Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Workbench Height Question

Featured Replies

While working on some shop cabinets this weekend, I decided to break out my #4 smoother with the newly sharpened blade and use it to smooth all of the trim instead of sanding. The smoother did the job very nicely, but as the work went on, my back started to get sore from bending over. When I built the bench umpteen years ago, I read up on all the different ways of determining bench height and came up with 36 inches, which has worked well over the years. As I get older, I seem to be hunching over more to see what I am working on.

I am short (was 5' 8", but now 5' 7") and have short arms to boot, (I don't recommend this combination if you have a choice), but I am seriously thinking about raising my bench a couple of inches. I put my hands out as if to work on something and seem to naturally place them 2-3" above my bench top.

Has anyone else tried this? If so, what were your results? I'd appreciate your thoughts.

I am not tall either and like my benches to be higher than 900mm. (standard bench height in Australia but 912mm is 36 inches) You could put a piece of timber underneath the legs to try it and see. Maybe 2 inches?

I raised mine from 34 1/2" to 37 1/2 inches do to the fact that I'm still 6'2" at 73 years... In fact, I've set all my machinery ,countertops and benches at 37 1/2"  Blocking a tad larger than the original feet raised the bench, perfectly!

As already said, test out a new height by adding temporary spacers (make sure they are firmly attached and stable) to lift the bench.  I suggest trying out the new height for a few weeks or through a project, etc.  Feel free to adjust the spacers until you get what works best for you.  Once you've dialed it in, make the change permanent.

At the end of the day, the perfect height is the one that is best for you.

One other thing to consider is your body position while working.  I'm sure others have some good feedback, example links, etc. but sometimes adjusting how/where you stand can make a big difference and be a lot less stressful on your body.

I'm with most of the previous posts. 'Standard' methods for determining workbench height always seem too low for comfort to me. My bench is 36" ( and I'm 6' ), but that is so I can use it for TS outfeed. Otherwise, I think I would come up another inch, or even 2. I suppose full-on hand tool guys benefit from mechanical advantage when planing on a lower bench, but I don't mill stock by hand.

You have to know your project load. Low benches make more sense for slab work or deep case work. If you aren't building slab tables or wardrobes where you need to plane clear to the middle of the bench, a higher bench may make a lot of sense. Benchtop Moxon vises and joinery benches exist because all of us find some tasks to be too low on a standard bench. Part of my bench build lag is the desire to not engage a once in a lifetime build in an unsatisfactory way. 

For the types of work I generally do, a higher bench is more comfortable. I'm 5'10" and built my bench at 36". I built my MFT to 37 1/2" so I'd have a little flexibility depending on the work. My assembly table is at 30" but I'm thinking I may lower that an inch at a time until it gets comfortable.

A good question to ask - I am currently reading Chris Schwarz' The Workbench Design Book and he covers that a bit. The problem you describe is that a height that is suitable for planing, isn't exactly suitable for sawing or other operations. You can certainly raise your workbench up, but then you make more work for yourself when you go back into planing mode.

Like @C Shaffer said, an alternative suggestion would be to make a raiser block double-screw/moxon vice for the top of your workbench. That way when you are not planing but need workholding at a different height, you can can adjust. Alternatively, you could fashion some riser blocks attached to some stout hinges to raise your workbench that way.

I'm reading Jim Tolpin's book "The New Traditional Woodworker" and he gives these heights: for joinery elbow height, for planing wrist height, assembly tip of fingers. I'm planning to build my new bench to wrist height, then use a moron vise for joinery operations. Tolpin's gives good solid physiology and practical reasons for these bench heights. 

  • Author

Thanks, all, for your input. I had planned on some temporary riser blocks, but wanted to see what others have used before jacking my bench up to put the risers in. That sucker is heavy!

The ideas in the jack bench are intriguing. I wonder how hard it would be to use an air cylinder? The way he clamps the top and bottom is smart. Looks like it would be sturdy.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.