Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Hanging Hand Tool Cabinet

Featured Replies

  • Popular Post

Started working on my Pekovich designed hand tool cabinet. I'll be using his plans off of FineWoodworking.com with some changes like size, layout, etc

TC1.thumb.JPG.b58beecd203a0888a9344ec964271dac.JPG

First up was to get an idea on dimension's. Using a piece of plywood I started laying things out to get an idea on size and whether or not I would need to alter the plans for my needs. After going through this process I decided to go a couple inches wider and 4" taller then the plans.

Rough idea on the plane till

TC3.thumb.JPG.f0988e565e564054472d42a5e81cf2c7.JPG

I think I will center the till and have swing out saw storage (Cosman design) on the right side and hand drills on the left

TC4.thumb.JPG.cc1136183fd2d5dab81614d7c5235697.JPG

I will also have drawers on both sides not thinking I will need as much hand plane space as the design has.

TC5.thumb.JPG.9310f9560d698efe98d9a4a7149707d2.JPG

The upper portion will house a lot of my chair tools 

TC6.thumb.JPG.3089725a4429d160fb80a3ac371226b6.JPG

TC7.thumb.JPG.711c2611c6251c7c23601c4f50815011.JPG

And the doors will be home to my chisels, rasps, layout tools, etc

TC8.thumb.JPG.f46048d37b845266f9392f4d4a4447f1.JPG

TC9.thumb.JPG.75cd0143b034a07948ca4f9e3ee03886.JPG

Since I do not have any planes that wont fit in the space above the lower plane storage and the till I am going to make that a bit wider like 3 1/2 - 4" and put a set of tambor doors that will meet in the middle...just becuase I have always wanted to make tambor doors but have never had a project that would look good with them :)

With the design laid out it was time to pull out the wood. I have a lot of ash so that's what I'm going to use for this project. It's been in the finish room which is why some of it looks gray LOL

TC10.thumb.JPG.4fcaa5cc80d875eff890e97bf03fd5d4.JPG

 

 

  • Replies 227
  • Views 19.8k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Time to cut some dovetails  First up decide what goes where   With that decided time for some layout. I'll be cutting these DT's at the TS using a blade ground to 7.5 degrees so I need

  • Ok time to cut the pins. I use Mike Pekovich's blue tape trick, it really helps with my bad eyes. First up apply the blue tape to the end of the top and bottom panel ends. Next and the most

  • Today started with the tambour door stop. First up drill a hole in the top side of the case, in the track, for a 1/4" dowel Cut the dowel down and glue it in. With that don

Posted Images

Laying stuff out and trying to figure out where to put it (while still allowing room for future toys) is always the hardest part.

I really like the look of hand tool cabinets and looked longingly at this one when Mike published it.

Looking forward to seeing your progress.

Not that you really can, but have you made any "future proofing"?

  • Author
  • Popular Post
On 3/7/2025 at 8:21 AM, Mark J said:

Not that you really can, but have you made any "future proofing"?

Yes and no. So yes there will be extra space but honestly as I was pulling stuff out I'm like I rarely use that should I keep it? So I have started reevaluating (selling) some stuff...a plane here a spokeshave there... ultimately it will fit my needs...I think :)

Lets cut some stock...

First I cut a straight edge on a couple pieces unfortunately had to do it in the shop as its cold out.

TC11.thumb.JPG.b38b521679a6397f6d0a5d1416fe23bc.JPG

With everything rough milled for the cabinet and doors I let it rest for a few days.

TC13.thumb.JPG.c8d556a9d16d7c2c7a844d83398e324e.JPG

I did need to glue up one panel for the top , bottom, or shelf haven't decided yet

TC12.thumb.JPG.a1bfcb21fbfa9b00d303f8949ed295b4.JPG

After a few days I final milled everything to size

TC15.thumb.JPG.adec24248a1f5adcd9556ddd797d3c38.JPG

TC16.thumb.JPG.ef075c0049c4e9bd6462ad3e4924496d.JPG

Next up we'll cut some dovetails using both power and hand tools.

 

  • Popular Post

This makes me smile and I'm following closely.  

