Popular Post pkinneb Posted November 3, 2017 Popular Post Report Posted November 3, 2017 This journal will document making a Mission style table lamp (well actually 5) from a design/plan in Woodsmith magazine Vol. 33/ No. 198. These lamps have four stained glass panels that go into QSWO frames. Just a heads up the woodworking is minimal for this project but I will show the steps to do the woodworking, stained glass, as well as the wiring at the end. One other disclaimer, I consider myself to be a beginner in the stained glass world I have taken three classes this year and done a couple of projects but just basic stuff like these panels. Minimal stained glass tools are required for this project but you will need the following: Glass cutter, 100 watt soldering iron, breaker/grozer pliers, running pliers, glass square, 60/40 solder, Flux, 1/4" copper foil tape, a fid, and the glass First up make yourself a jig. This will be used for cutting and assembly to keep everything square. Mine is made out of a piece of BB 12 x 16" although you don't have to use BB you want it to be as flat as possible so MDF or particle board would be good options as well. I also made a cutting guide out of BB 2 3/8" wide If your glass isn't square already, square up a 90 degree corner. Then put the glass on your jig shiny side up (you always cut stained glass on the smooth/shiny side) Put your cutting guide on and score the glass with your glass cutter. A couple tips here. You are not cutting through the glass just scoring it. If you hear crushing or are seeing little bits braking off under your wheel lighten up you are pushing down to hard. Regardless of cutter style you always pull towards yourself this allows you too see what you're doing and keep nice even pressure. Most cutters have oil reservoirs in them but I was taught to just dip your tip on an oil soaked rag before each cut so I use an old butter dish and dish cloth soaked in oil like this another tip is to mark your pieces that way they will fit back together with tighter joints when you solder them later once you cut the strips you can use a glass square to do the cross cuts Again dip your cutter in the oil and pull towards you with steady even pressure and NO backing up you only get one shot Then use your running pliers to break the glass along your scored line. The center line on the pliers is lined up with your score line then squeeze easy peasy. Walla Next up we'll foil up some glass, solder it together and start some woodworking. 3 Quote
Chet Posted November 3, 2017 Report Posted November 3, 2017 I am going to be real interested in this Paul. This is something I always thought I would like to try. Not to put any pressure on you but I am counting on good instruction here. 1 Quote
Alan G Posted November 3, 2017 Report Posted November 3, 2017 Oh nice....Looking forward to following along! Why 5? 1 Quote
bushwacked Posted November 3, 2017 Report Posted November 3, 2017 oh cool ... learning new things!! 1 Quote
drzaius Posted November 3, 2017 Report Posted November 3, 2017 This is gonna be a good one. Glass work is one thing that has been on my list to try. 1 Quote
pkinneb Posted November 3, 2017 Author Report Posted November 3, 2017 10 hours ago, Chet said: I am going to be real interested in this Paul. This is something I always thought I would like to try. Not to put any pressure on you but I am counting on good instruction here. roh roh that's scary LOL. I think i need to figure out how to add video some of this would be much clearer with a short video. 4 hours ago, Alan G said: Oh nice....Looking forward to following along! Why 5? One for us 4 are Xmas gifts...that may even get done early that would be a first for me. 2 hours ago, bushwacked said: oh cool ... learning new things!! Thanks 2 hours ago, drzaius said: ... Glass work is one thing that has been on my list to try. I thought the same thing which is what got me to take a couple of classes and its actually fairly straight forward...well until you get into curved work then the complexities and tool costs go up pretty quickly. I am looking forward to adding it to more projects as I go forward. Quote
pkinneb Posted December 8, 2017 Author Report Posted December 8, 2017 Well folks I was trying to do some short video's on glass cutting but I have spent way to much time (weeks) on it so I am going to finish the journal, since the lamps are done, and if I can figure it out I will post them at the end. Now that we have the glass cut we need to add cooper foil tape to the glass because solder will not stick to the glass. You want to make sure the tape sticks so wipe the glass with rubbing alcohol before you start. To foil just center the tape on the glass and wrap around You will end up with about 3/32" on each side which you then fold down with your hand or a plastic fid. each separate piece needs to be edged with foil. In this pic I am using a fid to lay a full width piece of foil on the face of the piece so when the panel is slid into the wood grove we will still have an 1/8" reveal. Again solder will only stick to foil so imperfections like this need to be fixed prior to solder. Its totally fine to just lay a new piece of tape over this one you will never see it once soldered This panel is ready to solder up Now we are ready to solder so this panel. I wanted to tack it together so I fluxed some spots with an acid brush And then tack it together Once tacked together add flux to all of the foil tape and solder away. I use a Weller soldering iron made for stained glass. The goal is to get solder on all of the tape front and back and then smooth it out and make sure you don't have any large bumps that will keep the panel from fitting in the wood groove. Rinse and repeat in my case I am doing 5 lamps so this took a while. The soldering is quick the taping is slow We will patina these panels later but next up we move on to some wood working... 2 Quote
