Popular Post curlyoak Posted September 3, 2022 Popular Post Report Share Posted September 3, 2022 Sapele face. The cabinets on the bench are reversed. On the left installs on the right. Etc.I have a scribe edge going against masonry. The area feels like inside but there is one open wall to the outside. The cabinets are well protected from the weather. And the finish is high gloss Lush urethane. I recommended sapele for its beauty and weather resistance. The panels are book matched with flat sawn sapele. Between the cabinets will be a beverage refrigerator under counter. A granite counter will go wall to wall over the 2 cabinets and refridgerator. Inside one will have adjustable shelves and the other cabinet will have pull out trays. And 4 drawers on top. Not shown but on the side that is next to the refrigerator has 5" wide piece of sapele on the face edge attached to the plywood. The refrigerator will cover up most of the cabinet side but the front part will be seen. 7 Quote Link to comment Share on other sites More sharing options...
treeslayer Posted September 3, 2022 Report Share Posted September 3, 2022 Those are going to be great looking cabinets 1 Quote Link to comment Share on other sites More sharing options...
curlyoak Posted September 3, 2022 Author Report Share Posted September 3, 2022 At the moment the panels look dull because I sanded the last coat. It will get more varnish later. Above is pre sanded. 1 Quote Link to comment Share on other sites More sharing options...
Popular Post curlyoak Posted September 5, 2022 Author Popular Post Report Share Posted September 5, 2022 This is what Was trying to explain earlier.I used some biscuits for alignment. Just the front of the side will show. The refrigerator hides most of it. 6 Quote Link to comment Share on other sites More sharing options...
Coop Posted September 5, 2022 Report Share Posted September 5, 2022 Great way to do it! 1 Quote Link to comment Share on other sites More sharing options...
Popular Post curlyoak Posted September 9, 2022 Author Popular Post Report Share Posted September 9, 2022 trays are done. Next 4 drawers... 7 Quote Link to comment Share on other sites More sharing options...
gee-dub Posted September 9, 2022 Report Share Posted September 9, 2022 Looking good ! 1 Quote Link to comment Share on other sites More sharing options...
Ronn W Posted September 9, 2022 Report Share Posted September 9, 2022 Nidley done. I like the drawers. 1 Quote Link to comment Share on other sites More sharing options...
curlyoak Posted September 9, 2022 Author Report Share Posted September 9, 2022 On 9/9/2022 at 11:23 AM, Ronn W said: I like the drawers Thanks. Those are trays. There'll be 4 drawers all across the top. And those drawers will go on hold for 2 or 3 days. I need to finish the previous project. Expected and anticipated... Quote Link to comment Share on other sites More sharing options...
Gary Beasley Posted September 10, 2022 Report Share Posted September 10, 2022 On 9/3/2022 at 2:50 PM, curlyoak said: At the moment the panels look dull because I sanded the last coat. It will get more varnish later. Above is pre sanded. Wow, that looks a bit pissed off. I guess it'll be happier with the finish on it. 2 Quote Link to comment Share on other sites More sharing options...
Coop Posted September 12, 2022 Report Share Posted September 12, 2022 On 9/9/2022 at 9:25 AM, curlyoak said: trays are done. Next 4 drawers... Just wondering about the two darker vertical boards on the left side of the left trays? First guess was that they are standoffs to attach the drawer glides to clear the doors but they don’t seem to be attached to the side of the case as there is a space between the two and a shadow. Next guess is that there is a spacer between the two to keep from having to use thicker pieces to attach the glides to? Quote Link to comment Share on other sites More sharing options...
curlyoak Posted September 12, 2022 Author Report Share Posted September 12, 2022 On 9/11/2022 at 10:24 PM, Coop said: Next guess is that there is a spacer between the two to keep from having to use thicker pieces to attach the glides to? That is the guess. One way or another the trays needed to clear the blum hinges on the bottom. 1 Quote Link to comment Share on other sites More sharing options...
Popular Post curlyoak Posted September 16, 2022 Author Popular Post Report Share Posted September 16, 2022 Drawers are done. Cabinet backs and shelves...then a final sanding...then varnish. 7 Quote Link to comment Share on other sites More sharing options...
Popular Post curlyoak Posted September 17, 2022 Author Popular Post Report Share Posted September 17, 2022 Here is the other 3 door panels before 400g sanding and in the door frame. 3 Quote Link to comment Share on other sites More sharing options...
Popular Post curlyoak Posted September 26, 2022 Author Popular Post Report Share Posted September 26, 2022 Next is to install. That will be in a week or so... 5 Quote Link to comment Share on other sites More sharing options...
Popular Post curlyoak Posted September 27, 2022 Author Popular Post Report Share Posted September 27, 2022 The Lust is on the outside 3 coats. The Arm-r-seal is on the inside. 2 coats. 3 Quote Link to comment Share on other sites More sharing options...
Mark J Posted September 27, 2022 Report Share Posted September 27, 2022 Why use the ARS insread of using all Lust? Quote Link to comment Share on other sites More sharing options...
curlyoak Posted September 27, 2022 Author Report Share Posted September 27, 2022 On 9/27/2022 at 9:13 AM, Mark J said: hy use the ARS insread of using all Lust? I wanted a lot of coats on the outside. The quart did that with a little left over. Less exposure inside. The inside took almost all of the ARS. 1 Quote Link to comment Share on other sites More sharing options...
gee-dub Posted September 28, 2022 Report Share Posted September 28, 2022 Oh yeah. Lots of oooh's and ahhh's looking at those beauties. 1 1 Quote Link to comment Share on other sites More sharing options...
Coop Posted October 2, 2022 Report Share Posted October 2, 2022 @curlyoak, how did you fare the storm? And other Floridian members on here? Hope everyone is safe! 1 Quote Link to comment Share on other sites More sharing options...
Popular Post curlyoak Posted October 2, 2022 Author Popular Post Report Share Posted October 2, 2022 On 10/1/2022 at 10:10 PM, Coop said: @curlyoak, how did you fare the storm? And other Floridian members on here? Hope everyone is safe! Thanks for thinking of me and the disaster in Florida. Fortunately for me there was no meaningful issues. In Florida the brunt of the storm was felt by Southwest Florida. I live in Southeast Florida. Naples and Fort Meyers was worst Tampa was bad. There was high storm surges near roofs that took out whole neighborhoods. We had moderate winds and a lot of rain but no meaningful damage. 4 Quote Link to comment Share on other sites More sharing options...
Popular Post curlyoak Posted October 6, 2022 Author Popular Post Report Share Posted October 6, 2022 The hardware. Chosen by client. Installation next... 6 Quote Link to comment Share on other sites More sharing options...
Mark J Posted October 15, 2022 Report Share Posted October 15, 2022 Looks like a face. Quote Link to comment Share on other sites More sharing options...
Popular Post curlyoak Posted October 23, 2022 Author Popular Post Report Share Posted October 23, 2022 Installed. The client is very happy. And that makes me happy! 5 Quote Link to comment Share on other sites More sharing options...
Mark J Posted October 24, 2022 Report Share Posted October 24, 2022 Good job! 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.