Dhankx Posted August 19, 2017 Author Report Posted August 19, 2017 Putting the new tools together. On the rigid table saw it says don't install the dust chute unless you have dust collection system. Or else you may DIE . I don't want to make the wrong choice here because I don't want to flip it upside down again lol: if if I got a 2 1/2 hose for my shopvac then got a 2 1/2 to 4 connector to connect to the saw, would that work? I was planning on rolling this outside when I used it which I can still do, but it's so dam heavy that at this point I don't know how realistic that rolling is going to be Quote
bleedinblue Posted August 19, 2017 Report Posted August 19, 2017 The dust vac will certainly be better than nothing. I'd do it. I don't know how good of quality the included mobility system is... If it's too hard to roll I would buy an aftermarket mobile base. Table saws are heavy, there's no way around it. Quote
Chet Posted August 19, 2017 Report Posted August 19, 2017 1 hour ago, Dhankx said: On the rigid table saw it says don't install the dust chute unless you have dust collection system. Are you supposed to just leave the bottom open if you don't have dust collection. I would guess they don't want the chute installed if you don't have DC because it may get clogged over time. As mentioned by @bleedinblue above you should be fine with you shop vac, just check the chute regular to make sure there aren't any small piece blocking the opening. Glad to see you finally got a saw. Quote
Art Posted August 19, 2017 Report Posted August 19, 2017 When I first got my table saw and planer, I did what you are considering re: dust collection. I found it a complete pain because even a good sized shop vac will fill up very quickly. I ended up buying a refurbished 1 hp mobile DC that has made life much easier - this is a new one: https://www.kmstools.com/magnum-industrial-1-hp-dust-collector-with-canister-118841 I think I paid about $150... Quote
Dhankx Posted August 19, 2017 Author Report Posted August 19, 2017 Thanks guys I appreciate your quick feedback! I decided I'll go with the shopvac solution and maybe in year or so look at designing a dust collection system based on how it goes. Quote
wtnhighlander Posted August 19, 2017 Report Posted August 19, 2017 I bet you get over the shop vac in less than a year! Especially if you rip much lumber with an actual ripping blade, it makes a ton of curly little shavings that clog up even a 4" hose in no time. 1 Quote
QHC Posted August 20, 2017 Report Posted August 20, 2017 Is this thing really required to go along with it like the site suggests? Saw some comments about needing it https://smile.amazon.com/Wixey-WR510-Digital-Readout-Fractions/dp/B001PTGBSK/ref=pd_bxgy_469_img_3?_encoding=UTF8&pd_rd_i=B001PTGBSK&pd_rd_r=JQAWRXQ70MAZP1MEVC26&pd_rd_w=0pAF7&pd_rd_wg=KFYY5&psc=1&refRID=JQAWRXQ70MAZP1MEVC26 No it isn't Sent from my SM-N920P using Tapatalk Quote
QHC Posted August 20, 2017 Report Posted August 20, 2017 This one. Ridgid 4512 Ridgid 4512, unless you are taking it to job sites, wouldn't buy one of the portable saws ever. Just my opinion. Sent from my SM-N920P using Tapatalk 2 Quote
QHC Posted August 20, 2017 Report Posted August 20, 2017 Guys will disagree with me, but here's what I would do, it'll keep you well under budget too. Powermatic 54A jointer. $1000'ish, but less if you wait for a 10% off sale and they should have one soon. It's got straight knives and is only 6 inch, but the knives are indexed I believe so it shouldn't be so difficult to change the knives when dull. It'll be light enough to put on a mobile base and push around but hefty enough to do work. Ridgid 4512. $600. It looks like it's even got an integrated mobile base now days. It's an entry level contractor saw, but almost everyone has good results from it. It'll be a lot better than a jobsite saw. The Delta from Lowes is comparable, and to use your Amazon card you could buy a Lowes gift card. DeWalt 735, $600. The best lunchbox planer on the market. You could drop down to the 734 for $350'ish and do just fine. That'll put you at roughly $2200, or $1950 if you go with the lesser Dewalt planer. No complaints with this list, but Ridgid's 6" jointer is good too. Sent from my SM-N920P using Tapatalk Quote
Cheeset202 Posted August 20, 2017 Report Posted August 20, 2017 The first thing you are going to upgrade is the 6" jointer, go for the 8" if you can swing it! Quote
bleedinblue Posted August 20, 2017 Report Posted August 20, 2017 7 hours ago, QHC said: No complaints with this list, but Ridgid's 6" jointer is good too. Sent from my SM-N920P using Tapatalk I have the Ridgid jointer and it has served me decently well, but I am one good sale away from upgrading. Quote
Paul Davis Posted October 21, 2017 Report Posted October 21, 2017 On 7/17/2017 at 6:06 AM, Dhankx said: I'm getting my first table saw, have been doing furniture builds and plan to do that for the foreseeable future. Torn on these two choices. Suggestions? https://smile.amazon.com/DEWALT-DWE7491RS-10-Inch-Jobsite-Capacity/dp/B00F2CGXGG/ref=sr_1_3?s=hi&ie=UTF8&qid=1500242489&sr=1-3&keywords=dewalt+table+saw https://smile.amazon.com/dp/B000S5S5CW/ref=psdc_552962_t3_B00F2CGXGG my primary use will be for cutting rough sticks What did you end up getting? I've got upcoming furniture projects and I'm torn between two options, a Dewalt DWE7491RS too and Rockwell RK7241S. Started with like 7 but after a good amount of time reading through reviews, finally trimmed my options down to two when I saw these two at Sawinery's top 3 for 2017. I'm seeing good Dewalt feedbacks here so I'm pretty inclined to get it. Quote
Dhankx Posted October 21, 2017 Author Report Posted October 21, 2017 6 hours ago, Paul Davis said: What did you end up getting? I've got upcoming furniture projects and I'm torn between two options, a Dewalt DWE7491RS too and Rockwell RK7241S. Started with like 7 but after a good amount of time reading through reviews, finally trimmed my options down to two when I saw these two at Sawinery's top 3 for 2017. I'm seeing good Dewalt feedbacks here so I'm pretty inclined to get it. I got the rigid table saw. I have nothing to compare it to but as far as I can tell it's doing a fine job. Out of all the tools it was by far the hardest to put together but the instructions were fine ( unlike the jointer). It's a heavy beast Quote
gee-dub Posted October 21, 2017 Report Posted October 21, 2017 Glad things are moving along for you. Getting familiar with your new tools is a fun time in the shop (or in the driveway). The saying "Safety First" is not a cliche; practice safe habits whatever you are doing and enjoy woodworking for a very long time. Quote
wdwerker Posted October 21, 2017 Report Posted October 21, 2017 A Grrripper Gr-100 push block is a good investment in safety. http://www.ptreeusa.com/tablesaw_push_blocks.html really keeps your fingers safe. Quote
Chet Posted October 21, 2017 Report Posted October 21, 2017 4 hours ago, gee-dub said: Glad things are moving along for you. Getting familiar with your new tools is a fun time in the shop (or in the driveway). The saying "Safety First" is not a cliche; practice safe habits whatever you are doing and enjoy woodworking for a very long time. 1 hour ago, wdwerker said: A Grrripper Gr-100 push block is a good investment in safety. http://www.ptreeusa.com/tablesaw_push_blocks.html really keeps your fingers safe. Yes on both of these. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.