Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Table saw placement - against a wall or in the middle of the shop?

Featured Replies

I'd prefer to put the saw in the middle if I have the space.  My table saw has 52" rails and my shop is narrow, so I have the saw in the middle of my shop with the ends of the rails against the wall. 

 

If space is tight, use a mobile base so you can reposition it for longer or wider cuts as needed.

I think it depends on what you normally make/cut.  If you need the extra space to the right of the blade, as Chip does, then in the middle makes sense.  But if you consistently cut smaller pieces, and shop space is at a premium, then against a wall can work.  With a full 2-stall garage, I'd shoot for putting it in the middle with an outfeed table.

 

Either way, I would mount it on a mobile base.

Mine's against the wall but on a mobile base so I can pull it out into the shop if I want. Most of the work I do is ok with it against the wall. Any large rips of 8x4 sheets and I can pull it out. When cross cutting long items on a sled if they touch the wall before lining up the cut line - roll it out again.

The mobile base wheels axis are set at right angles to the axis of the blade.

Middle as well.  I use all 4 sides of my saw tho.  In feed, out feed, built in router table, and a walk way. 

 

I have a fairly small shop so, this actually turned out to be a better use of space since that's one of my primary tools.

In an open spot with jointer at the right end going the other way.  That way as pieces come off the jointer ready to be sized on the table saw, they can be placed right at hand on the right side of the fence.  A step on the other side of the jointer is a radial saw or miter saw, so when selecting out parts of boards to length, they can go right from rough length to jointer to table saw.  Steps add up on projects with many pieces.

 

If walking around in circles is a normal part of the thought process, it doesn't matter

Def not against a wall if possible. As soon as you move the saw there, you will need to cut a long board.

Mine is close to the centre of my space, and the out feed table doubles as an assembly table or place to put number during milling.

In my old, very small shop, my saw was against a wall, and I hated it. It's on a mobile base, but I still don't find the mobile base very mobile. It always needs adjustment before and after moving (herculift that came with the saw).

mine up against a wall , with wheels , but be careful wheels are good mine makes black marks on pavement if too much sawdust slows down wheels.

Count one more for the for the middle...

 

The rip capacity need is obvious, but crosscut capacity on both sides of the blade can be important.   Don't overlook things like opening doors and windows when considering rip capacity.   10 feet of rip capacity and 5 feet of crosscut (both sides) can cover most work if you're not making millwork.  If you do floor to ceiling case sides, 5' will let you dado 10' sides when flipped end to end.

 

If you're making furniture only, no built-ins, you can get away with less, but remember the blade only tilts one way and you want to cut with the good face up.

 

When you look at space, don't forget space for the operator to move around the work, and remember that the saw can be turned for odd jobs to avoid obstacles.  Table saw / outfeed setups can also make great assembly areas, with a sheet of melamine on top, or spray tables, covered in cloth.

My shop is only 15 feet wide, so the saw is in the middle when I'm using it, and rolled against the wall when I'm not. If I had the space, I'd keep it in the middle.

I say the middle. My saw has wheels, so it is easy to move around when it is in the way. I also use it as a stand for my powered planer, which isn't ideal, but it's what I have right now :)

In the middle nearer to the door so it is close to unload and rip stock and sheet goods. I made a 5' x 12' out feed table that doubles as an assembly table for large projects. Ripped sheets can be staged for cross cut on the other saw. Both saws are in the middle of the shop so everything circulates around them.

I have mine so you can access all sides of it but thats because of the mobile base I built for it so I could get maximum storage otherwise put the right side to the wall. The other reason is it allows me to rip boards longer than 10' just by opening the door to the shop on the in feed side and I have about 15' on the out feed side.

 

Every cabinet shop I have ever worked in the right side of the saw was against a wall or a storage rack but we also had 52" rip capacity to the right of the blade. We never had a need to cross cut longer than that ever and that's over 30 some odd years of working like that.

Tablesaw is at the far end, behind the 12 ft heart pine table being assembled.post-6363-0-50769500-1377224607_thumb.jp

The Excalibur sliding crosscut table is attached to my other UniSaw , 5 x 8 out feed table is under 38 drawers for one kitchen.

post-6363-0-12161200-1377224805_thumb.jp

We cover the tables with 1/4" MDF when we stain and finish. So the whole shop revolves around the table saw and out feed tables.

outside of this forum, I've only seen one example where a table saw was against a wall, and they had it placed so the offcut side was closest to the wall.  (And the offcut side was capable of offcuts about twenty inches, max.)  Almost everybody i've seen has either "permanently" placed the saw in the center, or mounted on a mobile base to pull it into the center when needed, and store it wherever (usually against a wall).

 

If you have the space, use it.  You will appreciate it.  If you don't have the space... move.   (Sorry, late night humor.)  Move the saw is more appropriate. 

I actually have the left side of the table saw closer (about 2' from it) to a wall.  It does present some challenges when cutting long stock, but usually find a way around it.  The decision was based more on the flow of the shop then anything else, and overall has worked well.  However, I would not be surprised if at some point I changed that, as shop layouts tend to be always changing.

I had the brilliant idea to put my saw against the wall one time. It drove me nuts, not being able to walk around it on the right side. I felt like I was constantly having to go "clean around the barn to get to the woodshed."

  • 2 weeks later...

Def not against a wall if possible. As soon as you move the saw there, you will need to cut a long board.

Mine is close to the centre of my space, and the out feed table doubles as an assembly table or place to put number during milling.

In my old, very small shop, my saw was against a wall, and I hated it. It's on a mobile base, but I still don't find the mobile base very mobile. It always needs adjustment before and after moving (herculift that came with the saw).

Sounds like we have the same setup. Of course, I always get the assembly area cluttered and then need to rip a long board...

My shop is 12.5 feet wide and the TS is permanently set up near the wall.  It's on wheels but I've never needed to move it for a cut.  I used to have it in the middle with narrow passage on either side but much prefer having it against the wall.  I have fit so much more stuff in the shop with it there.  The best thing is your power and dust collection isn't a problem.  I have the jointer on the left side of the TS essentially in the middle of the shop and the miter saw on the wall to the right of the TS.

Size and shape of shop certainly has a direct effect on where the tools live.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.