JosephThomas Posted October 28, 2016 Report Posted October 28, 2016 They look nice. Did you glue up all the panels from that same 2-2.5" wide stock? Looks like a lot of work... Quote
mat60 Posted October 29, 2016 Report Posted October 29, 2016 Allot more work than 1/4 ply but your 1/2 solid wood panels are a big step up and look great. Nice work Brad. 1 Quote
Popular Post bradpotts Posted November 16, 2016 Author Popular Post Report Posted November 16, 2016 They look nice. Did you glue up all the panels from that same 2-2.5" wide stock? Looks like a lot of work... I cut it down anywhere from 2 1/2 to 3". I also used 6/4 and cut it in half with the bandsaw to get two out of it. Finished the cabinets yesterday. I will take a picture when they are all installed. This is the island. 3 Quote
mat60 Posted November 16, 2016 Report Posted November 16, 2016 Your island looks great. Have they decided on the counter top? Look forward to seeing them installed. Quote
bradpotts Posted November 16, 2016 Author Report Posted November 16, 2016 Your island looks great. Have they decided on the counter top? Look forward to seeing them installed. I know they were going to go with granite but I am not sure if they were going to go with a light or dark. 1 Quote
logos Posted November 21, 2016 Report Posted November 21, 2016 They are Alder. stained and finished. Back. The gap is for wood movement because they are solid wood panels. I also made them 1/2 instead of 1/4 because that is what they wanted. I'm doing my first frame a panel now so this might seem like a silly question Are the 1/2 inch panels going into a 1/2 groove or did you cut a 1/4 tongue into the panel and using a standard 1/4 groove? Quote
Popular Post bradpotts Posted November 21, 2016 Author Popular Post Report Posted November 21, 2016 I'm doing my first frame a panel now so this might seem like a silly question Are the 1/2 inch panels going into a 1/2 groove or did you cut a 1/4 tongue into the panel and using a standard 1/4 groove? I cut a quarter inch tongue to fit into the quarter inch grove. I actually made them with a shaker door set and used that bit to cut everything. Style, rails and panel. Got these babies installed. I will take some more pictures once the appliances and countertops are installed. 8 Quote
Chestnut Posted November 21, 2016 Report Posted November 21, 2016 Hey looks good. I just started some cabinet work last night. It's awesome how fast they go together compared to furniture. 1 Quote
..Kev Posted November 21, 2016 Report Posted November 21, 2016 Very nice Brad! Be proud of the work! 1 Quote
shaneymack Posted November 21, 2016 Report Posted November 21, 2016 Looks great, Brad. Nice work ! Sent from my SM-N910W8 using Tapatalk 1 Quote
JosephThomas Posted November 21, 2016 Report Posted November 21, 2016 Good stuff Sent from my Nexus 5 using Tapatalk 1 Quote
Chet Posted November 21, 2016 Report Posted November 21, 2016 Looks like she is taking that sanding task seriously. Quote
logos Posted November 21, 2016 Report Posted November 21, 2016 I cut a quarter inch tongue to fit into the quarter inch grove. I actually made them with a shaker door set and used that bit to cut everything. Style, rails and panel. Got these babies installed. I will take some more pictures once the appliances and countertops are installed. These turn out awesome! Do you remember the brand of raised panel bit you used? I take it you used a standard slot cutter and the fit the raised panel and not a shaker style tongue and groove bit as well 1 Quote
bradpotts Posted November 21, 2016 Author Report Posted November 21, 2016 These turn out awesome! Do you remember the brand of raised panel bit you used? I take it you used a standard slot cutter and the fit the raised panel and not a shaker style tongue and groove bit as well I used a whiteside shaker bit. I used the grove cutter to cut the tongue too. 1 Quote
pkinneb Posted November 21, 2016 Report Posted November 21, 2016 That's a lot of cabinets. Nice job! 1 Quote
bradpotts Posted November 22, 2016 Author Report Posted November 22, 2016 Looks like she is taking that sanding task seriously. I told her she couldn't eat until she was done sanding them all. Quote
Popular Post bradpotts Posted November 22, 2016 Author Popular Post Report Posted November 22, 2016 Here are a couple things that I learned throughout building these cabinets. Hopefully this will be helpfully for the next person who builds them. 1. Make sure you have enough space to store the cabinets. I had two unused rooms that I kept them in. 2. Don't stain the cabinets. Unless you have to like I did. If you do stain them, do not follow the cans advice and sand with #0000 steel wool. The wool will get stuck in some of the grain and it will look like you have hairs in your finish. 3. The Kreg door hole jig works really well, especially if you plan on finishing the doors before drilling the holes. 4. Make sure if you are doing cabinets with a face frame you DON'T buy side mounting hinges. 5. If you want to get better at spray finishing, build a kitchen of cabinets. 