Popular Post Ryan. Posted June 28, 2017 Popular Post Report Posted June 28, 2017 Wife wants a blanket chest for the end of the bed in the master bedroom. The rest of the set is alder, so this will as well. This will be my first time working with alder, so should be a learning experience. Here is the working design so far, based on several designs found online. . Not sure on the top right now. I currently have it as a single panel, not sure if I need breadboard ends or if cleats under the panel would be enough to keep it flat. Got the lumber last week, should be ready to work starting this weekend. Till next time. 7 Quote
Unknown craftsman Posted June 28, 2017 Report Posted June 28, 2017 Wow nice looking Alder or ( poor mans cherry) Kinda boring without any knots but very clean . Good luck with your build. Aj Quote
BonPacific Posted June 28, 2017 Report Posted June 28, 2017 Looking forward to seeing how this goes. I'm a fan of Alder (even clear) for it's looks. I assume you're going natural? Quote
pkinneb Posted June 28, 2017 Report Posted June 28, 2017 Nice! I look forward to following along. Quote
Ryan. Posted June 28, 2017 Author Report Posted June 28, 2017 52 minutes ago, Aj3 said: Wow nice looking Alder or ( poor mans cherry) Kinda boring without any knots but very clean . Good luck with your build. Aj 47 minutes ago, BonPacific said: Looking forward to seeing how this goes. I'm a fan of Alder (even clear) for it's looks. I assume you're going natural? Yep going with a natural finish. The bedroom set is mainly clean straight grain alder so trying my best to match that. 1 Quote
Popular Post Ryan. Posted July 7, 2017 Author Popular Post Report Posted July 7, 2017 Manged to get some shop time today. Started work getting the front and back assemblies. Parts rough cut: Got the legs glued up and in clamps as well. Planned a few of the parts thick, hopefully going to get around to starting the joinery on these tomorrow. Legs out of the clamps, will get jointed and planed tomorrow 4 Quote
Ryan. Posted July 9, 2017 Author Report Posted July 9, 2017 (edited) Kept forgetting to take photos, but got a few. Got the tenons cut for the rails. Photo of the rails partially cut. Used the table saw with the rip cut blade in. I was to lazy to set up the dado stack. Mortises got cut with my 1/4 spiral bit in the router then squared up with chisels. Rails dry fitted for the front and back. Grooves cut to house the panels. And finally a test fit of everything so far. The veriticals at a bit looser than I would like, I may end up needing to place a few 1/16 shims to tighten then up. Sent from my Pixel using Tapatalk Edited July 11, 2017 by Ryan. Removing Tapatalk whitespace Quote
Wood Basher Posted July 9, 2017 Report Posted July 9, 2017 This is an interesting project for me because the construction techniques are similar to a project I have at the planning stage, so I have a few questions. How did you cut the grooves to house the panels? Do the vertical dividers fit in the same groove that will house the panels? If so, why is that? (Why not M&T?) My guess is that the extra work for M&T is not needed as the dividers are not under any real load, but then why does it matter that you have them a bit loose? Sorry if these are silly questions. Quote
Ryan. Posted July 11, 2017 Author Report Posted July 11, 2017 On 7/9/2017 at 1:30 AM, Wood Basher said: This is an interesting project for me because the construction techniques are similar to a project I have at the planning stage, so I have a few questions. How did you cut the grooves to house the panels? Do the vertical dividers fit in the same groove that will house the panels? If so, why is that? (Why not M&T?) My guess is that the extra work for M&T is not needed as the dividers are not under any real load, but then why does it matter that you have them a bit loose? Sorry if these are silly questions. Grooved in the rails where cut using a rip blade at the table saw, the ones in the legs were done with a router and edge guide. The vertical dividers do fit into the same groove. The groove is almost 3/8" so I wasn't concerned about thickness of the tenon. The tenon are a nice tight fit. I cut the tenon a hair to long so the vertical divider has a bit of wiggle vertically, so it looks a bit funny if you get up close to it. Quote
Ryan. Posted July 15, 2017 Author Report Posted July 15, 2017 Made some progress today, got the panels cut and test fitted for the front and back assemblies. Hoping to start the glue up if these this coming weekend, fingers crossed. Got the material for the sides planed. More tenons and grooves. Finally got started on the curves for the lower rails. Only got one done today, should be able to get the other three tomorrow. Sent from my Pixel using Tapatalk 2 Quote
prov163 Posted July 15, 2017 Report Posted July 15, 2017 I just started following Ryan. This is looking great. I have a couple of builds coming up that will use frame and panel joinery so this is helpful. Thanks for sharing. Quote
Chet Posted July 15, 2017 Report Posted July 15, 2017 Looks like some good work Ryan, keep it coming! Quote
Popular Post Ryan. Posted July 16, 2017 Author Popular Post Report Posted July 16, 2017 Started with a sightly different project with my 6 year old daughter this morning. Practice build for what will be a birthday gift for her grandfather. Working with a hand saw reminds me why I love my table saw Managed to get a bit more work done today. Not likely to get anything done tomorrow as I will be at the inlaws. Finished shaping the lower rails. Love them curves Everything also got sanded to 220. Put two coats of wiping poly on the panels, they will get final coats with the rest of the chest later. Got the front and back assemblies glued up. Got a wall full of clamps, but only two over 40". So these got clamped one at a time. And assembled. Panels for the sides and the plywood bottom are up next. Sent from my Pixel using Tapatalk 4 Quote
Popular Post Ryan. Posted July 24, 2017 Author Popular Post Report Posted July 24, 2017 Made some progress this weekend. Got the rails cut and sized. Here is the first dry assembly of the chest. Ended up needing to glue 1/4" strips to the sides of the board I had for the side panels. Works out that these are not overly noticable due to grain match and most of the strips being in the grooves. Got the grooves cut into the legs to hold the panels. Cut the bottom panel with the track saw and table saw. Then notched the corners with a jigsaw and speed square. And missed it by that much on the first fit. Finally a full dry assembly of the box. Sent from my Pixel using Tapatalk 7 Quote
Popular Post Ryan. Posted July 25, 2017 Author Popular Post Report Posted July 25, 2017 Quick update from my lunch hour. Got the case sanded and glued up. Need to sand the legs then apply the finish. Sent from my Pixel using Tapatalk 5 Quote
Popular Post Ryan. Posted August 22, 2017 Author Popular Post Report Posted August 22, 2017 Final update, finished the chest about a week ago, just found the five minutes to write the post. I had a 12" wide board that was long enough, so cut two pieces from it. Hasn't cupped yet, so fingers crossed it doesn't long term. Glued and clamped Out of the clamps and after about 3 minutes with the cabinet scrapper. Routed the small 1/4" champher to match the bedroom set And finally finished and in place. Sent from my Pixel using Tapatalk 11 Quote
wdwerker Posted August 22, 2017 Report Posted August 22, 2017 Don't forget to sign it and date it ! Looks great with the bed ! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.