Tom King Posted September 3, 2018 Report Posted September 3, 2018 Of all the different jobs I do, in building houses, sheetrock ranks near the bottom on fun to do. The reasons I do it myself overlap the reasons I do almost everything myself. Those reasons are: 1. I'd have to spend time finding someone else to do it, wait for them to come-which puts a crimp in putting work behind me every day 2. I'd have to pay them, and loose money for lost time in the process, with lost time usually amounting to more loss than whatever I would pay them 3. They're not going to do as good of a job as I am, and not as fast, with so little mess made. The name of the game in building for a living is efficiency. Over the 33 years that I built houses, the last 32 I did it myself. As with most other types of jobs that I do, I've developed my own methods. To start with, here is a picture of all the tools needed for taping, and spreading joint compound. A flexible 6 inch taping knife-a Hyde I think, but the name was worn off the handle decades ago, so I could be wrong. A sponge. A 20" cement finishing trowel kept only for sheetrock, a corner trowel, and a hawk. Most of the time sheetrock takes is the careful handling getting it into the room, and into place, with tight joints. Avoid butt joints at all costs, as much as possible. A little extra time being particular hanging it, pays big dividends in return during finishing. Avoid any kind of joint above, or below the edges of windows, and doors. I see it hung with butt joints on both sides of the top of a door opening, and I can only walk away shaking my head. You couldn't pay me double to finish a room with it hung like that. Hanging it doesn't have to take THAT long to do it correctly, but it's certainly not a time to try to save a few minutes. Normally, I do horizontal taped joints whenever it's best, but the end walls in this room are covered with tall windows, so I chose vertical short joints above, and below the windows, as you can see in the picture behind the tools. The long edges of sheetrock are tapered (indented some). The ends are not. Because the ends are not tapered, there is no way to put it on a flat wall, and not have a hump at that joint-we call that a butt joint. When I framed my houses, I'd put two studs together at the butt joint, and run them down so they were indented 3/32" in from the wall plane. This allowed me to finish a perfectly flat wall. Only use paper tape. Forget the stick-on mesh tape. Paper tape needs to be seated into a bed of joint compound (we'll call that "mud" from here). It's easily possible to squeeze too mush mud out from under the tape, which might not show up soon, but will later. The reason for the flexible knife is so you can put a layer of mud in the joint, stick tape over it, and seat it into the mud enough to leave the tape below the plane of the sheetrock outside the tapered edges. You don't have to push hard, but knowing how hard saves a Lot of time. Some people mix various things with the mud, and stir it various ways. I haven't bothered with that in years. I use it right out of the bucket. It will have bubbles in it when you put it on the hawk, and when you first apply it to the wall, but the second stroke with the knife smooths it right out. In the corners, after putting some mud right in the inside peak of the corner, fold the tape lengthwise along the crease, and stick it in place lightly, just so it will stay there. One pass of the corner trowel seats it. Put more mud on top, and one more pass of the corner trowel. The important thing with the first coat is that no mud, and certainly no tape is sticking up past the finished plane of the wall. The long cement finishing trowel is to smooth out the taped seams. You can hold it tight to the sheetrock outside the tapered part, smoothing out the mud the best you can, but don't worry about making it perfect at this point. It will show you if you need to squeeze in the tape anywhere with the smaller knife. Once all that is dry the next day, I take a bucket, and sponge, and wipe off any high parts. Once you are sure nothing is protruding, my next step is different than you might see anyone else do. I bring the airless spray rig in the room, and spray a coat of water based primer on it. Mud will stick fine to the primer. The dry mud, before the primer is put on, will shrink, so you know that it's below the surface after the primer is on. If you look in the background, behind the tools in the picture, you will see a vertical tapered joint, and the corner, with the next coat of mud on them. That second coat will probably be enough for most of it, but there will probably be some more touchups. For putting the second coat of mud over the screwheads in the field, and over the taped joints, a light is clamped to the hawk, and shines directly against, and across the wall. You can see a knat on the wall with this, and any imperfection, or low spot that needs to be hit with mud is illuminated. They only need a thin coat at this point. My help wasn't working today, so I went over this morning by myself, and spent maybe a half hour putting the last coat on. That's when I decided to take these pictures. The primer makes it easy to see any imperfection (we always go for perfection), and prevents any possibility of scuffing up the paper on the face of the sheetrock. I try to do as little sanding as possible, but I want to do absolutely no sanding on the paper face of the sheetrock, for several reasons. Even if I didn't have the airless sprayer, I'd roll on primer at the same stage. With the airless rig, and a couple of different tip extensions, it's about a 5 minute job to spray a room this size. Don't try to save mud. Any not put on the wall, and whatever is left from scraping on the hawk is discarded, and the knife, and hawk cleaned with the sponge and bucket before more mud is put on the hawk. Cleanliness saves a lot of time, as one foreign thing leaves a streak in the mud, so no chasing of those. This picture shows the second, and hopefully last coat of mud on the wall, on top of the Primer. There is