Recommended Posts

Posted

anyone had this done? if so, anyone had it done with "PLEX pipe"? good? bad?

i am going to re-pipe the house after "5" slab leaks (over the years) - my options are PVC or PLEX. copper is not in the plan.

i live in Florida.

 

Posted

PEX is awesome but not in code everywhere. PEX allows for all fittings to be close to access locations and allows home runs to a plenum (meant manifold) with ease. Fittings now are often tool free, but cost more for that option. I don't see PVC on the job site anymore except for drains and irrigation. 

Posted

ya, i hear you.

but Fl. is living in the past. PVC is the "way".

"that's the way we do it", sorta thing.

don't know about code here. just starting to put feelers out to get estimates.

trying to learn as much as possible. the "web" is all over the place on this subject.

Posted

I'm certainly not a plumber but where I am (in Canada) I don't know even 1 new house that doesn't exclusively use PEX - at least for all the 'runs' through the house.  I know several plumbing contractors and they most often use PEX even when repairing or renovating an older house - the transition from traditional copper to/from PEX is pretty easy.

Posted

here is my last issue - had to tunnel into the leak. it was under the cabinets in the kitchen. :angry:

yes that is a fat guy in the hole!IMG_0945.thumb.JPG.cab6c7989e6b903deea0d8d7b49486e4.JPG

1 minute ago, ChrisG-Canada said:

I'm certainly not a plumber but where I am (in Canada) I don't know even 1 new house that doesn't exclusively use PEX - at least for all the 'runs' through the house.  I know several plumbing contractors and they most often use PEX even when repairing or renovating an older house - the transition from traditional copper to/from PEX is pretty easy.

thank you, - kinda what i  am hearing on the web

and yes, that took a jack-hammer to make that hole!

Posted
4 minutes ago, ghost said:

here is my last issue - had to tunnel into the leak. it was under the cabinets in the kitchen. :angry:

yes that is a fat guy in the hole!IMG_0945.thumb.JPG.cab6c7989e6b903deea0d8d7b49486e4.JPG

Looking a that picture makes... looking at that picture, well all I can say... looking at that picture, nope I got nothing!!!

Do they put PVC in the slab? 

  • Like 1
Posted

That's PEX or CPVC.  I am a plumber, as well as other things.   I like PEX when you can use home runs from a manifold, but I've never felt comfortable with fittings somewhere that's not accessible.

 In old houses, often that have never had plumbing pipes in them before, I run plastic conduit glued together, and pull home runs of PEX through it.  That way, a leak any time in the future won't damage anything.

I've used CPVC more than I've used Pex, and there are times when I prefer it, like if there are problems with old copper pipe.   Copper is not a long term piping if the water is the least bit acidic.

  • Like 1
Posted
17 minutes ago, Chet K said:

Looking a that picture makes... looking at that picture, well all I can say... looking at that picture, nope I got nothing!!!

Do they put PVC in the slab? 

in the slab is copper. repair was copper. my house was built in the early '80's which according to the plumbers i have had at the house, were built with imported copper pipe from china. i know 1 plumber that has re-plumbed 29 homes in my neighborhood due to inferior pipe. we are on city water. everyone i know in this neighborhood has had a slab leak. excellent!:angry:

 

Posted

I built my house in 1980, and used copper pipe.  I don't think it was Chinese, but we have well water that is slightly acidic.  I replaced it all with CPVC sometime in the '90s since it would get tiny pinholes in the copper.   Any time I run a waterline under a slab, it's in something so that it can be pulled out without having to tear up the slab.  Wide turn plastic 1-1/4" conduit elbows will allow 1/2" PEX to be pulled through it.

If it comes up under a cabinet, the cabinet will have a removable floor, and access to a turn in the pipes.  I built the whole house though, including the cabinets, but never had the first callback for anything.

  • Like 1
Posted
3 hours ago, Tom King said:

 In old houses, often that have never had plumbing pipes in them before, I run plastic conduit glued together, and pull home runs of PEX through it.  That way, a leak any time in the future won't damage anything.

