collinb Posted February 25, 2017 Report Posted February 25, 2017 ... I find it easier to control the medium even when using a traditional tool. I only had to take a couple small slivers off and this worked out because I could check /verify width on each pass. That's a little more difficult to do if I clamped the wood. Sent from my MotoE2(4G-LTE) using Tapatalk 2 Quote
derekcohen Posted February 26, 2017 Report Posted February 26, 2017 Use a block plane or a spoke shave instead. Regards from Perth Derek 2 Quote
Coop Posted February 26, 2017 Report Posted February 26, 2017 Collin, not a bad idea, especially if the grain is running with you. But I still like the feel of the steel in my hand. Quote
collinb Posted February 26, 2017 Author Report Posted February 26, 2017 Use a block plane or a spoke shave instead. Regards from Perth Derek Probably. As my skills improve. Sent from my MotoE2(4G-LTE) using Tapatalk Collin, not a bad idea, especially if the grain is running with you. But I still like the feel of the steel in my hand. Tx. Gotcha. Sent from my MotoE2(4G-LTE) using Tapatalk Quote
TerryMcK Posted February 26, 2017 Report Posted February 26, 2017 You can also break the sides off a cast iron plane body putting it in the vise like that. 1 Quote
wtnhighlander Posted February 26, 2017 Report Posted February 26, 2017 Old-time coopers used a plane in a similar fashion, but those were long jointer planes, and usually (always?) had wooden bodies. The only time I saw one in action, it was propped against the cooper's torso, with the heel on the ground. The work was pushed down across the blade. Quote
Popular Post derekcohen Posted February 26, 2017 Popular Post Report Posted February 26, 2017 Yes, I built a 36" long cooper's jointer some years ago. They are a tad larger than you realise (3" wide blade) ... For comparison, here it is alongside a Stanley #7 (which is 22” long). It had a fence for jointing on top of a edge .. Or, you could turn it over and use it like this ... Link to article on my website: http://www.inthewoodshop.com/ShopMadeTools/CoopersJointer.html Regards from Perth Derek 5 Quote
Tpt life Posted February 26, 2017 Report Posted February 26, 2017 The reason that both table saw and circular saw exist is because sometimes you take work to the tool and sometimes you take the tool to the work. I think the only critique has been mentioned. Be careful how you load it in the vise. 1 Quote
collinb Posted February 26, 2017 Author Report Posted February 26, 2017 The reason that both table saw and circular saw exist is because sometimes you take work to the tool and sometimes you take the tool to the work. I think the only critique has been mentioned. Be careful how you load it in the vise. Tx. I thought of it like a jointer machine in reverse. And not spinning. Sent from my MotoE2(4G-LTE) using Tapatalk Quote
collinb Posted February 26, 2017 Author Report Posted February 26, 2017 Had to do something similar this afternoon but over a larger area, rather than just to an edge. The Record 060 1/2 did the job nicely. Sent from my MotoE2(4G-LTE) using Tapatalk Quote
Unknown craftsman Posted February 27, 2017 Report Posted February 27, 2017 Sometimes I use my foreplane the same way.The last time was to straighten out some pieces for a cooperd lid.It really works great very easy to control the cut on a odd shaped piece. Aj Quote
BonPacific Posted February 27, 2017 Report Posted February 27, 2017 I use my LV LAJ like this fairly frequently. It's great when working with smaller pieces of stock. As others have said, be careful how much pressure you apply. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.