Ron Swanson Jr. Posted October 17, 2024 Report Posted October 17, 2024 Wow! Beautiful work!!! 1 Quote
Popular Post pkinneb Posted October 18, 2024 Author Popular Post Report Posted October 18, 2024 Last night I was able to get the second chair arms completed. Now I need to finish the foot rails, corbels, and seat platforms and they will be ready for final finish prep which I hope to start early next week. Re the cushions the fabric, piping, and foam has been ordered but are backordered until 10/25 so a slight delay there. Here is the fabric the boss chose 5 Quote
BillyJack Posted October 19, 2024 Report Posted October 19, 2024 Looks good. I’m more of a vinyl/leather person myself, but I gave up on buying a upholstery machine after I didn’t like the cost.. Did you make more than two? Quote
Popular Post pkinneb Posted October 20, 2024 Author Popular Post Report Posted October 20, 2024 On 10/19/2024 at 10:37 AM, BillyJack said: ...Did you make more than two? No just two. Today I started with the aluminum foot pad. First cutting it to size at the table saw and then routing out the recess at the router table. I have a designated blade but probably not necessary the only thing I don't like is it makes a hell of a mess. With that done I moved onto the seat supports Then I glued the corbels in I did make a quick tenon with the PR for alignment. One piece left under the front of the seats and these will be construction complete, hopefully tomorrow. 7 Quote
roughsawn Posted October 20, 2024 Report Posted October 20, 2024 Love the chairs, but REALLY love the router table. Great thread Paul. I never knew chair building was so involved. 1 Quote
Mark J Posted October 20, 2024 Report Posted October 20, 2024 Looks like you remembered to bypass the brake when you cut the aluminum . Is the cut on the TS much better than you'd get with a hacksaw and file? 1 Quote
pkinneb Posted October 20, 2024 Author Report Posted October 20, 2024 On 10/20/2024 at 8:37 AM, Mark J said: Looks like you remembered to bypass the brake when you cut the aluminum . Is the cut on the TS much better than you'd get with a hacksaw and file? I did but I've seen several video's where its been tested and its pretty rare it would set it off but not worth the chance for me. Yes much better and very quick, its just like cutting wood with the only downside being the mess. After a couple minutes with a shop vac you're all good. 2 Quote
Coop Posted October 21, 2024 Report Posted October 21, 2024 I like the aluminum footrest idea. 1 Quote
Popular Post pkinneb Posted October 21, 2024 Author Popular Post Report Posted October 21, 2024 First up today was to fix a dent a clamp caused ...and just like that good as new Next up I finished the seat supports And with that they are construction complete. Up next the parts will be taped off where needed, dyed ebony. and then sprayed poly top coat before glue up. Once the cushion materials arrive I will begin on those as well. 7 Quote
Mark J Posted October 21, 2024 Report Posted October 21, 2024 You're going to spray before glue up, but will that be with the pieces loose, dry fitted together? Quote
pkinneb Posted October 21, 2024 Author Report Posted October 21, 2024 On 10/21/2024 at 8:54 AM, Mark J said: You're going to spray before glue up, but will that be with the pieces loose, dry fitted together? No, there are a few pieces glued like corbel's to front legs and foot rests to supports other than that everything will come apart be taped off, dyed, and sprayed with poly before final glue up 1 Quote
Popular Post pkinneb Posted October 24, 2024 Author Popular Post Report Posted October 24, 2024 Chair #1 ready for the finish process... 3 Quote
Popular Post pkinneb Posted October 26, 2024 Author Popular Post Report Posted October 26, 2024 First coat of ebony dye ... second coat Next up spray some poly 5 Quote
BillyJack Posted October 27, 2024 Report Posted October 27, 2024 I don’t do mine before assembly. Much easier. But….. nice work.. 1 Quote
Popular Post pkinneb Posted October 28, 2024 Author Popular Post Report Posted October 28, 2024 Found some flaws after dying that needed to be addressed in the top back rail. A few swipes with a card scraper and back to another coat of dye. With that done and dry it was time to spray some poly. Once dry I'll hit it with some 320 and if there is nothing to respray this one will be ready for assembly and then I'll have room to start finishing on the second one. 4 Quote
Popular Post JohnG Posted October 28, 2024 Popular Post Report Posted October 28, 2024 Looking great! Props for fixing the finish flaws. By that point in a project I don’t always have the energy to take the step backward to fix it, but then regret it later. 2 1 Quote
Popular Post pkinneb Posted October 28, 2024 Author Popular Post Report Posted October 28, 2024 On 10/27/2024 at 7:48 PM, JohnG said: Looking great! Props for fixing the finish flaws. By that point in a project I don’t always have the energy to take the step backward to fix it, but then regret it later. Not going to lie I thought about it but being on the back rest knew I had to fix it. It took longer to make the decision to fix it than to actually fix it 4 1 Quote
Popular Post wtnhighlander Posted October 28, 2024 Popular Post Report Posted October 28, 2024 Removing finish to make a repair is one of the most effective uses of a card scraper, IMO. Soooooo much faster than sanding. Can't wait to see how this ebony scheme looks when assembled! 2 1 Quote
Popular Post pkinneb Posted October 30, 2024 Author Popular Post Report Posted October 30, 2024 Glued up the front and back assembly's today Tomorrow I will continue gluing this one up, get chair two taped up, and hopefully start the dye process on it. 4 Quote
wtnhighlander Posted October 30, 2024 Report Posted October 30, 2024 Spraying finish is way outside my experience. Did you use oil-based poly, or water-born? And is thinning necessary to spray? Quote
pkinneb Posted October 30, 2024 Author Report Posted October 30, 2024 On 10/30/2024 at 5:44 AM, wtnhighlander said: Spraying finish is way outside my experience. Did you use oil-based poly, or water-born? And is thinning necessary to spray? I use water based so I can spray it indoors unless the weather permits outdoor spraying. My shop does not have the explosion proof fan you need for oil based as they will explode your wallet LOL. Specifically this is General Finishes High Performance Satin polyurethane (waterbased) thinned 5%. 1 1 Quote
Popular Post BillyJack Posted October 30, 2024 Popular Post Report Posted October 30, 2024 If it’s cool outside I’ll spray inside at shop temp. 75+ and then move them outside till they are slightly touchable, them move back inside. This gives the shop time to get any spray in the air out and then I close the door. If it’s windy outside I’ll spray inside and move outside once I know it’s sealed over.. 3 Quote
BillyJack Posted October 30, 2024 Report Posted October 30, 2024 Kinda irritates me that my daughter wanted the chairs and they could be black to match the table I made her and then her to change her mind at the end and I got stuck with 4 polar chairs. If I knew she would change her mind , I would have made them oak.. 1 Quote
Botch Posted October 30, 2024 Report Posted October 30, 2024 First time I’ve seen this thread; beautiful project! And you said: Quote Probably just me but that router bit is scary just to look at so the quicker I can be done the better and trimming it closer definitely made that process quicker It’s not just you; dayam I didn’t know they made flush trim router bits that big! 1 1 Quote
Popular Post pkinneb Posted October 31, 2024 Author Popular Post Report Posted October 31, 2024 Got the second glue up on this one done just the arm tops to go and this one will be ready for its cushion. Unfortunately the foam is now delayed until 11/15... 4 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.