Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Mission Table Lamp

Featured Replies

  • Popular Post

This journal will document making a Mission style table lamp (well actually 5) from a design/plan in Woodsmith magazine Vol. 33/ No. 198. These lamps have four stained glass panels that go into QSWO frames. Just a heads up the woodworking is minimal for this project but I will show the steps to do the woodworking, stained glass, as well as the wiring at the end. One other disclaimer, I consider myself to be a beginner in the stained glass world I have taken three classes this year and done a couple of projects but just basic stuff like these panels.

Minimal stained glass tools are required for this project but you will need the following:

Glass cutter, 100 watt soldering iron, breaker/grozer pliers, running pliers, glass square, 60/40 solder, Flux, 1/4" copper foil tape, a fid, and the glass

First up make yourself a jig. This will be used for cutting and assembly to keep everything square.

59fbe231637d4_MTL1.jpg.302c4455fedca9833d998b8604edf65c.jpg

Mine is made out of a piece of BB 12 x 16" although you don't have to use BB you want it to be as flat as possible so MDF or particle board would be good options as well. I also made a cutting guide out of BB 2 3/8" wide

If your glass isn't square already, square up a 90 degree corner. Then put the glass on your jig shiny side up (you always cut stained glass on the smooth/shiny side)

59fbe232c9900_MTL1a.jpg.eb68970ae03ab5ffde8820bbb74fb781.jpg

Put your cutting guide on and score the glass with your glass cutter. A couple tips here. You are not cutting through the glass just scoring it. If you hear crushing or are seeing little bits braking off under your wheel lighten up you are pushing down to hard. Regardless of cutter style you always pull towards yourself this allows you too see what you're doing and keep nice even pressure.

59fbe2341fc64_MTL1b.jpg.8abb48f291a0b64decea2581c814af8f.jpg

Most cutters have oil reservoirs in them but I was taught to just dip your tip on an oil soaked rag before each cut so I use an old butter dish and dish cloth soaked in oil like this

59fbe238b0022_MTL4.JPG.87f57e55f873993cf75a6ff44019e075.JPG

another tip is to mark your pieces that way they will fit back together with tighter joints when you solder them later

59fbe2353e4ad_MTL1c.JPG.06d23f73d114bd3692d862a6dd3b091e.JPG

once you cut the strips you can use a glass square to do the cross cuts

59fbe23688b8e_MTL2.JPG.c9d95ee9bbc1395f22bba01dbb384a28.JPG

Again dip your cutter in the oil and pull towards you with steady even pressure and NO backing up you only get one shot :) 

59fbe237c4849_MTL3.JPG.f20e8df884c58fac71dc2c4553aa68e3.JPG 

Then use your running pliers to break the glass along your scored line. The center line on the pliers is lined up with your score line then squeeze easy peasy.

59fbe23a31a0f_MTL5.JPG.bca59ffc982f8520577988abff9323e5.JPG

Walla

59fbe23baabdf_MTL6.JPG.81a327c7a5874365fd94005e950e1c40.JPG

Next up we'll foil up some glass, solder it together and start some woodworking.

 

 

I am going to be real interested in this Paul.  This is something I always thought I would like to try.  Not to put any pressure on you but I am counting on good instruction here. :D

This is gonna be a good one. Glass work is one thing that has been on my list to try.

  • Author
10 hours ago, Chet said:

I am going to be real interested in this Paul.  This is something I always thought I would like to try.  Not to put any pressure on you but I am counting on good instruction here. :D

roh roh that's scary LOL.  I think i need to figure out how to add video some of this would be much clearer with a short video.

4 hours ago, Alan G said:

Oh nice....Looking forward to following along!

Why 5?

One for us 4 are Xmas gifts...that may even get done early that would be a first for me. 

2 hours ago, bushwacked said:

oh cool ... learning new things!! 

Thanks

2 hours ago, drzaius said:

... Glass work is one thing that has been on my list to try.

I thought the same thing which is what got me to take a couple of classes and its actually fairly straight forward...well until you get into curved work then the complexities and tool costs go up pretty quickly. I am looking forward to adding it to more projects as I go forward.

  • 1 month later...
  • Author

Well folks I was trying to do some short video's on glass cutting but I have spent way to much time (weeks) on it so I am going to finish the journal, since the lamps are done, and if I can figure it out I will post them at the end.

