ChrisG-Canada Posted March 14, 2016 Report Posted March 14, 2016 On Saturday I 'attempted' to tilt my table saw blade to 45 degrees so I make a tea box for my wife. Within the 1st degree of tilt I noticed a LOT of resistance at the hand wheel (which I had unlocked). I thought that maybe the gears were dirty/packed with sawdust so I unplugged the saw, opened up the side panels on the cabinet and give everything a good vacuum. The gears looked ok but when I tried again the resistance was worse - for either direction of tilt travel. I tried turning the tilt hand wheel fairly hard and the noticed the saw blade wasn't tilting evenly from front to back - the back of the blade was getting a LOT closer to the edge of the clearance insert and then the blade seemed to suddenly drop about 2 inches or so. I, of course, stopped everything to grab a flashlight and started looking at everything very closely. I then carefully removed the blade which was now wedged tightly against the cast itron tabletop - how do I tell if the blade is damaged? I then performed a much closer inspection of the mechanism inside the saw cabinet and found a large crack in the rear Trunnion bracket and that the rear Trunnion itself had dropped approx 2" from where it was supposed to be supported by the bracket. At this point I was pretty frustrated because I HATE working on machines. I called the manufacturer warranty support and they weren't available on Saturday but the person at their call centre was good about getting my information and starting a warranty claim. I e-mailed them some pictures and was promised they would get back to me early in the week. They actually called me this morning before noon ( ? ) and I talked with them. This afternoon I took off the saw table top- cast iron is heavy ? . I also dis-mounted the motor then un-bolted the rear Trunnion bracket - it came out in 2 pieces. Good news is that I'm just a couple days short of the 1 year warranty date so they are sending me a new rear Trunnion bracket and also the rear Trunnion itself (in case it's damaged). Should be sent tomorrow and I hope to have by the end of the week. Here in Canada sometimes shipments from the US take longer than seems reasonable. I suspect the part could have been damaged during shipping - maybe dropped? Thinking back, this was actually the first time I tried tilting the blade. I did adjust it slightly when I got it but only to true it up to 90 degrees and since then hasn't been touched. Lesson learned for me - try EVERYTHING out on a new tool and check it over very carefully. So far I haven't mentioned that my saw is a Grizzly G1023RLW because I don't want to start a brand bashing thread. The truth is that I think this could have happened with any brand and so far Grizzly has been very friendly and quick to respond. They actually apologized to me for any trouble I've had. I'll post again when the parts arrive and I struggle/figure out how to install them and re-mounts he motor. In the meantime, here's a few pics... Quote
knotscott Posted March 14, 2016 Report Posted March 14, 2016 Wow....that sucks! Pretty strange. If nothing catastrophic happened to cause it, I can't help but wonder if there was an issue at the factory that just finally showed itself. Quote
Brendon_t Posted March 14, 2016 Report Posted March 14, 2016 Seems like 11 months is about the going rate. My band saw gave up with 14 days left in warranty Quote
Kentuk55 Posted March 14, 2016 Report Posted March 14, 2016 Holy Moly!! How old is your saw? I just ordered a G01023RL earlier this afternoon. That freeks me out! Quote
Chestnut Posted March 14, 2016 Report Posted March 14, 2016 Holy that's unfortunate. I think the thing that would bother me the most about that is having to take all that heavy stuff off the saw. Good thing they worked with you and sent you more than you needed just in case. Good luck getting it set back up hope it all goes smoothly. Quote
Chet Posted March 14, 2016 Report Posted March 14, 2016 Yea who knows you could of had some hairline damage from shipping or some other jolt to it and the stress of you tilting it finally did it in. At least it is getting taken care of. I offset you and Brendon... I have a 20 year old Griz Jointer that is still humming a long, although I did have to work on the switch a couple of years ago. Quote
mat60 Posted March 14, 2016 Report Posted March 14, 2016 This reminds me to service my saw ..Stinks about your trouble. Quote
PeteJr Posted March 15, 2016 Report Posted March 15, 2016 Inspect the casting and the fracture area closely. If you see what look like many small holes that's porosity which will lead to this type of failure. When the new parts arrive compare them visually for a similar condition before you install them. Quote
N00b-in-training Posted March 15, 2016 Report Posted March 15, 2016 Great to hear more great things about Grizzly's Customer Service. Also reminds me that I need to give my cabinet/trunnions a good cleaning and greasing. I don't want to take the several hours to do it, but sure beats days of downtime! Quote
Marcel.F Posted March 15, 2016 Report Posted March 15, 2016 If you're worried about the blade being damaged, tell them you're concerns and see if they'll send you a replacement one. Can't hurt to ask. Marcel--- Sent from my iPhone using Tapatalk Quote
Brendon_t Posted March 17, 2016 Report Posted March 17, 2016 On 3/14/2016 at 1:54 PM, ChrisG-Canada said: So far I haven't mentioned that my saw is a Grizzly G1023RLW because I don't want to start a brand bashing thread. Haha Chris, I just noticed the edit after you first posted it. You didn't need to tell us what saw it was homie, you posted it in this picture. * ) 1 Quote
ChrisG-Canada Posted March 23, 2016 Author Report Posted March 23, 2016 Just to follow up... Yesterday I received the replacement trunnion bracket, installed it, installed the motor, installed the table and calibrated everything. Have I mentioned that I hate working on machines ?. That was enough for me so I called it a day. Today, I double-checked all the alignment calibrations (blade to miter slot and miter slot to fence) and did some test cuts. All seems to be good and now there are no excuses for not getting some projects done ?. 2 Quote
gee-dub Posted March 29, 2016 Report Posted March 29, 2016 Look for the silver lining. You probably did a better alignment than many folks do since you were in it up to your elbows anyway ;-) Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.