Chet Posted December 8, 2017 Report Posted December 8, 2017 So with the three classes that you took, did that give you most of the knowledge that you need and now it just a matter of repetition for what you want to do, or are there additional classes that you want to take. Quote
pkinneb Posted December 8, 2017 Author Report Posted December 8, 2017 31 minutes ago, Chet said: So with the three classes that you took, did that give you most of the knowledge that you need and now it just a matter of repetition for what you want to do, or are there additional classes that you want to take. I do in fact one on foil tape and one on lead panels would cover about 99% of all the projects I would ever use in my work. I am taking a Lamp shade class in January but for wood working panels foil tape or lead are the two options. For doors and larger panels lead and for smaller panels like these lamps foil tape. Quote
drzaius Posted December 8, 2017 Report Posted December 8, 2017 That's very cool. I love the look of the foil & solder. How much care do you have to take not to crack the glass with the heat? Quote
pkinneb Posted December 8, 2017 Author Report Posted December 8, 2017 Ok lets mill up some white oak This chunk should be enough for 5 lamps Time to mill... and then resaw... rest and acclimatize ... Re mill and finally sand... Out of this plank we will make the feet as well as some trim later in the project, first up make some feet by cutting to size 20 blanks Next up I put a small detail on the bottom edge using the TS. You want to make sure you use a new sacrificial fence so there is no chance the feet can move as they pass over the blade. All four edges get the treatment Next I will put a small bevel on the top side with a hand plane 20 feet complete Then I rough milled the blanks for the top and bottom caps of the lamp Next up grooves and lots of 45 degree cuts... 1 Quote
pkinneb Posted December 8, 2017 Author Report Posted December 8, 2017 21 minutes ago, drzaius said: That's very cool. I love the look of the foil & solder. How much care do you have to take not to crack the glass with the heat? Thanks! Not much (none) that may be because I am new and just haven't had an issue yet. The solder melts and flows so fast I think you would have a real mess before you would real the glass. I will say on lead caming you have to be careful it will melt through it pretty quick but again long before the glass would heat up. Quote
wdwerker Posted December 8, 2017 Report Posted December 8, 2017 Very Interesting build ! It's surprisingly hard to find a picture of the complete lamp without buying the issue. I am guessing a lighted stain glass body with a normal shade on top ? The pyramidal wood framed stained glass shades really interest me. Quote
pkinneb Posted December 8, 2017 Author Report Posted December 8, 2017 34 minutes ago, wdwerker said: Very Interesting build ! It's surprisingly hard to find a picture of the complete lamp without buying the issue. I am guessing a lighted stain glass body with a normal shade on top ? The pyramidal wood framed stained glass shades really interest me. Should have the rest of the build up yet today so you can see the finished project. The class I am taking next month is on glass lamp shades so there may be a another lamp journal in the not to distant future on that process as well. On with the build... First up layout the parts for each cap and mark for grooves to hold the 1/4" plywood Then at the table saw cut the grove in two passes insuring its centered and the plywood fits Then I cut a bevel on each piece Lots of parts Next I cut 45 degree cuts on all corners (which I didn't get a picture of) using my Incra miter gauge set at 45 in each direction to get both cuts on each piece. I used a stop block to insure all the cuts were accurate and then cleaned them up on my shooting board all the parts through that step test fit Now I use a dado stack and miter gauge with a stop block to cut a 1/2" dado in each 45 degree corner to make a square mortise when glued up Like so I drilled five 1/2" holes in the plywood pieces for air as well as wiring and fixtures and then prepared them for glue up I also made the glass frame pieces but apparently didn't take any pics of that. They are 3/4" square with 1/8" deep grooves for the glass and small champers on the outer edges. Here I am gluing things up (the tops get screwed down bottoms are glued on.) Pay close attn to all the grain so that the feet are match each other on each side as well as the caps and risers. Next up trim finish and wiring 2 Quote