6. Use a #6 3/4 screw to screw the door in. When you are putting the doors back on during instalation use a #8 3/4 screw. Here is the process that I used to build the cabinets I started off the process by taking measurements of the kitchen. I designed the kitchen with the owner. I then built the design in Sketchup. I labeled all of the cabinets with a letter. This came in really handy. I don't have any cut hardware, so I did it the old fashion way. I took a pice of paper and cut it into 3" by 6" squares. Every 1/16" is equivalent to an inch on the plywood. This allowed me to see how many pieces of plywood I would need to buy. There was about 35 liner feet and I bought 10 3/4" sheet and 8 1/4" sheets. I ended up with one extra of each. After cutting out the sheet goods, I stained them and finished them. I did this because I didn't want to try and spray inside the boxes. I cut a dado in the sides and backs of the cabinets for the 1/4" plywood. Then I attached the sides to the top and bottom with dominos. I made a jig for the domino to come down from the top and bottom 3/4" on the upper cabinets. I also made a jig for the bottom of the base cabinets to cut the dominos in the sides. By jig, it was just a fence set at the distance from the edge I needed. Once that was all done, I cut pocket holes in the bottom of the base cabinets. I did this so I didn't have to try and get a clamp on the cabinets. I glued the dominos in and screwed the pocket holes to hold it together while the glued dried. After they were glued together, I made the face frames and again used dominos. I made the doors with a standard saker door bit set. To figure out how big to make the doors, I took the size of the inside of the face frame and doubled the size of the overhang hinge I was using. I made the doors 1/2" instead of 1/4" because I wanted them to look heavier. I also used hard wood for the doors. I left about 1/16 on each side to allow for movement. I used the kreg door hole jig to cut the holes for the hinges. The drawers were pretty straight forward. I used a porter cable jig to cut the dovetails and put a 1/4" plywood bottom in. I made the shelves out of solid wood at 1/2". I used oil modified water based minxwax poly to finish them. Cost of the job: There was about 35 liner feet of cabinets. I spent $3858. So it came to about $111 a liner foot. I used about 300bf of alder. I used 248 6 Quote
mat60 Posted November 22, 2016 Report Posted November 22, 2016 You have done great with your cabinet job. I enjoyed seeing this project. Thanks 1 Quote
Alan G Posted November 23, 2016 Report Posted November 23, 2016 The cabinets really turned out nice. Are you going to add strips of ply across the tops of the cabinet boxes to allow for a connection to the countertop? Usually the are 3-4" wide strips that finish flush with the top of the carcass which allow for either caulk or a mechanical fastener . Lastly, what is your estimation of time spent on this project from design all the way thru install? Thinking of doing my own kitchen so just curious. really great job! Quote
bradpotts Posted November 23, 2016 Author Report Posted November 23, 2016 The cabinets really turned out nice. Are you going to add strips of ply across the tops of the cabinet boxes to allow for a connection to the countertop? Usually the are 3-4" wide strips that finish flush with the top of the carcass which allow for either caulk or a mechanical fastener . Lastly, what is your estimation of time spent on this project from design all the way thru install? Thinking of doing my own kitchen so just curious. really great job! Yes I am going to add plywood for the countertops. It probably took me about 300 hours. It also depends on what size granite they want. Quote
Chestnut Posted November 23, 2016 Report Posted November 23, 2016 Thanks for the advice @bradpotts . I feel like you used a LOT of solid wood but then again there are a lot of cabinets in that kitchen. I grabbed 125 BF for mine but i think I'm going to use 1/2" Baltic for the drawers. #1 above is a concern for me i don't have a ton of storage space and to get around that because it's for my own house I'm going to do the build in parts build lowers and remodel and install and then build uppers after everything is up and running. #2 I decided to go with pre finished ply and after working with it there are a few hurdles but man is it going to be nice to just have to finish the face frame and the doors. It's going to make this way faster and easier. #6 is good advice I'll remember that thanks. Cabinets look good installed! 2 Quote
Alan G Posted November 23, 2016 Report Posted November 23, 2016 Have you made cabinets for a full kitchen before? If not, would you do it again? Quote
bradpotts Posted November 24, 2016 Author Report Posted November 24, 2016 Have you made cabinets for a full kitchen before? If not, would you do it again? This is the first time I have done a whole kitchen. I have made cabinets for my shop. I would do it again for the right price. Thanks for the advice @bradpotts . I feel like you used a LOT of solid wood but then again there are a lot of cabinets in that kitchen. I grabbed 125 BF for mine but i think I'm going to use 1/2" Baltic for the drawers. #1 above is a concern for me i don't have a ton of storage space and to get around that because it's for my own house I'm going to do the build in parts build lowers and remodel and install and then build uppers after everything is up and running. #2 I decided to go with pre finished ply and after working with it there are a few hurdles but man is it going to be nice to just have to finish the face frame and the doors. It's going to make this way faster and easier. #6 is good advice I'll remember that thanks. Cabinets look good installed! Yeah doing them with prefinished plywood have saved tons of time. I think I went through five gallons of finish. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.