I built my wall-hanging handtool chest maybe 27 years ago.  Before starting I decided to "future-proof" the build by purchasing all the remaining tools I wanted (and I can hear the laughter on the forum!); the main one was a #7 jointer plane, and I spaced out the rest of the back wall based on it.  One swinging door held all my chisels, it had a bit of extra room but it's full now; the other door held all my measuring tools, it still has some open space.  

Looking forward to watching your build!  

This is going to be a cool and envious build! 

Really good stuff. My wall mounted plane till evolved to having two clamshell wings. It is not as attractive as Michael’s but I have enjoyed having it for many years. Making sure you have some flexibility for growth and changes will extend the lifetime. These are fun and exciting builds. I am looking forward to the ride-along. Thanks for taking us along.

  • Author
  • Popular Post

Time to cut some dovetails 

First up decide what goes where  

TC17.thumb.JPG.90361fc3cafc429646406734c44622c2.JPG

With that decided time for some layout. I'll be cutting these DT's at the TS using a blade ground to 7.5 degrees so I need to get that set up as well. I also knocked out a sled for this since the sides are long I used two miter gauges to keep things square.

First up using a marking gauge I marked both ends of the side panels front and back only. I also marked a test piece for blade set up.

TC18.thumb.JPG.b1b4ba2af75c8ca2bf77e5d2e44b5a3c.JPG

TC19.thumb.JPG.bf56c21e591b41613fd8cfddbaff1b47.JPG

With that done I laid out for the tails which will be cut at the TS. I wanted 5 evenly spaced pins so using a mark at the beginning and end I took a ruler and slid it out so 0 was at the first tick and 10 was the last tick then put a mark every 2"s and with that I had 5 evenly spaced tails. Using the marked board I made ticks on the sled this lets me cut them all while only marking one.

TC20.thumb.JPG.ae3d99c03a5a34377419a55afa7b8f8c.JPG

TC21.thumb.JPG.57ed15dbbb0a642c5447b6f5b2e94e6f.JPG

TC22.thumb.JPG.c7b9ad698c7b7f71a89560fc793a4d82.JPG

Rinse and repeat (the door sides had a separate layout but the same process as the case sides)

TC23.thumb.JPG.d6c87dbafdec22789ce0d9a307458874.JPG

Next up was to clean up the tails. first I used a fret saw to cut the majority of the waste and then used a chisel to clean them up.

TC24.thumb.JPG.be2e8d762bf27488d1c66fc19dd09385.JPG

TC25.thumb.JPG.dae40d7be59a795717beace0288986aa.JPG

TC26.thumb.JPG.4768543edbecceaa8fd1e84d0fe15cda.JPG

TC27.thumb.JPG.d75da951ea8c97eb303c5c4cad305ab3.JPG

Next up I'll be working on the pins.

Looking mighty fine! On your first post, pic number 6, what is the wooden cross shaped tool in the middle? 

  • Author
  • Popular Post
On 3/8/2025 at 7:38 PM, Coop said:

Looking mighty fine! On your first post, pic number 6, what is the wooden cross shaped tool in the middle? 

TC7.thumb.JPG.711c2611c6251c7c23601c4f50815011.JPG

As @gee-dub mention that's a reamer and the top right is a taper plane, both chair making tools. The tapers match so you ream the hole for the legs, arms, etc with the reamer and use the taper plane to taper the leg, arm post, etc to match.

  • Author
  • Popular Post

Ok time to cut the pins. I use Mike Pekovich's blue tape trick, it really helps with my bad eyes. First up apply the blue tape to the end of the top and bottom panel ends.

TC28.thumb.JPG.d5c447bb764818a63964c0bfad441275.JPG

Next and the most important task is to align everything. I use a light underneath (thanks @gee-dub the light you told me about for the spray room works great here as well) I also use a square to line up the edge

TC29.thumb.JPG.818b2e8cea10508a1fde2a1fd8fac80d.JPG

Shot showing square

TC30.thumb.JPG.28fc659783b0e68629757f1a6039098d.JPG

Here you can see the light just barely (I actually want it a bit tighter but took this so you could get the jest)

TC31.thumb.JPG.e2b6c20cab5ba8ee82505233530d11ba.JPG

Then using a marking knife mark each pin, sorry missed getting a pic of that. With that done I moved the board to the moxon vise to cut the joint. Just align the saw to the edge of the tape and cut, the straighter the better.