Now that we have the glass cut we need to add cooper foil tape to the glass because solder will not stick to the glass. You want to make sure the tape sticks so wipe the glass with rubbing alcohol before you start. To foil just center the tape on the glass and wrap around

5a2ab1ee9e2fe_MTL7.jpg.7b679c7dafb7dceec1ce6564eb322dd9.jpg

You will end up with about 3/32" on each side which you then fold down with your hand or a plastic fid. each separate piece needs to be edged with foil. In this pic I am using a fid to lay a full width piece of foil on the face of the piece so when the panel is slid into the wood grove we will still have an 1/8" reveal.

5a2ab1f025edd_MTL7a.jpg.3c5dcab6419815b6e329a03dcfe4f28b.jpg

Again solder will only stick to foil so imperfections like this need to be fixed prior to solder. Its totally fine to just lay a new piece of tape over this one you will never see it once soldered

5a2ab1f160a2a_MTL7b.jpg.94a1f13df3577c00d3e12495a3fc3868.jpg

This panel is ready to solder up

5a2ab1f42ff22_MTL9.JPG.5ac36f2681a33b770b5a80d6fc36b550.JPG

Now we are ready to solder so this panel. I wanted to tack it together so I fluxed some spots with an acid brush

5a2ab1f5ac9ca_MTL10.jpg.6039daaaa12f29762470f3d43c94d75b.jpg 

And then tack it together

5a2ab1f72c693_MTL11.jpg.f95b7b1230512178c5d9c4b53ade66d7.jpg

Once tacked together add flux to all of the foil tape and solder away. I use a Weller soldering iron made for stained glass. The goal is to get solder on all of the tape front and back and then smooth it out and make sure you don't have any large bumps that will keep the panel from fitting in the wood groove.

5a2ab1f882e35_MTL12.jpg.0dc15254768b3d9aefa125707a6accce.jpg

Rinse and repeat in my case I am doing 5 lamps so this took a while. The soldering is quick the taping is slow :)

5a2ab1fa2231d_MTL13.jpg.68d5bb115a1c085777bb6416c62746a0.jpg

We will patina these panels later but next up we move on to some wood working...

 

So with the three classes that you took, did that give you most of the knowledge that you need and now it just a matter of repetition for what you want to do, or are there additional classes that you want to take.

  • Author
31 minutes ago, Chet said:

So with the three classes that you took, did that give you most of the knowledge that you need and now it just a matter of repetition for what you want to do, or are there additional classes that you want to take.

I do in fact one on foil tape and one on lead panels would cover about 99% of all the projects I would ever use in my work. I am taking a Lamp shade class in January but for wood working panels foil tape or lead are the two options. For doors and larger panels lead and for smaller panels like these lamps foil tape.

 

That's very cool. I love the look of the foil & solder. How much care do you have to take not to crack the glass with the heat?

  • Author

Ok lets mill up some white oak

This chunk should be enough for 5 lamps

5a2ae1726328a_MTL14.jpg.940e66224a96267dc7580ec7a5b2e3f9.jpg

Time to mill...

5a2ae1741984e_MTL15.jpg.f0ec72e9dd761e89d3675b79f8c185e7.jpg

and then resaw...

5a2ae175adec8_MTL16.jpg.0e6c8e1ce9eba4c9c429f3ef4846dd9c.jpg

rest and acclimatize ...

5a2ae17c2ab37_MTL17.jpg.8520b0477213d7ee88248e8a65f05290.jpg

Re mill and finally sand...

5a2ae18241b8e_MTL18.jpg.b05261eb3acb12a452463ffba5299005.jpg 

Out of this plank we will make the feet as well as some trim later in the project, first up make some feet by cutting to size 20 blanks

5a2ae183915de_MTL19.jpg.ce439655a9545a011fdfb5ba8ba88c1f.jpg

Next up I put a small detail on the bottom edge using the TS. You want to make sure you use a new sacrificial fence so there is no chance the feet can move as they pass over the blade. All four edges get the treatment

5a2ae1850adb2_MTL20.jpg.241c2e669e0df161e3434972ca4639f4.jpg

Next I will put a small bevel on the top side with a hand plane

5a2ae188f15dc_MTL23.jpg.50a34fbd7299f635fedde169506973b6.jpg

20 feet complete

5a2ae18cb6797_MTL24.jpg.ef68dba9d218a343b2d7875188700b1b.jpg

Then I rough milled the blanks for the top and bottom caps of the lamp

5a2ae19152285_MTL25.jpg.833b3db0cc0c33f3152527d326f095fb.jpg

Next up grooves and lots of 45 degree cuts...

