freedhardwoods Posted October 23, 2016 Report Posted October 23, 2016 One of the cabinet shops in the area bought about 1,500 lbs of "reject" deck screws and they are selling them in 23 lb boxes. The pic shows a 5 lb box I paid $30 for a year ago beside a box with 24.5 lbs in it I paid $40 for. He didn't have any 4" screws boxed up, so he grabbed an odd box beside him and when he slightly over filled it, he said "close enough". Altogether I've bought 5 boxes of 4 different sizes. 2" - $30, 2.5" - $35, 3" & 4" - $40 I got 2 boxes of 3" since I use more of them. 1 Quote
..Kev Posted October 23, 2016 Report Posted October 23, 2016 That otta keep you in screws for a while! Quote
freedhardwoods Posted October 23, 2016 Author Report Posted October 23, 2016 I haven't used 1 nail in my shop build; all screws. 1 Quote
Llama Posted October 23, 2016 Report Posted October 23, 2016 21 minutes ago, Lester Burnham said: Lots of "screwed" jokes could be in play here. But I'll just say, good find. It is so tempting!!! Quote
shaneymack Posted October 24, 2016 Report Posted October 24, 2016 1 hour ago, freedhardwoods said: I haven't used 1 nail in my shop build; all screws. You dont have a framing nailer? Quote
wtnhighlander Posted October 24, 2016 Report Posted October 24, 2016 I'm with the OP - screws over nails, exery time. Especially doing 'lone wolf' framing, it is a lot easier to hold a rafter / joist in place and drive a screw, than to swing a hammer. And no, Shane, I don't own a framing nailer. Quote
JosephThomas Posted October 24, 2016 Report Posted October 24, 2016 What exactly makes them "rejects"? I guess if I saw that word used I would assume it wasn't as strong as it should be, so I'm curious. Quote
Tpt life Posted October 24, 2016 Report Posted October 24, 2016 Just beware... screws are often not in the code because of the tendency to snap under shear load and shifting. This does not mean snapping is going to happen, only that it is more likely. 99% of the time (made up stat based on limited experience) using screws just takes more time. That little bit that is left is inappropriate usage. I am not saying don't do it, just beware of the downside. Quote
shaneymack Posted October 24, 2016 Report Posted October 24, 2016 Just beware... screws are often not in the code because of the tendency to snap under shear load and shifting. This does not mean snapping is going to happen, only that it is more likely. 99% of the time (made up stat based on limited experience) using screws just takes more time. That little bit that is left is inappropriate usage. I am not saying don't do it, just beware of the downside. Exactly. Screws are not for framing. The only advantage of screws over nails for framing is pulling two pieces together but that's what ardox nails are for. I'd be surprised if code allowed screws for framing in tornado and earthquake areas. Sent from my SGH-I337M using Tapatalk Quote
wtnhighlander Posted October 24, 2016 Report Posted October 24, 2016 You guys just HAD to go and bring CODE into the discussion! Quote
JosephThomas Posted October 24, 2016 Report Posted October 24, 2016 Lulz Sent from my Nexus 5 using Tapatalk Quote
xxdabroxx Posted October 24, 2016 Report Posted October 24, 2016 24 minutes ago, Chestnut said: If he was in CA he would have about 10 more books that size to cut in half. Quote
Brendon_t Posted October 24, 2016 Report Posted October 24, 2016 8 minutes ago, xxdabroxx said: If he was in CA he would have about 10 more books that size to cut in half. That was just the book that covers regulations for outhouses.. 1 Quote
Chestnut Posted October 24, 2016 Report Posted October 24, 2016 I didn't think that outhouses would be allowed in CA? Doesn't all solid waste have to be recycled and all liquid waste gets processed and pumped back into the drinking water system both getting fed right back to you? Quote
BonPacific Posted October 24, 2016 Report Posted October 24, 2016 40 minutes ago, Chestnut said: I didn't think that outhouses would be allowed in CA? Doesn't all solid waste have to be recycled and all liquid waste gets processed and pumped back into the drinking water system both getting fed right back to you? As opposed to what? Pooping in the woods, fertilizing a blackberry bush, and then eating those blackberries? Everything gets recycled/processed and re-consumed, just a matter of where and how quickly. Quote
Chestnut Posted October 24, 2016 Report Posted October 24, 2016 7 minutes ago, BonPacific said: As opposed to what? Pooping in the woods, fertilizing a blackberry bush, and then eating those blackberries? Everything gets recycled/processed and re-consumed, just a matter of where and how quickly. I was making a joke because what i said is what happens everywhere. Wastewater treatment plants separate out their bio solids and sell it to local farmers that use it as fertilizer. They then dump the treated water in a stream to the next city to be picked up by water treatment, treated and piped to your house. The joke is that they need as much recycled water as possible because of the massive drought. Quote