TC32.thumb.JPG.c67ae09d23e06224c7dd187ae7fb3a26.JPG

Now to clean them up I cutout most of the waste at the bandsaw

TC33.thumb.JPG.755b04888601c73fbf8906204fa83f13.JPG

TC34.thumb.JPG.775dd7cbbc9e4d1a1eeb11e7128d4ab8.JPG

Then head back to the bench and using a jig I made for holding the panels I get every thing squared up and flush.

TC35.thumb.JPG.649b46a59ab42efcf066f3864b83c3b5.JPG

TC36.thumb.JPG.6c364f73eaadb66f7767e21b39ca5b94.JPG

Then using a router and a spiral bit set to the baseline (very important to have the panel and bit adjusted to cut right at the baseline) I router out the waste

TC37.thumb.JPG.960ed757353ae00d63a0e710d2c5b2c5.JPG

TC38.thumb.JPG.adc530d6f5acc687b2f13cfa6fd0b563.JPG

All that's left is to clean up the wings with a knife and sharp chisel

TC39.thumb.JPG.6ba151154e639e4a79774386d3a5593b.JPG

TC40.thumb.JPG.80715a75b94dbde85da16c0902d87c71.JPG

TC41.thumb.JPG.4cce2544ec0d94e9321ff0e769c6541f.JPG

TC42.thumb.JPG.8b28ed73f1db88416d692cca37fc63a8.JPG

And with that we're ready to fit the top and bottom panels to the doors. First task use a pencil to put a little lead on the inside outer edge of the tails, this will let me know where I need to trim.

TC44.thumb.JPG.83c849faf38f41ad8babcf3bd0dd0f07.JPG

You can see the lead transfer in this pic

TC46.thumb.JPG.c9d5ead7b05812823089732a70378b62.JPG

Getting closer

TC47.thumb.JPG.84c266f514cce09960ebcc3a953b211c.JPG

Not perfect but not bad either

TC48.thumb.JPG.62d72f7b61a5e7a7e86029af2bddbcdc.JPG

TC49.thumb.JPG.e8c22e3b6396a83ab6d4bfaa7ebf1ea5.JPG

By using the TS to cut the tails and the router to cut the baseline you make getting nice looking DT's much much simpler, especially in hardwoods. With that the main box is coming together. I should note the DT's will be about a 1/32" proud by design.

TC50.thumb.JPG.6bb86233019ed7d4a579c065120c06c9.JPG

TC51.thumb.JPG.b6d0b9fe535a41d48a6ac316a0cddfbd.JPG

Next up is to cut the shelf through tenons.

 

 

I've used the blue tape, but never the router for the square & flat bottoms. I've always chopped them out, hence why I don't do many dovetails. I'll have to give it a shot.

  • Author
  • Popular Post

Time to cut the shelf tenons. First up some layout, I mark up from the bottom of the sides and mark the shelf location.

TC52.thumb.JPG.feb107cb87c46635165b6ef8b5e14fbe.JPG

Then using the same marking gauge setup from the DT's I mark the shelf all the way around on both ends

TC53.thumb.JPG.686d498d2ba5c92bcde09d71bae3356c.JPG

TC54.thumb.JPG.cacd871fff90924e1854f48b1284fc8e.JPG

With that complete I layout the three tenons marking the waste side

TC55.thumb.JPG.848486b77414854d734e7b65eedff2ae.JPG

After 5 min spent adjusting my blade insert to be flush with the TS table I cut a test cut using what I thought was a flat bottom blade ;) Ok quick blade change, now we have an actual flat bottom blade in the saw, and finally after a minor adjustment I am good to cut the tenons.

