RichardA Posted August 16, 2017 Report Posted August 16, 2017 Only 137? Not so many considering! The bench could have been longer and wider. Just think, you'll be done by the second Thursday of this week. 1 Quote
Cliff Posted August 16, 2017 Author Report Posted August 16, 2017 2 hours ago, Chet said: Nothing quit like some nice monotonous work. Luckily perfect to do in 30-60 minute increments after work, which is really all the time I got anyway. I just gotta make sure I'm done by the weekend so I don't waste my only real free time doing this. Quote
estesbubba Posted August 16, 2017 Report Posted August 16, 2017 Cliff why are you sanding the dog holes? I know for holdfasts that rough is better, so unless you have a reason to sand them, I wouldn't! Quote
Cliff Posted August 17, 2017 Author Report Posted August 17, 2017 12 hours ago, estesbubba said: Cliff why are you sanding the dog holes? I know for holdfasts that rough is better, so unless you have a reason to sand them, I wouldn't! I took one of the dogs from here: https://precisiondogs.us/ and put it in the hole. I have to use a mallet to get them all the way in. Then to get them out, I have to put something in the center hole and try to pry it up enough to wiggle a screwdriver under the head and turn it so it lifts up. Then I have to pull as hard as I can. The only other way I can get them out is to grab with a pair of pliers and pull, which is scraping the metal. I think the place I got it cnc'd at didn't use an exact 20 mm bit or something. But I'm glad it's on the tight side rather than loose. Quote
wdwerker Posted August 17, 2017 Report Posted August 17, 2017 Why not sand the shank of the dogs ? Quote
Coop Posted August 17, 2017 Report Posted August 17, 2017 7 minutes ago, wdwerker said: Why not sand the " shank of the dogs " ? Sounds like a new breakfast drink. 1 Quote
wdwerker Posted August 17, 2017 Report Posted August 17, 2017 Or he could turn around and bite you ! Quote
Cliff Posted August 18, 2017 Author Report Posted August 18, 2017 Well I'm 50 holes deep now, so sanding the shanks would make them super loose in the already sanded holes. Ahh well. Quote
Eric. Posted August 18, 2017 Report Posted August 18, 2017 I think I would have chucked a flap sander up in a drill and hit each one for a few seconds... Although I would be a little concerned about sanding those holes at all, considering they will determine the squareness of anything you do on the table. I do think that sanding down the dogs just a hair would probably have been the better remedy...and much less time consuming. 1 Quote
Cliff Posted August 19, 2017 Author Report Posted August 19, 2017 6 hours ago, Eric. said: I think I would have chucked a flap sander up in a drill and hit each one for a few seconds... Although I would be a little concerned about sanding those holes at all, considering they will determine the squareness of anything you do on the table. I do think that sanding down the dogs just a hair would probably have been the better remedy...and much less time consuming. I wish I had that. It's on my list of things to get. I was pretty careful. I think only one dog hole did I sand too much and there is wiggle room. And that is because I spaced and didn't realize I'd already done it. But really, whether I sand the dog or holes, either has the potential to slightly offset. I think it will be ok. I'll probably check stuff out and see if it's off. Quote
Mick S Posted August 19, 2017 Report Posted August 19, 2017 Not looking to open a can of worms, but did you have the dogs prior to having the top CNC'd? I found that different brands of dogs fit differently. The Parf dogs I use are perfect. The Seneca dogs, not so much. Quote
Cliff Posted August 19, 2017 Author Report Posted August 19, 2017 10 hours ago, Mick S said: Not looking to open a can of worms, but did you have the dogs prior to having the top CNC'd? I found that different brands of dogs fit differently. The Parf dogs I use are perfect. The Seneca dogs, not so much. No. First I identified the dogs I wanted, which were made for the mft/3. Then I found an existing cnc file online for a Festool MFT 3' x 6' table top and took the file to the cnc shop. From looking at the file, it seems good. It says 20 mm. I just wonder if they didn't use the imperial equivalent which might be slightly smaller. If I do this again, I'll probably do the holes myself. Quote
