TerryMcK Posted December 29, 2013 Report Posted December 29, 2013 This is what I was surreptitiously making for my wife Elly's Christmas Present while locked (literally) in my shop. American black walnut is the primary wood and French oak is the secondary. All brass hardware is Brusso or made by me. The drawers are lined with self-adhesive green felt. The jewellery box is loosely based upon Norm Abram's original on New Yankee Workshop but heavily modified by me. The inlay EMH are my wife's initials and I made them from mother of pearl. Then I inlayed them into the false top drawer front securing with some CA glue. Do you know how difficult it is to make something surreptitiously and keep it hidden from the intended recipient? It's very hard. I've had a few close calls before Christmas with Elly coming into the shop when you least expect it. I do have a warning buzzer on the door and I can lock it from the inside. She came into the shop on numerous occasions during this build and had been stood very close to the casework. I had it hidden under a black plastic dustbin liner (a garbage bag for my North American friends) with all manner of detritus scattered all around. She did suspect something was going on though occasionally asking "what you making?". I had to reply "I'm doing some practice dovetails to hone my skills" - big fib! Anyway I finished everything at 4PM on Christmas Eve just in time for Santa to load it onto his sleigh. Finish is 4 coats of GF Enduro-Var satin over shellac using HVLP. Here's some pictures and the full build is documented at my blog. Closed up box Partially opened box Shhhh! The hidden drawer. Don't tell anybody Jewellery box fully opened - all the drawers are lined with felt. 1 Quote
..Kev Posted December 29, 2013 Report Posted December 29, 2013 Love that bottom drawer! Awesome workmanship! 1 Quote
Trip Posted December 29, 2013 Report Posted December 29, 2013 ==> This is what I was surreptitiously making for my wife Elly's Christmas Present while locked (literally) in my shop I'm not building one of these anytime soon... If you remember your High School Physics, jewelry obeys the Ideal Gas Law -- it expands to fill its container... Nice job... 1 Quote
Eric. Posted December 29, 2013 Report Posted December 29, 2013 Beautiful work, Terry! Love that MOP inlay. Looks great. I don't have to be sneaky in my shop. My wife cares not. It all looks like detritus to her. Until something is finished and I bring it into the house, she pays zero attention. 1 Quote
Trip Posted December 29, 2013 Report Posted December 29, 2013 Follow-up question, how many hours on this... Bottom drawer is clever, how'd you support the front of the cabinet and still let it slide? Quote
Pwalter5110 Posted December 29, 2013 Report Posted December 29, 2013 I really love that hidden drawer. Amazing. Quote
..Kev Posted December 29, 2013 Report Posted December 29, 2013 Follow-up question, how many hours on this... Bottom drawer is clever, how'd you support the front of the cabinet and still let it slide? Look at the 3rd pic for the answer.. Quote
TerryMcK Posted December 29, 2013 Author Report Posted December 29, 2013 I guess it was about 20 hours over a 4 week period a combination of some machine work and lots of hand tooling (hybrid woodworking!) . I didn't get much time to work on it constantly due to the day job and you lose track of time in the shop. The two sides of the lower sliding trim pieces have dados cut into them. The internal hidden drawer also has dados cut into both sides. They both run on a common track 1/4" thick that protrudes 1/8" internally and externally. You can see the track on the third picture in the sequence above just in front of the rear leg. The internal hidden drawer is then glued to the front trim so making up one assembly. The bottom of the trim assembly is about 1/32" off the "ground" level. The carcase sides have hidden legs that sit on the ground so the hidden drawer can slide without hindrance. There is a stop bar hidden underneath that prevents the whole drawer from being pulled out and this also keeps part of the dados in contact with the track stopping it from tilting. The stop bar is fixed in position using screws and brass brackets I made. Here are some pics. Blue tape is covering the dados but you can see the imprint. Quote
TerryMcK Posted December 29, 2013 Author Report Posted December 29, 2013 And another pic here. What you see on the outside is also on the inside supporting the internal drawer. The drawer and the external trim are glued together so they always keep perfect alignment relative to each other once they have been positioned on the track. Quote
Trip Posted December 29, 2013 Report Posted December 29, 2013 ==> Here are some pics. Blue tape is covering the dados but you can see the imprint that makes it clear. thanks. 1 Quote
G S Haydon Posted December 30, 2013 Report Posted December 30, 2013 Very very nice Terry! She must be delighted with it. Really nice to have good photos to drool over too. 1 Quote
Byrdie Posted December 30, 2013 Report Posted December 30, 2013 Really sweet, well thought out and very nice looking. 1 Quote
Coop Posted December 30, 2013 Report Posted December 30, 2013 Great looking design and construction. Really like the hidden drawer. Also, I've got to remember the phrase "plastic dustbin liner"!! HA! 1 Quote
woodieboy Posted January 3, 2014 Report Posted January 3, 2014 You did an outstanding job there! I really like the design and the details are a top notch! 1 Quote
Egraff Posted January 3, 2014 Report Posted January 3, 2014 That's really cool. Such a clever idea for the bottom drawer. I really like it. 1 Quote
lildesertwoodshop Posted January 4, 2014 Report Posted January 4, 2014 Terry super nice !!! Hidden Drawer is great ! well executed ! 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.