Tony Wilkins Posted June 10, 2014 Report Posted June 10, 2014 In trying to the the last edge square on my little shaker table top I've found that a panel gauge would come in very handy. Don't have one. I know I could probably make one but I'm looking at the offerings from Lie Nielsen and Hamilton Tools. The Hamilton is substantially more but is longer (which could come in handy when I build a dining table in the future) and seems better built. Thoughts on this decision? TIA, Tony Quote
Trip Posted June 10, 2014 Report Posted June 10, 2014 I've got the LN and used the H. They both work well, the H is slightly nicer design with better fit/finish... The H handles much wider panels, but I rarely mark panels over 18" wide... For really wide panels, I just measure two reference points and use an 8' straight edge or FT track, if I'm using the TS55... I think you'll be happy with either choice. Quote
G S Haydon Posted June 10, 2014 Report Posted June 10, 2014 "I just measure two reference points and use an 8' straight edge" boom! Tony both of those tools will be sweet but this simple solution is perfect. 1 Quote
wdwerker Posted June 10, 2014 Report Posted June 10, 2014 If I was going to spend that kind of money I would get one of Woodpeckers T Squares , the ones with all the tiny holes in the middle. You can put a .07mm mechanical pencil or a sharpened scribe in the holes to mark every 1/32 or 1/64 I think . I have the 4" and 6" wrap squares with this feature and use them in the shop constantly. Then they came out with the tee squares as well. 1 Quote
wdwerker Posted June 10, 2014 Report Posted June 10, 2014 I just looked, the holes on the Tee square are 1/16 apart. But they have an aluminum panel guage for $129 , it's a one-time tool. They usually make a few extra.. It hasn't shipped yet I think. Call Woodpeckers and see if you can still get one. Quote
wtnhighlander Posted June 11, 2014 Report Posted June 11, 2014 For large panels you can always buy an inexpensive drywall T-square and drill a hole or file a notch for your marking device at the desired distance from the T. Quote
Tom King Posted June 12, 2014 Report Posted June 12, 2014 I've been doing this stuff for long enough that some of the things I've made now qualify as being antiques. I never even remember having a thought that I needed one of these. Quote
Tony Wilkins Posted June 12, 2014 Author Report Posted June 12, 2014 Seems as if I might be better served with a good long straight edge at this point (have a folding 2 foot as the longest and a 12" combo square). Quote
Trip Posted June 12, 2014 Report Posted June 12, 2014 ==>a good long straight edge I wouldn't spend $$ on a 'nice to have' until the 'need to haves' are taken care of... A good straight edge is a 'need to have'... A panel gauge is not... Soooooo.... Now you'll receive lots of suggestions for straight edges... I've got four pieces of kit that I use as a straight edge on a regular basis -- one is purpose-made, one is shop-made and two are improvised: Purpose-made: Six foot Starrett Machinist's straight edge -- expensive, not necessary for a wood-shop, but handy for setting-up woodworking machinery. Got mine from a machine shop closing its doors -- even used, they are expensive; Shop-made: For needs up to 36", a piece of straight-grained stable stock carefully jointed is more than adequate... I've got one in QSWO that's been around for years -- and has the battle scars to prove it..... It was used about 90% of the time until I got a track saw... I made two for winding sticks, so they do double-duty. Improvised: 6' Stabila level -- expensive, handy for setting-up stationary machine; great for setting bases for base cabinets, built-ins, bookcases, etc. BTW, I've also got the 10' Stabila for outdoor DIY - used rarely, but very useful when you do. Improvised: 8' section of Festool track for use with a TS55... It's now my impromptu straight edge used about 75% of the time... Quote
Tony Wilkins Posted June 12, 2014 Author Report Posted June 12, 2014 I'm planning on using some of the beech it have to make a 3' straight edge and winding sticks Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.