not much of it, as hopefully you can see in the picture. I'll be back with more pictures, and more text later. This is a 13-1/2 foot by 23-1/2 foot room, with a cathedral ceiling. I haven't done sheetrock since I built the last new house in 2007. I number of people who should have known, back then, said I was the best they'd seen. Having done only plastering in old houses since then, I'm a lot better now than I was back then. It took us about 45 minutes to mud, and tape this room for the first coat. The thin streaks on the lower part of the wall were some imperfections in the surface of that particular sheet of sheetrock, that I didn't catch until shining the light on the wall after the primer. I put this coat on as smooth as I can, using the long trowel if I need to. It's hard to do a perfect job without some sanding, so there is a little bit to be done, and I do it with this autobody 24" block, with 150 sandpaper. The autobody sandpaper is so good that one piece stuck to the block easily did the whole room. The whole wall is hit, but it doesn't take long. That leaves us ready to spray the finish coats of paint. Since this room is going to be white semi-gloss, we're going to trim out the windows, and then spray the whole thing in one shot. At first I thought we wouldn't bother with the sanding, but I'm doing this as a favor to a good friend, who has done me a big favor, and when she said semi-gloss it all, a little sanding is required. I'm sure others will have their own way of doing it, but this is my own method that suits me. When we're ready to paint, I'll spray some primer over the bare mud places, and take the pickup of the sprayer out of the primer, and put it right into the paint. Until the line is cleared, I'll just spray what primer is left in it on the walls, rather than taking time to clean the rig between the primer, and paint, since both are water based/bourne. Being both finisher, and painter is what saves most of the time, and it might start to become obvious why I do everything myself. Any questions? 2 Quote
Bankstick Posted September 3, 2018 Report Posted September 3, 2018 DIY and make sure it is done right. I sold factory and custom cabinetry along with lighting for 2-1/2 years. Want to pass this along FWIW. The co-owner was in a new construction to measure for cabinets. The contractor had run a sting along the kitchen walls about countertop height. He was building up the low places with strips of cardboard to match the string. Patrick asked what he was doing. He replied that the sheetrock would be straight along the backsplash and wouldn't have gaps between the backsplash and the sheetrock. Smart or what? Quote
..Kev Posted September 4, 2018 Report Posted September 4, 2018 I've found a wet sponge to be way better than sanding. Not as messy and does a great job. Regardless of the method, it's the results that count I suppose. 1 Quote
pkinneb Posted September 4, 2018 Report Posted September 4, 2018 I have to say this is one job I always hire out in fact I am looking for a taper as we speak to do the majority of my basement. Having said that thanks for posting the info as I will be doing the home theater room. I do not want someone coming in and messing up all the effort I am putting in for soundproofing in that room. Quote
wtnhighlander Posted September 4, 2018 Report Posted September 4, 2018 I'm with Kev on the wet sponge sanding method, for small repairs, at least. Seems pretty slow for a full room or house, though. Quote
Tom King Posted September 4, 2018 Author Report Posted September 4, 2018 Maybe I wasn't clear about the sponge. There was no sanding of the mud. No matter how hard you push on the knifes, edges will still have some thickness to them. The amount of time that sponging takes is directly dependent on how well the mud is spread to start with. You don't want to leave it high anywhere to have to take down any thickness. A sponge might be a tad slower than sanding, but there is no cleanup, and no respirator required. That's not dust on the floor at the bottom of the wall, on the floor. It's from spraying the primer. The floor hasn't been cleaned in the process. The edges of the joints, and corner that you can see behind the tools, will get sponged, but nothing else will need it. It won't take long at all, as it's just blending in, rather than taking down. Another thing the primer does is seal the first coat of mud. Even after it's dry on the wall, if it gets wet again, it will swell. The primer eliminates that swelling. If you put a second coat of mud on top of the first, the first coat will swell again too, from the water in the second coat. It also eliminates little balls of paper fuzz getting into the mud, which leaves streaks. Any sanding on the paper also leaves paper lint. If you leave the first coat on the taped joints level, with the long trowel, it will leave a slight indentation after it dries. The primer locks it there for further work, so the total shrinking from there out will be minimal, so the second coat won't really shrink to amount to much, and will be enough for the majority of a room. I didn't think that 45 minutes for the first coating, and a half hour for the second was that long, but maybe I was wrong. It didn't seem slow to me. If you leave it built up, so it has to be cut down, any method is slow. The sanding block is after the primer. There might be a place of two on the mud where it needs a little sanding, but nothing to amount to much. If there was any dust anywhere, for whatever reason, there would be a different texture, here and there, from it floating to the top of the primer as it dried. The blocking doesn't take that long either. The 2 foot block going sideways covers fairly quickly, and you don't have to rub over anywhere but once. What took most of the time was moving the stage around to get up in the peaks of the cathedral ceiling. Quote
