Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

End Grain Rounding With Hand Tools

Featured Replies

So far I've been using my belt sander or my router to round the end grain sides on a board. I wanted to do it with hand tools, so I put my block planes to work. Other than scratching the sole of my plane and some tear out, I'm not getting good results. I think maybe rasps could do the job, but mine are a bit on the coarse side so I didn't try them.

What's the best hand tool or technique for this task?

If I use hand tools I always do what you are doing. I use a block plane to establish the roundover, working in from both ends to avoid tear out, and finish with hand sanding. You can use a rasp as well and finish up with hand sanding it should work with little to no tear out.  As long as a router doesn't burn the end grain I just use a router though.

A hand plane would be my choice. You can get it 95% there & then finish with sandpaper. Sounds like your plane is not sharp enough though.

everything said already ... but he did ask what the _best_ hand-tool would be, so especially for a larger roundover >1/4" I'd say go 75% of the way with the block-plane, then to 99+% of the way with a moulding plane, finish with sand-paper if you really have to.

Assuming that your wood is not 'cumbly', i.e. brittle grain that breaks away, get the shape right with a very sharp block plane then go straight to an engineers file, preferably one that is a bit worn. Rub it down the grain, from high spot to low, in straight, even strokes, following the contour.

It will produce a surface that is ready for a mild abrasive, say 240 grit, followed by the finish of your choice. 

I've used this approach for 40 odd years and it works well on most timbers.

Good luck

Low angle block plane, and going the right direction will make all the difference in the world. Make sure your blade is nice and sharp. When I did my Roubo chop, I did the big chamfer with a block plane.

Yep, block plane.  If the wood is soft like fir or pine, hand tools have to be ridiculously sharp to slice fibers as opposed to just pushing then over.  If it is poplar or harder you handplane should do fine.  If not, sharpen.

GnG Low CoD (202).jpg

  • Author

Thanks guys. I thought my block plane was sharp enough but obviously I will have to double check that.

 

Can you easily shave with it? Needs to be that sharp for softwood.

Sharp, and wet the end grain with denatured alcohol - helps, but it is still s pain. 

  • Author
1 hour ago, sjk said:

And skew the plane

As a matter of fact the first plane I used on the edge was a skew block plane. And that's the one that got scratched (bronze...). So I switched to a regular block plane that could use some extra sharpening

 

1 hour ago, sjk said:
22 minutes ago, Eric. said:

 

Diablo 1/2 in. Rounding Over Bit

You kidding. That plane doesn't even have a handle!

 

  • 3 weeks later...

If it scratched the sole of your plane, my guess is there is still some grit from sanding (which will have a negative effect on whatever sharpening you did).  I had that happen on one of my first cutting boards, now my rule is sandpaper only after all the planing is done.

As far as tear out; always go from the long grain to the end grain with your strokes(or skew) and not the other way

For large radius, If the board in question is not too unweildy, and you could take the corners off quickly with the table saw with the blade set at 45 deg.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.