Recommended Posts

Posted

Just finished this floating top hall table. 14" deep, 49" long, and 31" tall.

 

I ebonized some oak using Speedball India Ink. It was a very interesting process. I did three coats, with a wipe of #0000 steel wool between coats. In the end the ink seemed like a thin coat of black paint - and it is BLACK! 

 

I finished the entire piece with a hard wax oil, two coats also with a #0000 steel wool wipe down between coats. I don't think the wax oil penetrated the ink, but it gave it a nice sheen when polished.

 

The black walnut is from a local sawyer.

post-15223-0-98679400-1433180857_thumb.j

post-15223-0-15030800-1433180861_thumb.j

post-15223-0-55250000-1433180864_thumb.j

post-15223-0-11140000-1433180882_thumb.j

post-15223-0-71641000-1433180899_thumb.j

  • Like 2
Posted

Awsome piece!!! I love floating tops! Is there a side apron? I can't tell if there is one that is inset under the top. If there are no side aprons what keeps it from racking?

there are three - one in the middle, and two out near the ends. they are set in a bit, where the through tenons are. the top sits on them. having them sit in so far make it look there are not sides.

Posted

Wow - nice Job. Can you elaborate more on then colouring process? I really like the dark colour.

there's not really much more to say. i used a foam brush to apply the ink, and did three coats. it dries really fast,so was able to put the next coat on after 30 minutes. it was very simple, not even I could screw it up. i tested a wipe-on poly to see how it would look over the top of the ink, and to see if it made the ink run - I didn't want to mess up the contrast at the dovetails. it worked fine, no smudging. I went with the hard wax oil, because I like non-toxic finish and the more natural look and feel.

  • Like 1
Posted

Yes it is. I cut the ends first on my sliding miter saw, then cut the long one on the table saw. Used a hand plane, scraper and sand paper to clean them up.

I think I will make mine where the long sides are not parallel, wider in the middle. There has to be a name for it, oblique comes to mind but doesn't sound right. Anyway, I guess I'll use a chamfer bit w/ bearing.

You did good!

Posted

Aelwesome job Shane! The almost gun-blue black makes for a very interesting and unique look. I'm going to steal that idea soon!

it may look gun-blue black on your screen, but let me assure you it's JET BLACK - like black, and only black. like looking into the eyes of a demon.

Posted

I think I will make mine where the long sides are not parallel, wider in the middle. There has to be a name for it, oblique comes to mind but doesn't sound right. Anyway, I guess I'll use a chamfer bit w/ bearing.

You did good!

would you do the just oblique the front out to a shallow point, or make it like a parallelogram?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 75 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined