Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Smoother, to camber or not camber

18 members have voted

  1. 1. Do you camber your smoother Blade?

    • Yes
      50%
      9
    • No
      44%
      8
    • Uhhh camber?
      5%
      1

Please sign in or register to vote in this poll.

Featured Replies

That is the question

 

I find I get some lines or tracks with the smoother. How many of you camber your smoother blades?

   Like Mr. Shaffer, just a touch, sometimes a corner will grab a curly or twisted grain, a slight camber allows a tiny bit of skew!

No. I only camber my #5 and that is only very slight The smoothers are set to take very light cuts of around 1 thou or so and don't leave any tracks at such light cuts.

I'm voting yes, although it is a categorized yes. I do not camber the blade to the extent you would a rough work blade.

I've made myself a little griller with this, I have a strip of blue tape about 5 thicknesses that goes under the outside of the roller for two or three back and forth passes. That done on each side does create an other than perfectly flat blade edge or camber but it's barely noticeable to the naked eye.

  • Author

I eased the corners with the camber roller on my MKII just now. Gave it a whirl. I'm getting full shavings and a very smooth surface. 

  • Popular Post

My drum sander didn't come with a blade

I tend to go old-school: camber the same amount as the thickness of shaving you plan to take....

 

I don't camber in an arc -- I have very little camber in the middle 2/3s of the iron (actually, I plan for it to be flat, but sharpening is what it is so there is always some curve, but think of it as flat), then a bit of camber at the edges... We're talking a couple thou on a smoother...

 

The short answer: on a dedicated smoother, we're talking a 2 thou camber at the margins, flat in the middle...

I camber my smoother, works great. Just put some extra pressure on one corner for 5 strokes, then again for the other corner. Then take 3 between the corner and center (left side) and then 3 strokes to the right of centre.

==>I find I get some lines or tracks with the smoother

You ask about cambering, but not about knocking-down the corners...

 

On most of my bench planes (maybe all planes that are not used to establish and/or refine joinery), I knock-down the corners – even if I don’t camber the irons... This largely mitigates ‘tracks’. In fact, I believe I started knocking-down the corners prior to cambering and it was rounding the corners that eliminated tracks in most operations...

 

 

Method: I flatten my waterstones (and dress my Tormek) with a diamond plate... Basically, 2-3 rounding strokes at the corners makes a nice even radius – it’s only a couple thou, but makes a big difference...

 

Chris Schwarz demonstrated the technique in several of his DVDs and I believe David Charlesworth does as well...

 

Before cambering your irons and deciding you don't like it -- try killing the corners and see if that helps...

I can't imagine a smoother without a camber, or any plane to be used on the face of a board that doesn't hang off each side of a piece.  Each of my smoothers has a different camber based on the thickness of shaving it takes, even the one that takes a little less than half a thou.  We do a lot of matching of old smoothing plane patterns in really old houses-the reason for more than one smoothing plane.  I've never seen old smoothing plane marks where only the corners were rounded.  If it's all going to be sanded after, why use a smoothing plane anyway?

 

After a small article sometime back in the '90s in FWW telling why smoothing planes needed cambered irons, I decided there was really no good reason why I should renew my subscription after being a charter subscriber and being anxious to get any issue from the start, but the excitement had turned the corner to dissappointment. 

If I smoothed more wide faces, I might camber. But, I end up smoothing lots of edges that I don't want dished even a little. I find the corner knocking to be an intermediate that allows for dual functionality. This might be a good case for multiple smoothers like you reference Tom. I don't see the need to copy old time marks in my world.

  • Author

==>I find I get some lines or tracks with the smoother

You ask about cambering, but not about knocking-down the corners...

 

More so about knocking down the corners to a slight radius or camber. I knocked my corners down 2-3 thou. Similar to rounding the corners on a skew chisel for a lathe. 

Yeah, Tom, I just ease the corners a bit. Honestly, I never finish right off of my smoother anyway. The old ROS takes care of my skid marks er, I mean plane tracks. :D

A card scraper can get rid of those tracks without scuffing up your nice freshly planed surface.

Yea, but if you mix scraping and planning on the same face, you might as well add a round of hand sanding to get a consistent surface for finishing -- it's the ugly little secret with card scrapers...

 

I finish every project with some hand sanding... In a typical project, some faces will be planed, some scraped, some RoS and some wide-belt... Almost every project is a mixed-bag of initial surface prep, so I just allocate some time with 180g to get all surface the same final prep...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.