 

  • Author
21 minutes ago, drzaius said:

That's very cool. I love the look of the foil & solder. How much care do you have to take not to crack the glass with the heat?

Thanks! Not much (none) that may be because I am new and just haven't had an issue yet. The solder melts and flows so fast I think you would have a real mess before you would real the glass. I will say on lead caming you have to be careful it will melt through it pretty quick but again long before the glass would heat up.

Very Interesting build !  It's surprisingly hard to find a picture of the complete lamp without buying the issue.  I am guessing a lighted stain glass body with a normal shade on top ? The pyramidal wood framed stained glass shades really interest me. 

  • Author
34 minutes ago, wdwerker said:

Very Interesting build !  It's surprisingly hard to find a picture of the complete lamp without buying the issue.  I am guessing a lighted stain glass body with a normal shade on top ? The pyramidal wood framed stained glass shades really interest me. 

Should have the rest of the build up yet today so you can see the finished project. The class I am taking next month is on glass lamp shades so there may be a another lamp journal in the not to distant future on that process as well.

On with the build...

First up layout the parts for each cap and mark for grooves to hold the 1/4" plywood

5a2af3e43090f_MTL26.jpg.e58855569e56fd4d6d2ec26f89d22462.jpg

Then at the table saw cut the grove in two passes insuring its centered and the plywood fits

5a2af3e6d185e_MTL27.jpg.8cb2566a99d522b9d41ee37c67e556c6.jpg

Then I cut a bevel on each piece

5a2af3e8687ea_MTL28.jpg.e63184d888930d9de0523c20adf12311.jpg

Lots of parts

5a2af3eb726f2_MTL29.jpg.b2198bd12794f8974ffc74486877e6b4.jpg

Next I cut 45 degree cuts on all corners (which I didn't get a picture of) using my Incra miter gauge set at 45 in each direction to get both cuts on each piece. I used a stop block to insure all the cuts were accurate and then cleaned them up on my shooting board

5a2af3ed5cabe_MTL30.jpg.ac1d74d9690b5e17725cc7dd9bfd18fe.jpg

all the parts through that step

5a2af3f1208af_MTL32.jpg.50bdc4a6982942d8f83485c1fdd708ec.jpg

test fit

5a2af3ef25bbb_MTL31.jpg.ea992d128e1a9abe329804f58e9e4029.jpg

Now I use a dado stack and miter gauge with a stop block to cut a 1/2" dado in each 45 degree corner to make a square mortise when glued up

5a2af3f51ce9a_MTL35.jpg.d864e95bda59576220c5aea80111f53e.jpg

Like so

5a2af3f6b6767_MTL36.jpg.fa741904ab328d76e21d877c23a2e355.jpg

I drilled five 1/2" holes in the plywood pieces for air as well as wiring and fixtures

5a2af3f85a57a_MTL37.jpg.d269532d7b45d2308cea19d316ec491a.jpg

and then prepared them for glue up

5a2af3fa51aea_MTL38.jpg.f1ed31eba359d4f66930508fb49294d7.jpg

I also made the glass frame pieces but apparently didn't take any pics of that. They are 3/4" square with 1/8" deep grooves for the glass and small champers on the outer edges. Here I am gluing things up (the tops get screwed down bottoms are glued on.) Pay close attn to all the grain so that the feet are match each other on each side as well as the caps and risers.

5a2af6f427a9f_MTL43.jpg.b38ffcb78b7c5565e10fa181981121c8.jpg

Next up trim finish and wiring

  • Author
  • Popular Post
16 minutes ago, wdwerker said:

My miter trimmer does a good job but one of these days I've got to build a shooting board & get a left handed plane for it .

I've never used one of the trimmers but have seen them used, pretty cool! I purchased a LV gift card on Cyber Monday that I am using for a dedicated shooting plane I have wanted for a long time. Although a one trick pony I have tried it at a couple different shows and they are really nice.

 

Once glued up I used the same fume/shellac/Waterlox process that I used on my side table build that I had a journal on earlier this fall.