TC56.thumb.JPG.3a6e14d19ed9fc1d587f38469ff6d7e7.JPG

Using a sled tenons are cut

TC57.thumb.JPG.91145778f3489e239261dec1dda8d938.JPG

Then using a rip fence I cut a shallow shoulder on each face (more on why later)

TC58.thumb.JPG.75a1dc39fe7397bc5c037ee2c949dbcd.JPG

TC59.thumb.JPG.cd8c119f73f0108293975b7c8f9a5d94.JPG

Then at the BS I clean up the bulk of the waste

TC60.thumb.JPG.7f643f46d367a5fd0dac076c2a53ceb8.JPG

TC61.thumb.JPG.080701a499cdfef4426996ad755da968.JPG

Check layout one more time

TC62.thumb.JPG.0528f1c8484fd5b540112bfca9b435c0.JPG

Out of time for tonight but next up I will clean up the tenons with a chisel before marking and cutting the mortises in the case sides.

 

 

On 3/11/2025 at 6:17 PM, pkinneb said:

I cut a shallow shoulder on each face

I do the same thing for anything like this, even dados. I need all the help I can get making sure the shoulder is crisp.

  • Author
  • Popular Post

I started out by following Pekovich on the layout. First mark across the back of both sides, then marked a base line. Once that's done he used the shelf itself to mark the other three sides of the tenons by holding it on the side while using a marking knife to mark around the tenons. I found this to be extremely difficult and frustrating as I couldn't keep anything in position so I changed tactics on the other side.

TC63.thumb.JPG.93a5e309db1c5cc45774ba40f2c1db87.JPG

With the mortises marked I went to the drill press to hog out the waste.

TC64.thumb.JPG.aa0b54dd347736567f90dd91e136e38c.JPG

With the majority of the waste drilled out I grabbed a chisel and started cleaning them up 

TC65.thumb.JPG.82bee521235aad9b2554643d969b66cb.JPG

It didn't take long before I grabbed a mortise chisel, in this ash, it worked much better

TC66.thumb.JPG.0302d12f825d3e8e3b9123940645539a.JPG

Almost....

TC67.thumb.JPG.960181615671e34bb8071a5c68a51d04.JPG

Not terrible but not great either

TC68.thumb.JPG.75fe1726f07eb628cd21dd1077d7587b.JPG

At this point I decided I needed to mark the mortises differently and so with this side I set a combination square to the line and then cut them on each side before moving on. This worked much better. While the result was a minor improvement the frustration was much much less and I consider that a big win

TC69.thumb.JPG.dd2cb46bb7d87237d9dd2d03c82c5583.JPG

TC70.thumb.JPG.3961af21aecb998475f0d7ec61311eb1.JPG

With the done I need to cut out the back of each side to receive the 1/2" BB back panel, cut the mortises for the hinges, and the case will be ready for glue up. Hope to get more done tomorrow but we'll see with tax deadlines quickly approaching pretty busy in my business.

 

Looks great, Paul. I would have just run a few screws in from the sides.:lol:

You're out of my league, too.

15 hours ago, pkinneb said:

pretty busy in my business.

I thought you'd retired?  

  • Author
On 3/16/2025 at 8:39 AM, Mark J said:

I thought you'd retired?  

No I am winding down but still put in about 60 hrs a week between the two positions. Getting closer probably a couple more years but we shall see.

  • Author
  • Popular Post

First up today was to put a groove in the back of both sides for the back panel. I cut these at the table saw with a rip blade, one cut laying down and one on end. Here is my test piece. With that good I made the cuts on the sides.

TC71.thumb.JPG.025e0fe7ecd5b791c1aeab4d8d2c3c94.JPG

Then cleaned them up quick with a hand plan

TC72.thumb.JPG.3cdbcc5620126116508fcf6dbb4d4563.JPG

Next it was time to cut the mortises for the door hinges

I started by cutting a spacer the width of the hinge minus the TS blade

TC73.thumb.JPG.592c930f137c9aa73a39d471b0ecee17.JPG

Then it was time to set up the sled and do a test cut. I clamped a stop block to the right of the blade about 6" then put the spacer and a test piece in with another stop block to the left. The I removed the spacer, cut through on both ends, and finally slowly slid the board back and forth across the blade to make the mortice.

