Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Just out of curiosity

Featured Replies

I remember in the 60s and 70s that home woodworkers would all have radial arm saws.

This was, as best I can tell, their source for that perfect 90 degree cut.

And there were other things that could be done with them, such as mitering and molding cutters.

A couple of years ago I was in the shop of a local self-employed cabinet maker.  He had one on the wall of his shop.

But oddly I rarely read/hear discussions of this tool.

Are they just out of vogue?

Have they been largely replaced by a combination of (a) the sled and (B) the sliding compound miter saw?

Or are they just not any fun to talk about (there's nothing there)?

 

Have they been largely replaced by a combination of (a) the sled and ( B) the sliding compound miter saw?

 

 

This one.

 

The SCMS is safer and more accurate.  The RAS has taken many fingers and is harder to get dialed in dead nuts and keep it that way...from what I hear.  I've never had one in my shop and the one in my high school shop class was unplugged and blade-less...for a reason.  There are a lot of old timers out there who still use them and do great work...but if you're just getting into things and you need a crosscutting machine, there aren't a lot of good arguments going for the RAS over the SCMS.

This one.

 

The SCMS is safer and more accurate.  The RAS has taken many fingers and is harder to get dialed in dead nuts and keep it that way...from what I hear.  I've never had one in my shop and the one in my high school shop class was unplugged and blade-less...for a reason.  There are a lot of old timers out there who still use them and do great work...but if you're just getting into things and you need a crosscutting machine, there aren't a lot of good arguments going for the RAS over the SCMS.

 

+1 to this. Growing up my dad had a radial arm saw, and it was the "king of the mountain" he used it for ever miter and cross cut when doing trim and moulding in the house, as well as building stools and other random things. They can be dangerous however, as well as take a large footprint for what it does. 

  • Author

I wasn't thinking about getting one.  Just noticing the changes.  I do that.  It's a habit.

Frank Howarth has one of them, an old Dewalt, and he uses it all the time in his videos. Sometimes he uses it with a dado stack. Wish one could do that with a SCMS.

It was the first stationary power tool I purchased in the early 80's and used it for all cutting until I bought my first table saw in the mid 90's.  Eric is right, it takes a little work to tune them up and it is easy for them to get out of whack.  My Dad had one for as longs I can remember.  Between the two of us we had one injury, my dad got the corner of his finger once but pretty minor compared to the stories  out there.  I think about getting rid of mine for the space but sentiment kicks in and I end up keeping it... unused.

If I had a bunch of extra room in my shop, I would put one in but, like many here, I just don't have the space.

Frank Howarth has SEVERAL of them, an old Dewalt, and he uses it all the time in his videos. Sometimes he uses it with a dado stack. Wish one could do that with a SCMS.

Fixed it...

Someone gave me one years and years ago. I built a work table around it and I'm sure I used it for something. I got rid of it as soon as I found there were safer ways to cut off a finger!

I still use one, only set up for very accurate 90 degree cuts, as well as a sliding miter saw, and a non sliding miter saw that is not permanently mounted.   Sometimes it's nice to have two miter saws set up for a particular job, so you don't have to switch angles for every cut on small pieces.   Almost all tenon shoulders are cut on the RAS-one cut to perfect finish with a stop block for repetitives.  I rarely, if ever crosscut on the tablesaw.  The only sleds I use are special purpose ones.  It always felt more dangerous to me to crosscut on the tablesaw, than with a RAS.

My dad had one, one of the few major tools he had for woodworking, man if that sucker grabbed a board, something had was going to happen, it's just that you never knew if the board was going to go flying or the saw head was going to coming tearing out at you!

My dad had one, one of the few major tools he had for woodworking, man if that sucker grabbed a board, something had was going to happen, it's just that you never knew if the board was going to go flying or the saw head was going to coming tearing out at you!

 

Good point. RAS are used in a climb cutting motion, hence the greater danger in using them. 

Good point. RAS are used in a climb cutting motion, hence the greater danger in using them.

I'd still like to have one for cross cutting dados on long stock.

I'd still like to have one for cross cutting dados on long stock.

 

It'd be great to have one for doing guitar fretboards, specifically fanned fretboards.

It'd be great to have one for doing guitar fretboards, specifically fanned fretboards.

I had to google that one, are those all dados?

I have one over in the corner not being used because of all of the reasons given but I may integrate it in somehow just for breaking down larger things.  They're pretty easy to make dados and the cross cuts are fairly accurate but in all threads on this site about RAS (and there are many) you'll always see 'fingers' mentioned.  Any tool that's mentioned here and the mere mention causes the people here to immediately begin bringing up body parts is probably good to stay away from. :)

I'd still like to have one for cross cutting dados on long stock.

I have used mine in the past for cutting dados and it wasn't my favorite thing to do.  That climbing motion Tom mentioned gets multiplied for every additional blade you add.  You need your wits about you.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.