Tom King Posted September 4, 2018 Author Report Posted September 4, 2018 Bankstick, When I was building houses, and couldn't get lumber that stayed straight after 1992, I started buying bundles of studs, and 2x6's for the house next year (year ahead of time). I have a little building that has a concrete floor, and is covered with 5V tin on the whole outside. Those bundles of lumber waiting for next year are stored in there. We only use the ones that stayed straight for building walls. My friend that built this house had never built one before, so this room needed some help. It was built in front of a part that had plywood left on the outside for several years, so we spent some time flattening that with a power planer. Other parts needed both the power planer, and a broad hatchet. When I was building new houses, I never followed anyone else, and every step was done knowing what was coming later, so there were no walls to straighten before finish work could begin. 1 Quote
Coop Posted September 4, 2018 Report Posted September 4, 2018 Going forward, I’d rather eat at McDonalds than to tape and float. Next time there’s rock to be hung, I’ll let the pros do it. Thanks though for the info. Quote
mat60 Posted September 4, 2018 Report Posted September 4, 2018 My sheetrock looks best after everything goes back in the room. 1 Quote
Tom King Posted September 4, 2018 Author Report Posted September 4, 2018 Coop, Yeah, the only thing that this ranks above in the "No Fun" category, in building, is installing insulation. We're working in an old house with nothing on the walls yet, and won't be insulated. Even with two little 110v air conditioners stuck in windows, it gets really hot in there late in the afternoons these 90 degree days, that seem like they won't quit. This house has a strong AC system, so we go there to do something late on these days. Quote
mat60 Posted September 4, 2018 Report Posted September 4, 2018 All this info helps for next time. The butt joints are something that's been a pain for me along with making a mess. Quote
Chestnut Posted September 4, 2018 Report Posted September 4, 2018 I've avoided butt joints by hanging sheetrock standing vertical. It seems a lot of people thing it's wrong to do it this way but it works really nicely. It's especially nice when rocking houses and rooms that aren't the perfect 8 feet like the house i finished remodeling last year. I agree with the joints around doors. Rock is so cheap i usually plan to have a full sheet cover the hole and then cut the door or window out afterward. That primer pointer is priceless though i'm going to use that in the future. Kind of makes me think "why didn't i think of that". 1 Quote
Bankstick Posted September 4, 2018 Report Posted September 4, 2018 I watched a fellow mud sheetrock in a motel lobby one time in the past. I mentioned something about sanding. He replied that if you have to sand the mud, you are using too much mud. Comments? Quote
Tpt life Posted September 4, 2018 Report Posted September 4, 2018 1 hour ago, Bankstick said: I watched a fellow mud sheetrock in a motel lobby one time in the past. I mentioned something about sanding. He replied that if you have to sand the mud, you are using too much mud. Comments? Add “very much...” Quote
Tom King Posted September 4, 2018 Author Report Posted September 4, 2018 The most important thing about using primer is that you don't want to leave any spot too high under it. You don't want to have to sand through the primer to get the level back where you want it. The stiff cement finishing trowel lets you tool the taped joints leaving the surface of the mud in the tapered edges flush with the surface of the sheetrock. Tool it level, and it will shrink a little bit anyway. Absolutely, don't risk leaving anything high thinking it will shrink enough! Once you are sure nothing is too high, then the primer can be applied. There should be no reason to require any sanding before primer. If the cement finishing trowel exposes the paper tape anywhere when striking the joint with it, use the flexible knife to seat it a little lower, put more mud over it, and strike it again with the long trowel. That trowel should leave a pretty uniform looking joint with no mud outside the recessed part of the tapered edges, and no tape showing anywhere. Once you have the primer over that stage, it leaves very little left to do, and little chance of sanding through the primer to hit the paper. If you should have a damaged part of the paper surface anywhere, in spite of careful handling getting it to, and on the wall, saturate the torn part with yellow glue, let it set, and sand it down. It's almost impossible, and too much trouble to get a good fix on torn paper with just mud. Quote
Tom King Posted September 4, 2018 Author Report Posted September 4, 2018 I forgot to mention primer. Don't use PVA primer-too soft, and gummy. I like this: https://www.sherwin-williams.com/homeowners/products/premium-wall-wood-primer Quote
Tom King Posted September 6, 2018 Author Report Posted September 6, 2018 I looked for a video on youtube to find someone who does it like I do. The first several I watched, I thought someone would need to come put me in one of those white jackets that tie your arms behind your back, because they were painfully slow to watch-about as bad as watching paint dry. I finally found one guy that spreads mud like I do, with the knife sideways. I don't strike the mud before putting the tape on it though, and then it gets spread when I seat the tape with the knife. This doesn't show what he does after bedding the tape. I put a top layer of mud over it, and strike it with the cement finishing trowel. It shouldn't even need much with the sponge after it dries, before shooting a coat of primer. This is just to show the way the guy spreads mud. I prefer a hawk over a tub. The mud I wipe off the wall in the process of seating the tape gets put back on top of the tape, to be spread by the finishing trowel. No good reason to go slower than him. Start at about 3:10. The first few minutes show him mixing mud, and I don't do that. It works fine right out of the bucket. If you add water, it works a little easier, but shrinks more. I just use regular, general purpose drywall compound. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.