BonPacific Posted October 24, 2016 Report Posted October 24, 2016 42 minutes ago, Chestnut said: I was making a joke because what i said is what happens everywhere. Wastewater treatment plants separate out their bio solids and sell it to local farmers that use it as fertilizer. They then dump the treated water in a stream to the next city to be picked up by water treatment, treated and piped to your house. The joke is that they need as much recycled water as possible because of the massive drought. Miss-read your joke, overreacted a little, must be spending too much time hearing about the election. 1 Quote
xxdabroxx Posted October 24, 2016 Report Posted October 24, 2016 In other news, next years version of the building code (yeah its bigger and worse than last cycle) will allow the use of grey water for irrigation. It was only allowed on a case by case basis as approved by the local building officials before. We're supposed to be net zero energy usage for residences by 2020. What is this affordable housing I so often hear of? We've also reduced the flow amount of faucets so much that they are starting to have problems with things like toothpaste building up in the "P" traps. Then there is the exhaust fan that has to run all the time to keep the indoor air quality up because we have sealed the houses up so tight they don't breath and create unhealthy interior environments. I hate this state for so many reasons, but it is so hard to leave. I'm also curious as to what makes them rejects? Left hand threads? LOL that would screw the new guy up. Quote
freedhardwoods Posted October 24, 2016 Author Report Posted October 24, 2016 I don't have much use for codes. They are usually ridiculous rules that defy common sense. There are dozens of carpenter crews in this area. They have to follow the codes in whatever area they're building in, but I've heard for years screws hold better than nails. Until a couple years ago, in this county, you didn't need a permit to build anything. Now, they want you to get one if you're putting up a big building. 2 Quote
Tpt life Posted October 24, 2016 Report Posted October 24, 2016 I'm in your state. I have yet to see a code that defies common sense. I also was careful as the nail vs screw can be a bit of a hot boast fest. Just know the limitations of the product. I have been out to fix decks with snapped screws. Quote
BonPacific Posted October 24, 2016 Report Posted October 24, 2016 13 minutes ago, C Shaffer said: I'm in your state. I have yet to see a code that defies common sense. I also was careful as the nail vs screw can be a bit of a hot boast fest. Just know the limitations of the product. I have been out to fix decks with snapped screws. I think some of the issue stems from the forming methods of both. Cheap screws are cast, but even cheap nails are still formed from extruded metal. Stupid people will try and frame their house with drywall screws because they're cheaper. The Code is there to reduce the chance of either idiots or con-men building your house. It's not perfect, but it helps. Quote
freedhardwoods Posted October 24, 2016 Author Report Posted October 24, 2016 I have had screws snap just trying to drive them in, so I know they are more brittle than nails. I switched from nails to screws several years ago because nails eventually loosen. I replaced a 16x32 deck with nail heads sticking out everywhere 2 years ago. Nothing coming apart yet. As far as the reject description of the screws I bought, I haven't found anything wrong yet. Maybe the corrosion resistant coating wasn't right. Quote
shaneymack Posted October 24, 2016 Report Posted October 24, 2016 I have had screws snap just trying to drive them in, so I know they are more brittle than nails. I switched from nails to screws several years ago because nails eventually loosen. I replaced a 16x32 deck with nail heads sticking out everywhere 2 years ago. Nothing coming apart yet. As far as the reject description of the screws I bought, I haven't found anything wrong yet. Maybe the corrosion resistant coating wasn't right. Next framing project you have try a framing gun with nails with some hot dipped or brite coating on them. Never in a million years will those things loosen. The heads bend before the nail pulls out. Sent from my SM-N910W8 using Tapatalk Quote
wtnhighlander Posted October 25, 2016 Report Posted October 25, 2016 Local building codes in my area banned the use of nail guns for many operations (mostly roofing) because the single insertion impact apparently splits the wood fibers, rather than breaking through them, resulting in a weaker hold. This ban happened after the first tornado to hit the area in several decades left a 15-mile swath of destruction. I don't know if coated nails were common at the time. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.