Shopdog19 Posted August 15, 2013 Report Share Posted August 15, 2013 I am fixing a round table top for a friend that has broken in two, I am using biscuits to connect the two pieces (which used to be hinged) what is the best way to glue this up and clamp as it is round???? Quote Link to comment Share on other sites More sharing options...
TerryMcK Posted August 15, 2013 Report Share Posted August 15, 2013 You could try hot gluing some cauls to the underside of the table top setting them parallel to the straight edges. Then just use regular clamps pulling the cauls together. Marc did this on his angled headboard build http://www.thewoodwhisperer.com/videos/platform-bed-pt-2-the-headboard/?category_name=marcs-projects You can then knock the cauls off after the glue has cured. You could also use a band clamp running around the perimeter to pull the joint together. On both methods use flat cauls spanning the joint either side (maybe 2 x 4s) with clamps to keep the two sides level to each other. Make sure you put something in between the caul and the wood to prevent the caul from becoming part of your project due to glue squeeze out. Quote Link to comment Share on other sites More sharing options...
Grain Guy Posted August 15, 2013 Report Share Posted August 15, 2013 I clamp c clamps to the top and grab them with a parallel clamp. You need to have some 1/4" protection blocks for your c clamps. Also, go ahead and position the spine of the c clamp against the table edge with a block between. I hope this makes sense. It might make more once you start trying it. Try a dry run. 1 Quote Link to comment Share on other sites More sharing options...
rodger. Posted August 15, 2013 Report Share Posted August 15, 2013 You could try hot gluing some cauls to the underside of the table top setting them parallel to the straight edges. Then just use regular clamps pulling the cauls together. Marc did this on his angled headboard build http://www.thewoodwhisperer.com/videos/platform-bed-pt-2-the-headboard/?category_name=marcs-projects You can then knock the cauls off after the glue has cured. +1. Should work well. Quote Link to comment Share on other sites More sharing options...
Popular Post wdwerker Posted August 15, 2013 Popular Post Report Share Posted August 15, 2013 Or you can use some scrap to make a clamping caul. Trace the curve on some scrap and cut it out with a bandsaw or saber saw. Pad the inside with an old leather belt or some thick fabric. You can cut some parrallel flat spots on the outside edges to accomodate your shorter clamps. You might need to add a few blocks above and below to keep the caul from slipping off the curved edge while you apply the pressure. 3 Quote Link to comment Share on other sites More sharing options...
dwacker Posted August 15, 2013 Report Share Posted August 15, 2013 I just shoot a couple finish nails in the edges. use a piece of scrap to support your gun off the edge so the nail sticks out about a 3/8" after you shoot it. Nip off the tip at an angle and push the two pieces together. Just use regular clamps it wont slip. Quote Link to comment Share on other sites More sharing options...
Shopdog19 Posted August 15, 2013 Author Report Share Posted August 15, 2013 Thx for the info, I don't have CA glue is there another alternative to use in its place? Quote Link to comment Share on other sites More sharing options...
TRBaker Posted August 15, 2013 Report Share Posted August 15, 2013 Titebond III Quote Link to comment Share on other sites More sharing options...
Grain Guy Posted August 15, 2013 Report Share Posted August 15, 2013 I just shoot a couple finish nails in the edges. use a piece of scrap to support your gun off the edge so the nail sticks out about a 3/8" after you shoot it. Nip off the tip at an angle and push the two pieces together. Just use regular clamps it wont slip. Nice! Quote Link to comment Share on other sites More sharing options...
Chris H Posted August 15, 2013 Report Share Posted August 15, 2013 Sounds like lots of good options, another inexpensive solution is ratcheting clamps (tie downs). Just protect the work piece with something where the ratchet sits. Quote Link to comment Share on other sites More sharing options...
Shopdog19 Posted September 19, 2013 Author Report Share Posted September 19, 2013 I was to lazy to make cauls, so I tried the ratcheting tie down idea and i got frustrated with that as I only have 2 arms and the wait list to get another 6 arms implanted was to long, so I chose to use 2 48" bar clamps and they worked fantastic. thanks for all the great ideas, keep up the great support Quote Link to comment Share on other sites More sharing options...
Sue Posted August 23, 2019 Report Share Posted August 23, 2019 Hi I have a round table to clamp as well, how did you get the bar clamps to stay in position on a round table? Quote Link to comment Share on other sites More sharing options...
RichardA Posted August 23, 2019 Report Share Posted August 23, 2019 2 hours ago, Sue said: Hi I have a round table to clamp as well, how did you get the bar clamps to stay in position on a round table? Sue... This post is 6 years old, and there's only one or two guys still on the site. As for your clamping problem, take a board and match the curve, leaving the other side flat, and use hot glue to hold that piece in place. Apply your clamps and when done, apply a little heat from a heat gun or hot hair dryer and knock the piece off. You'll need to sand afterwards. Quote Link to comment Share on other sites More sharing options...
treeslayer Posted August 23, 2019 Report Share Posted August 23, 2019 2 hours ago, Sue said: how did you get the bar clamps to stay in position on a round table? yeah, what Rick said, jig saw a curve to match, leave the other side flat, instead of glue maybe screw a couple of short cauls on each end of your scrap piece to hold it in place while you clamp, and do a test run without glue first, oh, and welcome to the forum Sue Quote Link to comment Share on other sites More sharing options...
wtnhighlander Posted August 24, 2019 Report Share Posted August 24, 2019 Another variation, if you have more clamps than wide scrap boards, is to sandwhich each half of the circle between two skinny cauls, like good old 2x4s. Clamp them tightly, them clamp across the joint, catching these clamps on the ledge formed by the cauls. You'll need to clamp above and below, slowly increasing the pressure evenly on each side, or the piece will fold at the joint. Quote Link to comment Share on other sites More sharing options...
Sue Posted September 14, 2019 Report Share Posted September 14, 2019 On 8/23/2019 at 11:41 PM, treeslayer said: yeah, what Rick said, jig saw a curve to match, leave the other side flat, instead of glue maybe screw a couple of short cauls on each end of your scrap piece to hold it in place while you clamp, and do a test run without glue first, oh, and welcome to the forum Sue On 8/23/2019 at 11:41 PM, treeslayer said: yeah, what Rick said, jig saw a curve to match, leave the other side flat, instead of glue maybe screw a couple of short cauls on each end of your scrap piece to hold it in place while you clamp, and do a test run without glue first, oh, and welcome to the forum Sue Thank you very much for ypur help, what a great idea. Thank.ypu Quote Link to comment Share on other sites More sharing options...
Sue Posted September 14, 2019 Report Share Posted September 14, 2019 On 8/24/2019 at 2:04 AM, wtnhighlander said: Another variation, if you have more clamps than wide scrap boards, is to sandwhich each half of the circle between two skinny cauls, like good old 2x4s. Clamp them tightly, them clamp across the joint, catching these clamps on the ledge formed by the cauls. You'll need to clamp above and below, slowly increasing the pressure evenly on each side, or the piece will fold at the joint. Thank you, I didn't know what cauls were but I do now, so I just have to find someone who can to curve in the wood for me, as this is a perfect system to keeping the joins flat and clamped together while drying. Thank you Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.