Chet Posted January 7, 2016 Author Report Posted January 7, 2016 Well I figured it was going to end up being some other color eventually when I decide what kind of finish to use on it. Any thoughts? I don't want it to be all slippery, I think that would defeat some of its purpose. Quote
Al Capwn Posted January 7, 2016 Report Posted January 7, 2016 4 minutes ago, Chet K. said: Well I figured it was going to end up being some other color eventually when I decide what kind of finish to use on it. Any thoughts? I don't want it to be all slippery, I think that would defeat some of its purpose. Chris Schwarz says, "...Your benchtop should be as grippy as possible. As a result, I think that an oil finish such as linseed oil, might be the best workbench finish...However, an oil finish leaves little protection against water and spills. So I mix equal parts alkyd varnish, BLO and low-odor paint thinner..." I have heard others use BLO or spar urethane. 1 Quote
Popular Post ..Kev Posted January 7, 2016 Popular Post Report Posted January 7, 2016 If it were my bench, it would just be a bit of danish oil and done. Another personal choice tho. 5 Quote
estesbubba Posted January 7, 2016 Report Posted January 7, 2016 Another vote for Danish oil. It's cheap, quick and won't darken lighter woods as much as BLO. 2 Quote
Chet Posted January 7, 2016 Author Report Posted January 7, 2016 BLO and the Danish oil are the two things that I had heard recently, and the Danish oil is already here in the shop from a mother project so that is probably were I well end up. Quote
estesbubba Posted January 7, 2016 Report Posted January 7, 2016 Another benefit of Danish oil over BLO is it does have some varnish in it and will dry quicker. Here is mine completed with Danish oil. Quote
Popular Post Chet Posted January 8, 2016 Author Popular Post Report Posted January 8, 2016 Yesterday all I got done was notching out for the lower stretchers on the legs. I did this with my stack dado and miter gauge. I did the lowest point for the notch in three passes and then the highest point in three passes and then nibbled to the waste in between. Today I started by drilling all the holes for the hardware that holds the legs and aprons together, This is the front of the apron - It is setting up side down on my assembly table at this point. This is the back side of the apron and leg assembly with the ductile mounting plate screwed to the leg and the bolt threaded through from the front. After this I put the top on my assembly table, upside down and the lined up the two aprons were I wanted them and clamped them in place so I could cut the top and bottom stretchers and the top plate to size. While I had it like this I cut to size the interior portion of the top. This piece along with the top plates on the leg assemblies will make the whole top between the legs 3 inches thick. Top with the interior section attached Leg assemblies Legs and aprons assembled and setting upright for the first time. Top in place. Thats all for today. 10 Quote
..Kev Posted January 8, 2016 Report Posted January 8, 2016 Won't be long now! That's looking awesome! Quote
Chet Posted January 8, 2016 Author Report Posted January 8, 2016 Thanks guy! I can see the finish line in the coming up fast. 11 hours ago, estesbubba said: Another benefit of Danish oil over BLO is it does have some varnish in it and will dry quicker. Here is mine completed with Danish oil. Hey Mike the danish oil that you used, was that just the natural finish, no tint? Quote
estesbubba Posted January 8, 2016 Report Posted January 8, 2016 21 minutes ago, Chet K. said: Thanks guy! I can see the finish line in the coming up fast. Hey Mike the danish oil that you used, was that just the natural finish, no tint? Yup just Watco natural 1 Quote
shaneymack Posted January 8, 2016 Report Posted January 8, 2016 Chet you are smoking this thing man. How many hours have you put into it?? Sent from my SGH-I337M using Tapatalk Quote
Chet Posted January 8, 2016 Author Report Posted January 8, 2016 According to the article in Popular Woodworking this is supposed to be something you can do in a weekend but I am at about 32 hours. But I work slower then most and in the article they are using all dimensional lumber - 2 X12 Southern Yellow Pine so they aren't doing a lot of milling. Quote
wtnhighlander Posted January 8, 2016 Report Posted January 8, 2016 Chet, does this design include a lower shelf? I assume a stretcher is unnecessary with the wide aprons. Quote
Chet Posted January 8, 2016 Author Report Posted January 8, 2016 Yea the way the legs and internal apron are designed the thing is really stout, no real need for a stretcher. The original design has a shelf. I am going to eventually come up some sort of low profile storage (read drawers) for a plane till and other hand tools in place of the shelf, but I am going to work with the bench for a while and see what feels comfortable. I have even given some thought to having the drawer access from the two ends. The thing I am wondering is if you have something long vertically clamped in place on the apron and then you need to get into the drawer... Quote
wtnhighlander Posted January 9, 2016 Report Posted January 9, 2016 Seems like under the ends are places traditionally used to store holdfasts and cleats, from examples I have seen. Quote
Popular Post Chet Posted January 10, 2016 Author Popular Post Report Posted January 10, 2016 All I got done yesterday was drilling and mounting all of the hardware for the Top If some one was to make this, for the purpose of being able to break it down and store it, this is the components you would have: Two leg assemblies, two aprons and the top. First thing I did Saturday morning was glue up a blank for the crochet that goes on one end to hold work on edge. Then I started to drill all of the dog holes that this bench has. Five on the back edge of the top, seventeen in the front apron and two in one of the legs to store holdfasts. Once I get the Veritas surface mounted vice I will be doing another row of dog holes to work with the vice. Also once those holes are in place I will be able to hold work just about anywhere on the top. This is the jig for drilling the holes. The drill bit and bushing I got from Lee Valley, it is for the purpose of drilling dog holes, the bushing keeps everything straight. They come out real nice and clean. Dog holes in the top. Front apron. Holdfast Storage. Then I did the work on the crochet. Instead of making it out of the same wood as the rest of the bench I decided to do something different. I laminated some scraps of Oak, Walnut, Poplar and Bocote (I think, I am not sure, it has been around a long time). I cut it to shape on the band saw then worked a little with the rasp and then sanded it. Then I spent some time with my new low angle jack plane and flattened the top. This was my first effort at something like this so it took a while but came out well. And the final product. I am left handed so the crochet is on the right and the hole pattern on the apron is in the opposite direct from what it would be for a right handed person Taking the crochet for a test spin on a scrap of wood. I have to do a little final sanding in some spots and then put some danish oil on it. Then we'll start putting some dents in it. 9 Quote
wtnhighlander Posted January 10, 2016 Report Posted January 10, 2016 Chet, the bench looks great. Poplar is a good choice, I think. You have strengthened my resolve to incorporate more Nicholson features into my next bench. Well done! 1 Quote
Chet Posted January 10, 2016 Author Report Posted January 10, 2016 Thanks Ross. I would have used SYP like Al is using on his, but that stuff doesn't show up out here in California so poplar it is. I going to dent for sure but it is a work bench. Quote
..Kev Posted January 10, 2016 Report Posted January 10, 2016 That's awesome Chet! Very well done! 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.