Mick S Posted August 19, 2017 Report Posted August 19, 2017 10 minutes ago, Cliff said: No. First I identified the dogs I wanted, which were made for the mft/3. Then I found an existing cnc file online for a Festool MFT 3' x 6' table top and took the file to the cnc shop. From looking at the file, it seems good. It says 20 mm. I just wonder if they didn't use the imperial equivalent which might be slightly smaller. If I do this again, I'll probably do the holes myself. I did the same thing. I cut (CNC) the first one I made to an online file. When I got the dogs they were too big to fit the holes. I measured them and adjusted my file until they fit just right. Then I ordered some from Seneca and the fit is sloppy. Quote
Cliff Posted August 26, 2017 Author Report Posted August 26, 2017 Liking using this so far. As it's now got everything piled on it, I consider it done! I'm going to have to find a way to store all the MFT related accessories in a convenient fashion. Also added in some protection. Quote
Popular Post wdwerker Posted August 26, 2017 Popular Post Report Posted August 26, 2017 Protection ? Workbench condom ? 7 Quote
Cliff Posted August 26, 2017 Author Report Posted August 26, 2017 1 hour ago, wdwerker said: Protection ? Workbench condom ? That's what I was thinking as I typed it But yeah biggest prob with my last assembly table was all the glue that got stuck to it. Well, that and I made it from particle board and mdf top. Eww. Quote
Dknapp34 Posted August 26, 2017 Report Posted August 26, 2017 Just catching up on this one. Looks awesome, Cliff! I slapped together a quick and dirty outfeed table when I got a new table saw a while back and I am really feeling the limitations now. This would be perfect. Quote
Eric. Posted August 26, 2017 Report Posted August 26, 2017 Looks good, Cliff. I'm pretty jelly of such a large MFT surface. I might throw some kind of finish on there just in case you get glue drips outside the paper condom. Any kind of moisture is murder on MDF. And glue jisom is moist baby. Quote
Just Bob Posted August 26, 2017 Report Posted August 26, 2017 12 hours ago, Cliff said: Also added in some protection. Good looking bench, Cliff. I added a paper roll to my bench and it's great for glue ups and finishes. I use white butcher paper to add some contrast for aging eyes. Quote
shaneymack Posted August 26, 2017 Report Posted August 26, 2017 It's looking awesome Cliff! You'll be building a guitar on that thing before long ! Sent from my SM-G950W using Tapatalk 1 Quote
Eric. Posted August 26, 2017 Report Posted August 26, 2017 4 minutes ago, shaneymack said: It's looking awesome Cliff! You'll be building a guitar on that thing before long ! Did you put any finish on your MDF Shane? Quote
shaneymack Posted August 26, 2017 Report Posted August 26, 2017 Did you put any finish on your MDF Shane? Of course. And I don't even do glueups on it. Danish oil baby !! Sent from my SM-G950W using Tapatalk 1 Quote
Cliff Posted August 26, 2017 Author Report Posted August 26, 2017 2 hours ago, Eric. said: Looks good, Cliff. I'm pretty jelly of such a large MFT surface. I might throw some kind of finish on there just in case you get glue drips outside the paper condom. Any kind of moisture is murder on MDF. And glue jisom is moist baby. I did three coats of minwax wiping varnish cause it's cheap and available. Was going to use Danish Oil but it was out of stock in town. Then I rubbed wax on top of that. I can't tell I put any finish on the mdf at all though. So I wonder if I did enough coats. Quote
Chet Posted August 26, 2017 Report Posted August 26, 2017 11 minutes ago, Cliff said: I did three coats of minwax wiping varnish cause it's cheap and available. Was going to use Danish Oil but it was out of stock in town. Then I rubbed wax on top of that. I can't tell I put any finish on the mdf at all though. So I wonder if I did enough coats. This is what I did with mine. I re-wax every once in a while and any glue that ends up on it just pops of with a putty knife. Although mine is a birch plywood top, not MDF so you might have a different result. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.