duckkisser Posted September 20, 2013 Report Posted September 20, 2013 I have started geting ready for the winter. i will be turning all my bowl blanks in the driveway while its nice. then during the winter i will inlay pictures in the bottoms of my bowls when its cold. those usualy will take 2-6 days depending on the complexity of the colors. how do you guys prepair for the colder months? do you do anything special? Quote
Freddie Posted September 20, 2013 Report Posted September 20, 2013 I am going to be finishing up my garage now so i will not have to deal with a freezing emvironment like last year. Quote
..Kev Posted September 20, 2013 Report Posted September 20, 2013 I have a pellet stove in my shop so, I just turn up the heat a little and keep working. I do store up on lumber a bit to save me long trips in bad weather to get it but, that's about it. 1 Quote
bobcrosley Posted September 20, 2013 Report Posted September 20, 2013 My winter prep consists of getting ready to do some woodworking. No AC in the garage means that my hours in the summer months are limited to basically what I can stand to do, and how much sweat I want to clean off my tools and work pieces. Quote
Indy Cindy Posted September 20, 2013 Report Posted September 20, 2013 I will be working indoors on carving and surface treatment of my turned pieces. I would like to add heat to my garage shop this year so I can continue to turn. What do people recommend for a garage that doesn't have an electrical draw yet is safe? Upgrading power out there needs to be done, but isn't in the cards right now. I tried electric space heaters last year, but they didn't make a dent in the cold and I had to turn them off to run the shop vac. FYI, I am in half of a two car garage, the other half houses my husband's car and motorcycle. Quote
Rapid Roger Posted September 20, 2013 Report Posted September 20, 2013 I wrap the window AC with plastic to stop the wind, remove the window tint off of the windows to let in more light and heat from the sun and carry the electric heater up from the basement. Then start looking and planning for smaller projects to do for Christmas gifts. Rog Quote
Indy Cindy Posted September 20, 2013 Report Posted September 20, 2013 For whatever area I carve out of the garge for winter work, I am going to put up a zip wall to close it off from the rest of the garage. There is no way a small space heater can keep up with overhead doors opening and closing or a large unconditioned space. I am hoping that I can run a space heater for a few hours and get it up to at least the 50 degrees. At that point I can work comfortably. I tried something sort of like that. I set up an ez up tent in my garage and hung blankets from it. I used a couple space heaters and it did not noticeably warm up even that small space. The only advantage of the setup is that it is really good to hang my fluorescent lights on and by hanging a tarp on one side I can contain shavings from woodturning to that section of the garage. So I still have it set up without blankets and I like it. For the really hot humid summer days I installed a window air conditioner which is extremely effective taking out the humidity and dropping the temp down a bit. I direct the cold air into my setup with a regular fan and I am very comfortable. I just have to let my husband know when I have the a/c on so he doesn't pull his car in and undo it all. Quote
G S Haydon Posted September 20, 2013 Report Posted September 20, 2013 I have a pellet stove in my shop so, I just turn up the heat a little and keep working. I do store up on lumber a bit to save me long trips in bad weather to get it but, that's about it. Snap, come spring the lumber is nearly all gone, works like a dream. Quote
ChetlovesMer Posted September 20, 2013 Report Posted September 20, 2013 I normally bring my glue and other stuff that might freeze in for the winter then cart them out with me to the shop each time. My shop is well heated but if I'm not going to be in there for a while I shut the heat off and the temp can drop below freezing. Frozen glue isn't as good as frozen yogurt. I'm thinking of building a warming case that would keep those things above freezing during my "shut down" times. But I've been thinking of building that for like 7 or 8 years now. Quote
duckkisser Posted September 20, 2013 Author Report Posted September 20, 2013 don't need anything special just get a small box put a low wat bulb in there and you are good to go. Quote
rodger. Posted September 20, 2013 Report Posted September 20, 2013 I pretty much shut down the power tool shop as well, at least for 4 months or so. The fall is nice to work in, up to November or so. When it gets really cold here on Ontario, I clean all my tools with wd40, seal with topcote, and then some paste wax. Then some old towels or blankets go over the machines. All my hand tools go to the basement shop, or hand tool shop. Then I'll do some hand tool only projects to keep me busy over the winter. I do have a heater, and my garage is insulated, so I do some power tool woodworking from time to time over the winter. Quote
