JordanPatterson Posted January 18, 2016 Report Posted January 18, 2016 I have a full complement of tools in my shop (Table saw, Band Saw, Jointer, Planer, Routers, Drill press, Sander ect. ect.) but i have never owned a miter saw. I have a little money heading back into the shop and was considering one. I do projects ranging from remodeling my home to fine furniture and cant seem to gauge the usefulness of this tool. If you have one do you use it as a rough cut tool only or do you perform finish quality crosscutting with it? Does a slider or the Bosch glide system provide enough accuracy vs a non sliding saw? Quote
RichardA Posted January 18, 2016 Report Posted January 18, 2016 For me, a miter saw is for rough cutting only.... I've never used a Kapex, but I hear it's damn accurate! But the price keeps me far away from one! Quote
drzaius Posted January 18, 2016 Report Posted January 18, 2016 Generally speaking, a non-sliding saw will be more accurate because that are less parts involved that can introduce flex. Less capacity though. Quote
JordanPatterson Posted January 18, 2016 Author Report Posted January 18, 2016 2 minutes ago, RichardA said: I've never used a Kapex, but I hear it's damn accurate! But the price keeps me far away from one! I have heard the same. The Bosch glide saw is as pricey as I am willing to go. 1 minute ago, drzaius said: Generally speaking, a non-sliding saw will be more accurate because that are less parts involved that can introduce flex. Less capacity though. Is the accuracy of the non sliders table saw quality? I was leaning toward a non slider but those models seems to be at the bottom end of most company's miter saw lines. Quote
drzaius Posted January 18, 2016 Report Posted January 18, 2016 4 minutes ago, JordanPatterson said: Is the accuracy of the non sliders table saw quality? I was leaning toward a non slider but those models seems to be at the bottom end of most company's miter saw lines. It's bean long enough since I've looked at them that I couldn't say who makes a good slider. Most non-sliders you see are the cheapos, but there are probably good ones out there. Quote
Tom King Posted January 18, 2016 Report Posted January 18, 2016 Buy a cheap miter saw, and get a shooting board and plane. No excuse for lack of perfection then. Quote
Immortan D Posted January 18, 2016 Report Posted January 18, 2016 I have a Bosch Glide 12" and I use it for final crosscuts, miters and bevels. Only thing I never tried is compound miters. My saw is dead on, sliding or fixed, I have no complaints whatsoever. Quote
..Kev Posted January 18, 2016 Report Posted January 18, 2016 Many like the Bosch, I've never had one. I had a Dewalt and it was pretty good! Now I have a Kapex and love it! I will never have a shop without an SCMS. Different strokes for different folks tho. Quote
xxdabroxx Posted January 18, 2016 Report Posted January 18, 2016 I have a Dewalt compound miter saw and use it constantly in my remodeling. For finer woodwork it gets used to break down lumber to rough dimension. I don't know how I would live without it on the remodeling front. Quote
JordanPatterson Posted January 18, 2016 Author Report Posted January 18, 2016 So now the real question is. Bosch Glide for a large range an accuracy or a non sliding dewalt. its about a $330 difference. My main hang up with the cheap non slider is accuracy. I feel that the capacity isn't as important as i think it might be. Quote
xxdabroxx Posted January 18, 2016 Report Posted January 18, 2016 If you spend a little time tweaking the Dewalt you can get them pretty accurate. I still need to adjust my locking points on mine, 90 deg is a little off from the factory detent but I'm pretty sure it is adjustable. I just havent really had the need to yet. I usually throw a square on it before cutting anything too important because it gets carried around from in the house, to outside, to back in the shop. I've got a Freud blade on mine and it makes pretty decent cut. Quote
Woodenskye Posted January 18, 2016 Report Posted January 18, 2016 I have a hitachi 12" slider. I put a good blade and fine tuned and is extremely accurate in my opinion. The rail design allows it yo sit closer to the wall than most sliders. I looked at the Bosch Glide, the Kapex and Dewalt before I made my choice. I think I paid $399, so cheaper than the Bosch and Kapex. The dewalt just took up more space for the rails than I wanted. Quote
Gixxerjoe04 Posted January 18, 2016 Report Posted January 18, 2016 I have a 12" non sliding hitachi, works pretty well for $200. Would love a kapex but don't see myself ever buying one unless I hit the lottery. Quote
minorhero Posted January 19, 2016 Report Posted January 19, 2016 A non-sliding miter saw is generally speaking, far more accurate then a sliding miter saw. The need to keep a saw perfectly in line while also providing some method for it to move is not an easy engineering task, especially when folks are trying to keep it as cheap as possible as well so the hobbyist can afford it. I have used a non-sliding miter saw for finish level work for years. There are 2 important things to remember. 1) The blade it comes with is trash, buy a new blade for it right away. One designed for a miter saw, sliding miter saw, or radial arm saw would be best. Diablo makes a couple that work just fine. So you can get a decent 12" blade for under 100 dollars without trying hard at all. 2) in order to get accurate cuts you will need to build a miter saw station and install you miter saw in said station. You are going to need auxulary tables and fences on both sides of the saw and they of course need to be flat and square. So long as they are then you have a tool perfect for finish level work. I would not be without mine...ever. Next to my table saw it is probably the most used tool in my shop. My jointer and planer I only use when surfacing, but I will make several cuts on my miter saw as the piece progresses, first to just break it down, and then again to length. Sometimes there are intermediate steps as well where I will put joinery in when they are oversized in case I make a mistake and need to cut off the "bad" parts. I am moving my shop and purchased a 12" hitachi non-slider from Lowes. I got a good deal on it and its been a pretty good saw, though I admittedly haven't put it into a station yet so I haven't been able to give it the full workover. Still its doing fine so far and its got a lot of reviews online. The fence it has is fully adjustable as is the blade angle etc. Quote
knotscott Posted January 19, 2016 Report Posted January 19, 2016 I use my CMS mainly for things like long molding and really long pieces that don't fit on the TS. Otherwise it collects dust. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.