Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

GF salad bowl vs mineral oil

Featured Replies

For the cutting board crowd,  I have always used GF salad bowl finish but recently decided to give straight up mineral oil a go.  3 coats in and I feel like it is still absorbing a lot of oil. Where was the tipping point that you feel it is properly sealed?  After 3 coats of GF, I felt like it was solid and creating a film on top.  

Mineral oil will not form a film.  I put 2-3 coats of mineral oil on, and that is plenty!

Yeah mineral oil will never "seal" anything.  The wood will drink it up until it's saturated and as soon as you wipe off the excess it starts the process of drying out.  After a few months your cutting board will seem dry and you'll need to reapply.  Mineral oil doesn't cure.  Salad bowl finish is varnish, heavily thinned.

  • Author

The reason I'm switching to mineral oil is to get away from the film.  I loved the look of the varnish,  for about a week but the knife marks make it quite noticeable.

Will the mineral oil not protect the wood from food juices seeping in and staining it? 

A mineral oil and beeswax combo seems effective. My gf abuses the heck out of the one i made her. I finally reapplied after a few months but it has held up well.

Its been suggested that the oil wax mixture on an end grain board helps push moisture back out of the wood as it dries. I dont know how true this is, but it seems to be working. The board doesnt smell, and has very minimal stains showing considering the gallons of tri-tip blood that have sat on it.

I do 2 generous coats of straight oil, waiting atleast 24hrs between. Then 1 heavy coat of heated oil/wax, hand-buffing it in thoroughly and letting it sit until the wax starts to cool. Then wipe away and lightly hand-buff again. Next day the cloudiness dissapears and they look nice.

The key is taking care of these boards. Clean em and let dry on edge after each use.

Sent from my SAMSUNG-SM-G890A using Tapatalk

+1 on the mineral oil / beeswax combo. I saturated my boards with straight oil, then applied the oil / wax mix. The wax really slows down the drying out process, and repells water well. My local Lowes now carries an oil / wax butcher block finish, but those are mostly oil. I like blending my own to more of a paste .

I bought it on Amazon. 5 ounces for like $7. Which is enough for maybe 10 cutting boards the way i mix it (about 20% by volume) .

https://www.amazon.com/dp/B00455IWK6/ref=cm_sw_r_other_awd_zFIDwb3VYNRAW

-

Then i get the oil from the butt-problems isle at Walmart for bout $2.50. Which will do 2 large cutting boards.

Sent from my SAMSUNG-SM-G890A using Tapatalk

12 hours ago, Brendon_t said:

Where do you guys get the wax? 

Whole Foods (or something like that) will have small chunks of beeswax in the pharmacy section.

There's most likely a beekeeper group near you, you can probably get some local stuff for pretty cheap if you make a connection.

There's most likely a beekeeper group near you, you can probably get some local stuff for pretty cheap if you make a connection.

Pretty sure I'd rather overpay than reach out to the local beekeeping community for cheap wax

Sent from my iPhone using Tapatalk

  • Author

I personally won't shop at Walmart but we have a few of the hipster markets around. I'll call them today and see.

50 minutes ago, vinnyjojo said:

Pretty sure I'd rather overpay than reach out to the local beekeeping community for cheap wax

Sent from my iPhone using Tapatalk

Okay.

Mineral oil is nasty stuff. Oils, fats, blood, chicken juices, etc. mix with it in the wood and form a black grunge.

Boards oiled over a period of time can be scraped and produce a black nasty paste that has been growing bacteria out of the oil and garbage. Not a good situation.

 

I just finished a cutting board (first one) and used thinned varnish. It probably will look bad shortly, but that will be better than it becoming a Petr dish.

 

  • Author

I talked to a friend who is a sou chef at a sushi restraint and he said they will wipe their cutting boards (whole counter top) with a mile soap and water blend nightly then they treat them with mineral oil about every few weeks as they look like they need it.

i get not wanting to ingest varnish, although I think most of the nasty stuff is in the drier additives that gas off when curing.  

That's why someone invented glass, so you don't have to worry about eating rotten chemicals and ancient bacteria with your salad.

5 minutes ago, Brendon_t said:

I talked to a friend who is a sou chef at a sushi restraint and he said they will wipe their cutting boards (whole counter top) with a mile soap and water blend nightly then they treat them with mineral oil about every few weeks as they look like they need it.

i get not wanting to ingest varnish, although I think most of the nasty stuff is in the drier additives that gas off when curing.  

I figure if I have the option I'd rather not have the finish chipping off as I cut on it.  (I'm really not afraid of some varnish chips, I'm sure spraying/ wiping the stuff without a mask is worse for you.  And I do that from time to time.)  I've also never had my cutting board turn black. 

1 minute ago, Daniel. said:

That's why someone invented glass, so you don't have to worry about eating rotten chemicals and ancient bacteria with your salad.

Someone obviously doesn't care about their knives.  Would you use your favorite chisel on a glass surface? 

2 minutes ago, xxdabroxx said:

 

Someone obviously doesn't care about their knives.  Would you use your favorite chisel on a glass surface? 

I confused things. Thought you were talking about salad bowls (?)

As for cutting boards, olive oil from time to time... you have to clean them really hard using salt, lemon, bleach, whatever keeps them free of bacteria, so the finish won't last anyways...

  • Author

I've actually never had any varnish chip off in the last year of using my board hard.  I've gotten some knife marks but even normal chopping doesn't Mar it.

I've never tried buy would not want to use olive oil or any other oil that may spoil.

11 minutes ago, Brendon_t said:

I've actually never had any varnish chip off in the last year of using my board hard.  I've gotten some knife marks but even normal chopping doesn't Mar it.

 

That's because you're being so delicate at washing such table... Keep a good stack of woodworking magazines near your throne, you may have to spend a lot of time there anytime soon :D

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.