TC74.thumb.JPG.b03e0165de042ccd1ec5d7d5d112ee52.JPG

TC75.thumb.JPG.90e19afc0fa18e7783381dab4e7d4016.JPG

That'll work

TC76.thumb.JPG.42812b7c741c7720fee68b602b4a5a68.JPG

TC77.thumb.JPG.d23b60f6ec856b89e0bf9ae5ae3e566e.JPG

Now I set up the sled with a long fence and started cutting the sides of the case and the doors. I held the side in place with a quick clamp while I clamped the second stop block in place.

TC78.thumb.JPG.2039d717b68e7126565f3322875239fc.JPG

I used a piece of blue tape on the spacer to dial in the fit

TC79.thumb.JPG.77c9410b9c9f405abdcc54c9d0ada8ab.JPG

That'll work

TC80.thumb.JPG.54c06c58fb3a7e0ed20732582173d7a2.JPG

Here is what it looks like with both pieces

TC81.thumb.JPG.c6f105c4bc0d084cb179de70f60553b6.JPG

While this process works well it makes a heck of a mess of fine dust that even decent DC doesn't really help with

TC82.thumb.JPG.7007ad4698bec92d2d69e396926865ae.JPG

Next up I need to clean up the panels.

TC83.thumb.JPG.357f0f94d0133f7a06a02b7a32f0c4c2.JPG

First I planed the edges

TC84.thumb.JPG.36d2e0ee3c5095c42d3e84c7aa1f33df.JPG

TC85.thumb.JPG.0f86e69cc6eb855f52eb1175545eafd0.JPG

TC86.thumb.JPG.0012a385b64ce603f676243c20e16ead.JPG

Then it was time to tackle some dents I had caused using the side of a rubber mallet to take parts apart while cutting the dovetails not realizing I was marring the sh$% out of the panels.

TC87.thumb.JPG.eabffeb61ff891aeee9e09ce725e46c0.JPG

Time for a little steam and a damp towel

TC88.thumb.JPG.733d4108af7843b95f8ce1d7955db0df.JPG

TC89.thumb.JPG.12464e006933fcaf596f5915e62981d2.JPG

TC90.thumb.JPG.c168d2e43fa18bcb8454a485462f97cb.JPG

I also head a couple dings on the ends and while I knew I probably couldn't totally repair them wanted to try and make them better at least.

TC91.thumb.JPG.3faba2c94658055420c95bc0dd90f103.JPG

Not perfect but definitely better

TC92.thumb.JPG.984991e63694118bdd98f9f4e9a5cef1.JPG

...and another, two on the edges and two down further and in a bit (the handheld lamp I bought for finishing a couple weeks back came in handy here as well.)

TC93.thumb.JPG.36dc1b765b22fdf283a1033541969a88.JPG

Much better

TC94.thumb.JPG.68cb5dfac88bf84d135cdaf56346a153.JPG

Then sanded the sides 

TC95.thumb.JPG.181592a5cbc3af0c4a1658b85821cdc3.JPG

TC96.thumb.JPG.309c335f516ae402a36a658b02c6abec.JPG

I used a plane to break the edge of the front of the shelf as I won't be able to get to it after glue up

TC97.thumb.JPG.9203f67eceded4c774954a4b36f76b6d.JPG

One tip always mark your parts, in a placed that won't be seen, to keep things straight at glue up

TC99.thumb.JPG.2d40801135d7b48539142878d0d7c20b.JPG

Ran out of time but still need to clean up the ends and add small chamfers in a few spots

 TC98.thumb.JPG.887a8eca244c00cabb98491f234c4bc2.JPG

Once that's done the case parts will be ready for a quick coat of shellac before glue up.

 

  • Author
  • Popular Post

Finally got back out to the shop tonight for an hour. Was able to get the ends cleaned up and chamferd.

