Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Help me tune my drill press

Featured Replies

So I have had this ridgid dp1550 in my shop for a few years. I am finally getting around to tuning it up for furniture making use.

I levelled and squared the table to the bit, but I am getting some runout, and I don't know what good tolerances are, or how to cure what ails me.

So I started by cleaning the chuck (spraying up into it with wd40), and cleaning up the area. I then found a drill jobber (to use as a refrence pin) and used my calipers to make sure it was a consistent diameter. Same measurement at multiple points.

post-6372-0-11731700-1437963874_thumb.jp

Then I set up dial indicator, and zeroed it.

post-6372-0-56900500-1437963947_thumb.jp

post-6372-0-45796200-1437963986_thumb.jp

Then, turning the drill by hand I got a max reading of 28 or so on this dial.

post-6372-0-04406100-1437964051_thumb.jp

I thought this seemed excessive, and I tried to remove the chuck, but I can't get it off to clean it.

Am I too far out? How do I fix the issue?

Are you tightening all three key positions? 28 thou is a lot of runout, especially that close to the collet. I would remove, clean and reseat the chuck and taper as a first step. Most drill presses have a tapered wedge key that can be inserted into a slot on the shaft to drive the taper out of the spindle. I've heard of some having a little luck sticking the chuck assembly in the freezer for a while, then tapping out the collet.  I've never tried that myself.

  • Author

No wedge key on this press (Jacobs chuck I think it's called). I redid my test with a 1/2" router bit and my results improved to about 15 on the dial.

Yes, using all 3 tightening locations.

Are you sure it doesn't have a wedge key?  Lower the spindle down as far as it will go and see if there's a slot in the shaft above the chuck. If so, you can drive a wedge key into that slot and it will force the chuck and the taper out.

  • Author

Are you sure it doesn't have a wedge key? Lower the spindle down as far as it will go and see if there's a slot in the shaft above the chuck. If so, you can drive a wedge key into that slot and it will force the chuck and the taper out.

post-6372-0-50017600-1437966353_thumb.jppost-6372-0-59494400-1437966373_thumb.jppost-6372-0-02736600-1437966393_thumb.jp

Seems like I used a pair of hardwood wedges with a "U " cut in the center, coming from opposite directions and a huge clamp to force them inwards. But it was over 20 years ago so I might have forgotten a step.

I saw a mechanic use Freon to chill a part before driving it loose . That might get you in trouble these days.

  • Author

Has anyone looked at the owner's manual?

Yes - not much help. Says to hammer it off. Tried a little force, but don't want to damage it.

  • Author

Look at the top of the drill press. It may have a hollow spindle with a draw rod like a milling machine.

Not sure how to go about this.

  • Author

Chuck up a slide hammer, improvised or otherwise. Threaded rod, double nut, washers, pipe.

If the chuck is closed, will it damage anything? All I have read indicates to open the chuck fully before attempting removal.

If it's not fully opened when installing or removing you will damage the jaws, either with the mallet (when tapping it in) or when it hits the base or the floor (when tapping it out using a ball joint separator, if you don't catch it in time). The jaws must be completely hidden from view.

I like Steve's suggestion of making a horseshoe shaped wedge to work around it.  It would apply equal force to both sides to keep from damaging the taper.

Yeah, he needs something like this:

 

image_16274.jpg

The flat part must be facing the chuck, then you force it in with a mallet, tapping on the handle.

  • Author

I may just replace the whole spindle and chuck. I can't find out the morse taper on it though. I have the manual, but no mention of the taper.

Well, I have serviced several but not this particular model. I have never had the jaws of the chuck fall on the floor while in tension, but how hard is it to catch on a towel? For sure don't hammer hard enough to destroy the chuck, but 90% is getting the force vectored to the precise axis. It should not take monstrous amounts of force.

Yeah, he needs something like this:

 

image_16274.jpg

The flat part must be facing the chuck, then you force it in with a mallet, tapping on the handle.

 

So.. he needs a tuning fork to tune his drill press?

  • Author

Well, I have serviced several but not this particular model. I have never had the jaws of the chuck fall on the floor while in tension, but how hard is it to catch on a towel? For sure don't hammer hard enough to destroy the chuck, but 90% is getting the force vectored to the precise axis. It should not take monstrous amounts of force.

Okay, I get it. Is the only danger in using a slide hammer the risk of the Chuck being damaged from falling on the table or floor?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.