Every one in the ammonia fuming tent for four hours

5a2b00dd40a27_MTL44.jpg.0d981734dde9eaebbae2a6ff7051f3a9.jpg

After fuming I let them sit for a day and then add a coat of garnet shellac and 3 coats of waterlox. Probably should have gone with white oak ply but I really didn't want to purchase a 4x8 sheet for the litlle bit I needed for this project and since they will not be seen red oak scraps will have to do.

5a2b00de93648_MTL45.jpg.4378d9080b0c00b5266e2bfec108782b.jpg

Next up I added black patina to the panels. Super simple just wipe on, let sit for a little bit (a minute or so) and touch up any light spots.

5a2b00dfd6421_MTL46.jpg.47ed4ad75410aae1da2febb8858a22e3.jpg

5a2b00e1412da_MTL47.jpg.8a42003a84c89e01674016bcaaf897f0.jpg

5a2b00e2d0569_MTL48.jpg.bf559ca9c95f7194d70081ae8783bad5.jpg

Then rinse off under water and set aside to dry.

5a2b00e44855e_MTL49.jpg.849c75faeac94e9b2ea73388d1af05e9.jpg

Now with the panels done some quick wiring and put it all together. The wiring is pretty straight forward 3way switch so you can have either the bottom, top, or both lights on.

5a2b04ad90bec_MTL54.jpg.8ac18e5671e4bb275f82e86af09b787b.jpg

5a2b04af22123_MTL55.jpg.ec82d74d9dea37b1cf097317dbf1bcd1.jpg

...and that's it

5a2b00e5e2785_MTL50.jpg.414e683be10db439d1372b2510502d28.jpg

need to adjust to adjust my bulbs wattage's but you get the idea

5a2b00e79e8b8_MTL51.jpg.009090e4833779e7fc5570afd31229db.jpg

...and now 4 out of 5 are complete just need to pick up some glass I ordered to finish the last one. This will be the first time in a long time I have my xmas gifts done early.

5a2b00e98f573_MTL52.jpg.c34886008947f3afb4c6a59e1cb69bb0.jpg

The darker one is for my wife and it will have a black lamp shade same, in the same style as the one shown.

5a2b00eb6a6d3_MTL53.jpg.ad8cd354cc73e7655a0473fab02bf34e.jpg

  • Author
4 hours ago, wdwerker said:

Nice, very nice !

Those will make wonderful presents .

Thanks Steve! 

I like the looks of them a lot. Nice looking work. 

Those are darn nice. Great job! The darker one, do you have a pic of it plugged in?

Oh, and thanks for the journal! 

Those look awesome. I really like the dark one is that red and black? I feel like i just went through a whirlwind of a project. It took you weeks but not on my end.

Have you ever checked out that stained glass shop in Anoka?

  • Author
1 hour ago, mat60 said:

I like the looks of them a lot. Nice looking work. 

Thanks!

1 hour ago, K Cooper said:

Those are darn nice. Great job! The darker one, do you have a pic of it plugged in?

Oh, and thanks for the journal! 

Thanks Coop!! Yes I will get some pics of the darker one plugged in posted tomorrow afternoon.

18 minutes ago, Chestnut said:

Those look awesome. I really like the dark one is that red and black? I feel like i just went through a whirlwind of a project. It took you weeks but not on my end.

Have you ever checked out that stained glass shop in Anoka?

Thanks Chestnut!! Downhome Stained Glass? Yes Paula and Steve are awesome that's where I took my classes. Picking up the glass for the last lamp there tomorrow.

9 hours ago, pkinneb said:

Thanks Chestnut!! Downhome Stained Glass? Yes Paula and Steve are awesome that's where I took my classes. Picking up the glass for the last lamp there tomorrow.

That's awesome. I worked on a project along main street and saw that place sitting there many times. It always interested me but I've never really had the time to pick up something new. Some day I'll have to give it a more serious look. I really like the lamp that you've built.

15 hours ago, pkinneb said:

I purchased a LV gift card on Cyber Monday that I am using for a dedicated shooting plane I have wanted for a long time. Although a one trick pony I have tried it at a couple different shows and they are really nice.

You are right that they are a one trick pony. However.....

A member of our local guild was selling his. I had always wanted one so i jumped on it. I am so glad I did. I built a quick and simple shooting board and have used it a ton. Not a totally necessary tool (being fully dedicated to the shooting board) but one that I have used a lot. You won't regret it. Next up is to add miter trimming ability to my shooting board.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.