Started with the pins by adding a small chamfer all the way around, then I could plane the ends without worrying about tear out

TC101.thumb.JPG.15ca748617fab2e949abef49b1d172d2.JPG

A plane makes quick work of the TS blade burn marks on the end grain 

TC102.thumb.JPG.47352ee821ae99468c09be97bb19f411.JPG

TC103.thumb.JPG.f5581da620b588e8d623c120e13563f6.JPG

I use a shoulder plane to get between the tails

TC104.thumb.JPG.a46c3c78172ae124ce6a82dd71dabee8.JPG

Then use a small handplane for the outside edges and the ends

TC105.thumb.JPG.eb977b70c439d95b26402547d887fe3d.JPG

TC106.thumb.JPG.1ceb8b2e1d46318562af99ff943e3202.JPG

I finish with a quick hit of 220 using a stick to insure I don't round anything over inadvertently.  Yes I did get a new piece of sandpaper :)

TC107.thumb.JPG.6ca5447cacd781f193d1a93d2698ec52.JPG

TC108.thumb.JPG.a3c24ea8215c5e8c0da5ea469e862dc5.JPG

You can see in this pic they only stick out a little over a 1/32" so you have to be careful you don't go to far

TC109.thumb.JPG.6d42e0f787e5a047567af9c523a524f0.JPG

final test fit

TC110.thumb.JPG.f2b38a6ea6f4b7ad88dcc3ebc206f29a.JPG

Here you can see a better shot of the DT detail

TC111.thumb.JPG.c38a8705a4e8326c0f529ef540ede6c6.JPG

Tomorrow I will cut the back panel so that's ready to go and then add a coat of shellac. I hope to get the case glued up first thing Saturday morning as I don't do glue ups after working all day.

 

 

 

  • Author
  • Popular Post

First up today was to size the back. Using a scrap of BB I determined what I would need. 

TC112.thumb.JPG.92800b65531d4b07a0241f9d83a57774.JPG

Then I pulled out the 2" foam and track saw to make the cuts

TC113.thumb.JPG.f27c711b7f4bfde1e4303ec2a701b25e.JPG

Since I had that out I decided to layout, and cut, the frame material for the frame and panel door faces. I made a quick pattern (for the sides) I used to determine where to get the parts from.

TC114.thumb.JPG.7c192ac6652a3ad49003073dedb3c299.JPG

I ran into an issue as a couple boards I planned on using had way to tight of grain compared to the rest of the cabinet which would not have looked good.

TC116.thumb.JPG.04826bdb893b5047a34f6948eb9bfae1.JPG

So I moved on to another couple boards and was able to get what I needed. Following the grain not the edge of the boards

TC115.thumb.JPG.2560720aa4f0409ac7516bba42bd6d63.JPG

TC117.thumb.JPG.9f94f2971c0868343a77daee98a71f52.JPG

Then using the track and jigsaw I cut them to rough size

\TC118.thumb.JPG.1705246c4ac3cb8da79ed11367fac395.JPG

Then I ran them through the jointer and planer to flatten them on both sides

TC119.thumb.JPG.201cbef63cbc9a56a309fafa68ba80f9.JPG

With  that done, I drew the line I wanted, cut them on the BS. jointed that edge, and finally cut to length and width at the TS

TC120.thumb.JPG.389dcd128d0c7085d2050254b8ec9ecc.JPG

I did end up with a piece I couldn't use (top) luckily I had a spare

TC121.thumb.JPG.dfd0cffe546b1eda488827d963ae1351.JPG

This is when a digital gauge comes in handy. Just zero it out to the final dimension and l run it through until you get to 0

TC122.thumb.JPG.eec3ee306b9063b4c406be60c71bb15e.JPG

That'll work

TC123.thumb.JPG.26f7239f98f3fafeed420c5143774dee.JPG

I plan on using veneered BB for the panels and started looking at boards for the veneer. This might work if I add a little extra white strip from the board on the left to each side to get the dimension I need. 

TC127.thumb.JPG.31259e3ddacccc0b1334e850c28781aa.JPG

I also received a step stool I ordered. The cabinet will be above my grinders and to reach the very top I will need something.

TC124.thumb.JPG.8dfb63d3c10858e27477aceb2cc9acf3.JPG

TC125.thumb.JPG.7b779b12db63cb79b2f2de55f04da497.JPG

TC126.thumb.JPG.57051b5583476669ff3c15d900ffd293.JPG

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.