130300-1375307431_thumb.jpg

 

Yes, the panels are red oak whereas the bodies are white oak.  I had a set of curly white oak boards that I wanted to feature on this project.  Then when time came to mill them, the curls tore out.  Freshly sharpened blades, taking a mere 1/128" at a time, moistening the fibers, sealing with a spit coat of shellac, etc...Nothing worked.  The boards seemed to shred themselves just looking at the planer.  Rather than spending hours trying to salvage them I decided to cut my losses and start with a fresh board.  (The panels are glued up and will some day find a use...like the day I get a helical head planer, or a wide belt sander, or something that can handle such wild grain.)

 

Looking over what the yard had on hand, I settled on a big, broad piece of red oak that yielded all three of the tops plus a nice piece of leftover.  Rests then the question of the obvious color difference.  As an experiment, I put some offcuts in ammonia vapors overnight.  With a quick swipe of linseed oil, the results are promising.

 

post-211-0-24408100-1375307388_thumb.jpg

 

No, it still doesn't match but at least it makes the two harmonize better.  The white oak started dark and went darker, the red oak lost its pinkish cast and mellowed to a honey, amber hue.  Next hurdle will be executing the carvings on the tops.  It's the church's sesquicentennial next year, so the panels will feature incised numbers 1864-2014 and a relief carving of a winged lion.

 

post-211-0-30303700-1375307334_thumb.jpg

 

Any recommendations on whether I glue the tops together first or carve the panels and then glue up the frames?  I suppose it's a question of which operation I'm more likely to bungle.

Posted

Rob, since you have some leftovers, I think I would start by carving the panels. If you mess one up, you can always make another and then frame them all at the same time. Nice looking project btw.

 

On a different note, see if you can blend the colors by using some wood bleach on the red oak first. Try a sample first, and if it works, wait until you have done your carving and then bleach out the panels. If you bleach first and then carve, you will expose unbleached wood in the carving.

Posted

Thanks, Troy.  Good thinking but my impatient side won out in the end.

 

post-211-0-90779300-1375392813_thumb.jpg

 

I did a quick test of the carving design and confirmed my suspicion that some of the artwork needs reworking.  Specifically, the tips of the wings need to be redone to avoid having a thin sliver that runs at 90 degrees to the grain.

 

post-211-0-30791100-1375392827_thumb.jpg

 

Unfortunately, the lines of the wings are a major part of what makes the design.  A few tracings and sketches later, I concluded it wasn't something that would take a quick fix.  So, it turns out that I'm not ready to do the carvings but I am ready to glue the tops right now.  Plenty of other projects waiting in the wings, so this one needs to keep moving towards the end zone.

 

Ultimately, the carvings are a bonus and aren't essential.  (I didn't specify them in the proposal...just thought it would be nice.)  Since these aren't getting varnished, in theory I could deliver them and the carvings could be done years from now.  Or maybe I skip the winged lion and just incise the numbers.  Right now, I need to get them out the door.

Posted

Is the mallet a significant part of the glue up? Some sort of caul, perhaps?

 

An essential part, in fact.  I ran short of 12" clamps and had to use a 24" clamp for the last one.  The mallet serves as ballast to keep it from tipping over.  :)

 

Cleaned house (the shop was starting to look like a demolition zone) and staged a group progress photo for the church's newsletter.

 

post-211-0-50566200-1375476952_thumb.jpg

 

And the baby bell said, "This box is too big...this box is too small...this box is just right."

Posted

re-lief (n.) A sensation experienced during the routing of hinge mortises when, having witnessed a chunk of the workpiece tear out and fly across the bench, one not only locates the lost piece but successfully glues it back on.

  • Like 1
Posted

...and with the hardware done, today I finished sanding.  At last, I can glue the sides onto the bases.

 

post-211-0-75043400-1375833791_thumb.jpg

 

Leaving town for the weekend.  Assuming I can get all these glued tonight, my goal for tomorrow is to build a tent and let these guys breathe ammonia while I'm gone.

Posted

Used to do the same with Japanese Beetles in the garden as a kid.... Rob, knowing you desired that design but did not feel ready to carve it, had you considered burning or does that concept belong to a lower class of craftsmanship?

Posted

I really gotta get glasses.  I read that too quickly and came up with, "With that, I'm off to Vomit."  

 

Cleaned a barn with horses and a chicken coop for a lot of years.  Brings back memories.

 

Sure hope they turn out nice!  The woodworking sure is top notch.

Posted

(Writing from the road.)

 

I ended up opening it up before I left.  This was my first fuming with anhydrous ammonia and it goes a lot faster than the household ammonia I've used in past projects.  I'm more than happy with the color it took even just in 24 hours.  Most of the white oak took on the grayish color of raw walnut.  Some of it stayed fairly light (the smallest box now has a two-toned stripe...good thing the sides are all cut from the same board and kept in order.) and it matches the red oak quite nicely.  It'll be good that the garage can air out before I get back.  Of course, the first thing then will be to stink it up again with linseed oil.

 

post-211-0-98947800-1376052465_thumb.jpgpost-211-0-59780400-1376052453_thumb.jpg

 

A big pile of spacers and blocks custom made just for this fuming.  Looks suspiciously like trash now.

 

post-211-0-90492300-1376052651_thumb.jpg

Posted

A big pile of spacers and blocks custom made just for this fuming.  Looks suspiciously like trash now.

 

 

You know that as soon as you toss that out, you'll need it right?

 

Looks great BTW!

 

Posted

You know that as soon as you toss that out, you'll need it right?

 

Bring it!  Everything in that picture came from the "oversized useless garbage" pile.  It had its fifteen minutes of fame in the "briefly useful" pile and now fits into the regular trash bin.  If I need more, the oversized useless garbage pile is still there.

Posted

Handles and most of the hardware attached.  The lid supports come with screws that are too long, so those are on hold until the next trip into town.

 

post-211-0-89707200-1376708098_thumb.jpg

 

Running out of excuses to make those bell cradles:  The stock is milled, the circle cutter is sitting patiently next to the drill press, the cotton tape to line the cradles is bought, the boxes are all assembled and finished...Sigh.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 39 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined