Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

coffee table from reclaimed oak

Featured Replies

I built this coffee table completely out of reclaimed oak. The top of the table is built using 1.25" thick butcher block planks that came out of salvaged semi-trailers. I'm not sure of the age, but they were filthy when I bough them and have tons of character. The legs and apron came from beams out of an old barn.

One of the biggest challenges for me was striking the right balance between highlighting the "character" of the salvaged wood and showing craftsmanship in the final piece of furniture. I left the top rough and did not plug the holes, but I did plane the planks down to get them flat and to a consistent thickness. 

coffee table small.jpg

coffee table top small.jpg

Very cool Andy!  Goes well in that room!  Make sure you sign it!

  • Author

I bought the semitrailer wood from a guy in Oklahoma who had it stacked to the ceiling in his garage. 

  • Author

Thank you for the kind comments. When I took the pictures in our house I didn't have the best lighting and didn't get to show any of the details on the base of the table.  Here is a pic of the base taken while i was finishing the table in the shop.

 

The apron is mortise and tenon, with a bead detail. The legs are solid oak with a taper on the inside faces. I left the original saw marks on the wood wherever possible.

IMG_20150824_172939756_HDR.jpg

I Like the beed detail and I think 8 people could sit on it that table and it would still be fine..Very nice.

I just hope that the finish doesn't get scratched form use!  :)

 

Nice job buy the way.

 

Rog

Dumb question Andy, but as old and stable as this oak must be, why did you put the cleats underneath?  I'm getting ready to build a sofa table out of some old reclaimed material so the answer will be helpful n my build. Thanks!

It is still wood and as such it will continue to absorb/ dissipate moisture and thus move. Modern houses pose a reduced risk as the humidity in the air is less prone to change over the season. However, in my apparent (brick house, 120 years old, no AC) there is still quite a change in humidity. If anything: a clear is always good, safe practice

  • Author

Dumb question Andy, but as old and stable as this oak must be, why did you put the cleats underneath?  I'm getting ready to build a sofa table out of some old reclaimed material so the answer will be helpful n my build. Thanks!

 

The pieces for the top were not perfectly flat, but I didn't want to go crazy with removing wood to flatten them out because then I would end taking the imperfections out of the high spots in the table top. I also don't have a great way to flatten a board that is 12"x52" in my shop.

Since the pieces didn't line up perfectly for a glue up, I left the top as four separate wooden planks that are not glued together (top is 40" so they are each 11" inches wide with a 1/2" half lap on each end). The cleats hold the top together and they also hold the top flat (each plank was within 1/16" of an inch so I don't think it will pose any long term problems). I used slightly elongated screw holes to allow for some wood movement.

 

Cool...I was hoping the cleats were not glued....:)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.