Duncanw Posted September 21, 2013 Report Posted September 21, 2013 I had my garage wired with a 220 outlet and plug in an industrial heater. Works like a charm. If I put it on full I can get it up into the 70's in the cold winter Quote
ChetlovesMer Posted September 22, 2013 Report Posted September 22, 2013 don't need anything special just get a small box put a low wat bulb in there and you are good to go. Duck, You are 100% correct. But I'd like to add a thermostat to turn the bulb off when its warm enough inside the box... ooooh, then I'd like to add some Styrofoam insulation to the box to make it more efficient.... ooooh, then I'd like to have a snazzy door on the bock with a latch.... oooooh, then I'd like the box to hang on the shop wall and look nice.... Darn it, I just turned this into a project.... Okay, put it on the list. Quote
duckkisser Posted September 22, 2013 Author Report Posted September 22, 2013 last winter I put my glue in a wood milk crate set a desk lamp inside it pluged in a Christmas tree timer and forgot about it for about two months strait. Quote
wdwerker Posted September 22, 2013 Report Posted September 22, 2013 We put the fans up and use a few halogen lamps to compensate for the lack of natural light with the roll up door closed most of the time. The extra heat from the halogen lights is welcome but it's only for about 3 months at the most. Quote
ChetlovesMer Posted September 22, 2013 Report Posted September 22, 2013 last winter I put my glue in a wood milk crate set a desk lamp inside it pluged in a Christmas tree timer and forgot about it for about two months strait. Very clever. Quote
duckkisser Posted September 22, 2013 Author Report Posted September 22, 2013 Very clever. not realy just sometimes its over kill to go over board when we make stuff. its like making a work bench out of purple heart, rose wood, zebra wood ect..... when a 2x4s and some cheap ply will do the same job. rather mess up some cheap ply then use the lumber that cost more then my truck. 1 Quote
Ozwald Posted October 7, 2013 Report Posted October 7, 2013 Business as usual. Winter's already here. Luckily my shop is in the basement of my 100 year old house. It hasn't gotten all that cold yet - upper 20's - but it stays pretty warm down there. It also helps that I have a boiler instead of a furnace & hot water heater. They don't build 'em like they used to. Quote
duckkisser Posted October 7, 2013 Author Report Posted October 7, 2013 do you even have decent electricity down there? Quote
Ozwald Posted October 8, 2013 Report Posted October 8, 2013 do you even have decent electricity down there? It's not the Grade A stuff, but I'm pretty sure it's USDA approved. Quote
ColinF Posted October 30, 2013 Report Posted October 30, 2013 not realy just sometimes its over kill to go over board when we make stuff. its like making a work bench out of purple heart, rose wood, zebra wood ect..... when a 2x4s and some cheap ply will do the same job. rather mess up some cheap ply then use the lumber that cost more then my truck.Duck, my father would have liked you. Of course, I grew up thinking exotic wood was select grade pine, but he made and sold a lot of stuff made out of pine. I made him a bench out of 2x4's that's pretty strong. I'd like to remake it out of hard maple but considering it costs the same as walnut at my supplier, I think I'll stick with 2x4's! I don't do much for winter, I have a large kerosene heater, but my barn isn't insulated so it's pretty cold up there in the winter, one day when I build my pole barn I'm putting in a fireplace and pellet stove! No more frozen glue Quote
CessnaPilotBarry Posted October 31, 2013 Report Posted October 31, 2013 how do you guys prepair for the colder months? do you do anything special? I switch on the heat. 1 Quote
JoshC1501 Posted November 6, 2013 Report Posted November 6, 2013 I have one of these common Garage Heaters for my shop. http://www.modinehvac.com/web/Hot-Dawg.htm#.UnooPZSTJOh I had it at my old shop and moved it to the new house last fall. Didn't get it installed last year though. I am waiting for the HVAC guy to come an install, should be in the next couple of weeks. It is very efficient and heated my old shop from 50 degrees to 70 in about 10 minutes. I usually keep the heat down to around 50 when I am not working out there, so I don't waste natural gas, then crank it up for the weekend or when I am planning to work out there. Josh Quote
Spencer_J Posted November 8, 2013 Report Posted November 8, 2013 I start drooling over the filson winter catalog around november 1. I have a detached garage with no insulation so i block the windows and gable fan with perfect fit rigid foam pieces. Glue, paint, finishes go in the basement of the house. Clean the gutters. Put blankets in the cars. Shut off the sprinkler system. Then i start looking at warm places to send my girl to for jan and feb. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.