Very smart. 

Posted
3 hours ago, Tom King said:

That's PEX or CPVC.  I am a plumber, as well as other things.   I like PEX when you can use home runs from a manifold, but I've never felt comfortable with fittings somewhere that's not accessible.

 In old houses, often that have never had plumbing pipes in them before, I run plastic conduit glued together, and pull home runs of PEX through it.  That way, a leak any time in the future won't damage anything.

I've used CPVC more than I've used Pex, and there are times when I prefer it, like if there are problems with old copper pipe.   Copper is not a long term piping if the water is the least bit acidic.

We have galvanized down here and thought copper was God given. Maybe not? But I still have problems in my future. At least it's not asbestos  :wacko:

Posted

I finished my basement last year and added a bathroom. I've always used copper in the past (father was a pipefitter, it's all I knew) but I used PEX for this and it was awesome. Now I'm kicking myself for not using PEX in a few past remodels. It takes a bit to get your brain to accept that the crimp fittings will hold. The first month I was checking all of the fittings for leaks every day.

Posted

I have access to all of my copper pipe now, home was built in '79 but am slowly finishing my basement and am now wondering if I should replace before it gets closed in, even with no issues(yet)

Posted
2 minutes ago, wdwerker said:

Why replace copper pipe ? If you are hanging a hard ceiling just address any corroding joints and insulate any pipes at the perimeter of the house. 

Because I get hyper paranoid about leaks whenever I do drywall. I am adding a 3/4bath in the basement and that will probably be PEX, just so I have experience with it but the copper all seems in good shape so why mess with it, right?

Posted

For access into basement ceilings, I have used 4' squares of MDO with screws around the edges, and all the joints covered with 1/2 x 1-1/2 Poplar strips. Use the small headed, stainless, self-drilling trim screws, and you don't even have to predrill the screw holes.  They take a T17 bit, which makes it really easy to run them in.

 The strips are held up with 23 ga. headless pins.  That way, the strips can be pulled off and replaced fairly easily if you need to take a panel down.  I spray the MDO before putting up the strips, and prepaint the strips.  One coat of paint with a little roller on the face of the strips covers up the little pin holes, and makes touchup after a repair simple.  MDO is a great base for a perfect coat of spray paint with Pro Classic with little to no prep.

I do almost anything to avoid sheetrock.

If you have had no problems with pinholes in copper since '79, it's probably good to go for a good while yet.  I have worked on houses built in 1934 that still have good copper plumbing in them, including the drain lines.

  • Like 1
Posted

Cast iron is quieter but I have seen long runs rust out along the bottom. I still wonder how many years will it be until they find out PEX has problems or taints the water with something they didn't know was an issue ?

Posted
11 minutes ago, wdwerker said:

Cast iron is quieter but I have seen long runs rust out along the bottom. I still wonder how many years will it be until they find out PEX has problems or taints the water with something they didn't know was an issue ?

Fairly sure it cannot be worse than lead in the solder. 

Posted

I've worked on a fair number of 200 year old houses.  I've never seen two hundred year old plumbing in our houses, and don"t expect anyone will. The real question that matters is how easy it is to fix without messing anything else up.

  • Like 2
Posted
2 minutes ago, drzaius said:

I saw some 2000 year old plumbing in Pompeii that still looks pretty good. Made out of lead though...

Lead is almost perfect for plumbing. It remains flexible, its easy to work with, and is quite resistant to corrosion. Just that one little problem.

Posted

As long as the lead in the solder is exposed to alkaline water the oxidation is supposed to keep the lead from leaching out . Now acidic water like they got in Flint is big trouble .

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   0 Members, 0 Anonymous, 41 Guests (See full list)

    • There are no registered users currently online
  • Forum Statistics

    32k
    Total Topics
    437.5k
    Total Posts
  • Member Statistics

    26,007
    Total Members
    3,644
    Most Online
    FurniCore
    Newest Member
    FurniCore
    Joined