wdwerker Posted December 8, 2017 Report Posted December 8, 2017 My miter trimmer does a good job but one of these days I've got to build a shooting board & get a left handed plane for it . Quote
Popular Post pkinneb Posted December 8, 2017 Author Popular Post Report Posted December 8, 2017 16 minutes ago, wdwerker said: My miter trimmer does a good job but one of these days I've got to build a shooting board & get a left handed plane for it . I've never used one of the trimmers but have seen them used, pretty cool! I purchased a LV gift card on Cyber Monday that I am using for a dedicated shooting plane I have wanted for a long time. Although a one trick pony I have tried it at a couple different shows and they are really nice. Once glued up I used the same fume/shellac/Waterlox process that I used on my side table build that I had a journal on earlier this fall. Every one in the ammonia fuming tent for four hours After fuming I let them sit for a day and then add a coat of garnet shellac and 3 coats of waterlox. Probably should have gone with white oak ply but I really didn't want to purchase a 4x8 sheet for the litlle bit I needed for this project and since they will not be seen red oak scraps will have to do. Next up I added black patina to the panels. Super simple just wipe on, let sit for a little bit (a minute or so) and touch up any light spots. Then rinse off under water and set aside to dry. Now with the panels done some quick wiring and put it all together. The wiring is pretty straight forward 3way switch so you can have either the bottom, top, or both lights on. ...and that's it need to adjust to adjust my bulbs wattage's but you get the idea ...and now 4 out of 5 are complete just need to pick up some glass I ordered to finish the last one. This will be the first time in a long time I have my xmas gifts done early. The darker one is for my wife and it will have a black lamp shade same, in the same style as the one shown. 6 Quote
wdwerker Posted December 8, 2017 Report Posted December 8, 2017 Nice, very nice ! Those will make wonderful presents . Quote
pkinneb Posted December 9, 2017 Author Report Posted December 9, 2017 4 hours ago, wdwerker said: Nice, very nice ! Those will make wonderful presents . Thanks Steve! Quote
mat60 Posted December 9, 2017 Report Posted December 9, 2017 I like the looks of them a lot. Nice looking work. Quote
Coop Posted December 9, 2017 Report Posted December 9, 2017 Those are darn nice. Great job! The darker one, do you have a pic of it plugged in? Oh, and thanks for the journal! Quote
Chestnut Posted December 9, 2017 Report Posted December 9, 2017 Those look awesome. I really like the dark one is that red and black? I feel like i just went through a whirlwind of a project. It took you weeks but not on my end. Have you ever checked out that stained glass shop in Anoka? Quote
pkinneb Posted December 9, 2017 Author Report Posted December 9, 2017 1 hour ago, mat60 said: I like the looks of them a lot. Nice looking work. Thanks! 1 hour ago, K Cooper said: Those are darn nice. Great job! The darker one, do you have a pic of it plugged in? Oh, and thanks for the journal! Thanks Coop!! Yes I will get some pics of the darker one plugged in posted tomorrow afternoon. 18 minutes ago, Chestnut said: Those look awesome. I really like the dark one is that red and black? I feel like i just went through a whirlwind of a project. It took you weeks but not on my end. Have you ever checked out that stained glass shop in Anoka? Thanks Chestnut!! Downhome Stained Glass? Yes Paula and Steve are awesome that's where I took my classes. Picking up the glass for the last lamp there tomorrow. Quote
Chet Posted December 9, 2017 Report Posted December 9, 2017 Thanks for the journal Paul. You did a great job on the lamps and in sharing the process. I really like how they look. Quote
Chestnut Posted December 9, 2017 Report Posted December 9, 2017 9 hours ago, pkinneb said: Thanks Chestnut!! Downhome Stained Glass? Yes Paula and Steve are awesome that's where I took my classes. Picking up the glass for the last lamp there tomorrow. That's awesome. I worked on a project along main street and saw that place sitting there many times. It always interested me but I've never really had the time to pick up something new. Some day I'll have to give it a more serious look. I really like the lamp that you've built. Quote
Alan G Posted December 9, 2017 Report Posted December 9, 2017 15 hours ago, pkinneb said: I purchased a LV gift card on Cyber Monday that I am using for a dedicated shooting plane I have wanted for a long time. Although a one trick pony I have tried it at a couple different shows and they are really nice. You are right that they are a one trick pony. However..... A member of our local guild was selling his. I had always wanted one so i jumped on it. I am so glad I did. I built a quick and simple shooting board and have used it a ton. Not a totally necessary tool (being fully dedicated to the shooting board) but one that I have used a lot. You won't regret it. Next up is to add miter trimming ability to my shooting board. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.