Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Cold shop concerns

Featured Replies

I work in a cold, barely insulated shop.  It's a 2.5 car garage, attached to the house, unheated.   We are planning on using almost the entire thing for shop space.  The garage door is 'leaky' and uninsulated.   Since it's a rental house, modifying things to get some heat, even minimal, really isn't an option.  It's currently 17f out here, and thats decently warm for this past week. 

I've read some threads on getting heat into a shop, but not much on what to be aware of in a cold shop.  I know finishing will take longer to cure, if it even does.  Same with glues and epoxies.  I have a really nice face shield for turning on the lathe, but it fogs up so quick, I can't use it in the cold.  

What specific hazards and limitations should I be aware of in this situation? 

 

Thanks folks. 

Get a propane heater in there, you might also look at putting up some rigid foam insulation in the garage door.  You could always double sided tape it then remove it if it is an issue when you move.  I think it would be worth it if you are going to be there very long, it will also help in the summer. 

I think I would keep my glues inside, just take them out for the glue up process.  I wouldn't even try to finish anything in temperatures below what the manufacturer of the finish recommends.  Try some rainX on your face shield, there are also some anti-fogging lens cleaners for prescription glasses that work well. 

Bring the finishes and glues indoors..

I take my batteries in so that they don't get super cold, but I'm not sure if it matters. I know contractors who keep their cordless equipment in the back of their pick-up in all temps without problems.

IMO it's not good to do woodworking when your fingers are numb (and your snot is freezing on the tip of your nose). And wearing gloves isn't really a viable option. Once again, I know that carpenters on a job-site do it all the time, but I try to avoid gloves when I'm operating power tools.

Sometimes it's tough to put on the ear muffs when it's below freezing. Someone really should start producing heated blue-tooth-enabled ear protection, then I would keep them on all the time.

In addition to what was said about glue and finishes, my jojoba oil thickens quickly when it is cold. I don't bring it indoors, but I stick it in front of the space heater for a few minutes when I'm oiling a hand plane or whatever.

It may not apply to your situation but in winter I quit using the slop sink and put some RV anti-freeze in the trap. I take in all finishes, glue, aerosols, waxes, putties, spackling, etc. for the duration...

I keep my nail guns in a temp controlled area.

 

 

 

 

 

Cold is the enemy of depleted batteries. Fully charged is not supposed to be an issue. I don't push it, but like you said left company tools in an unheated trailer. 

3 minutes ago, wdwerker said:

I would bring any wood needing to be glued up inside to acclimate before gluing up indoors.

Yeah, I do all glue-ups indoors, then I don't have to heat the shop overnight.

It Would be hard for me to give advice. They would shut our city down if it ever got below 29*. Which reminds me, I plan on going to the Amana Iowa woodworking show in mid May. Will there be a thaw before then?

Here's a drastic option.  Put down 1" foamboard on the floor.  Float a tongue and groove plywood floor on top.  Build walls and a ceiling inside of your walls and under the garage door frames.  Insulate the crap out of it.  Run outlets and lights wherever you darn please.  Won't take much heat to get it to 50F.

Two tips. First, an inexpensive electric heater is better than no heater. Second, if your lathe mask dogs up it is because your breath is hitting the cold shield and condensing because of the shield' scolded temperature. If you were to get some sort of heater, you could just hold your shield in front of it for a bit whenever it started to fog and the warmer shield would not be as prone to condensation.

Also, don't be afraid to ask the landlord if they mind you putting insulation on the garage door. Most of the time it is removable and the landlord might like it and want it to stay, maybe even give you a break on rent to offset the cost that month. Many landlords don't mind small things like that if they improve the property. I've had friends who wanted to insulate the garage in a rental and when they asked the landlord about it, the landlord (who bought the property as an investment only) didn't even know it wasn't insulated. He ponied up the cash and had it done the following month because it would be a good ROI for him.

You might also make something for them (if it's an individual or couple and not a property management company) as a pre-thank-you before you ask. 

You'll be happier in the long and short term if you do some basic heat-sealing/insulation. Like a few people mentioned, your landlord might be happy to let you insulate, or help with the costs of doing so. Weatherstripping the garage doors would be my first job, followed by adding rigid foam to the panels. That alone will get you a few degrees, and should be possible for under $100.

if your landlord isn't willing to let you make permanent upgrades, seal the doors with tape and plastic. You can buy kits specifically for this, or just use duck tape and plastic sheet. With sealed and insulated doors, even a small electric heater should be able to keep you above freezing.

In terms of things to watch out for, I'd definitely remove any liquids or gels from the shop. Oils and such won't likely be damaged by the cold, but they won't really be usable out there. Glue and Finishing should be done inside. That said, if you keep PVA warm for the first hour or two, it should be able to finish curing even if put back into an unheated space.

Keep in mind that not only is it cold, but the humidity out there is going to be very low, so take extra care if you're doing panel glue-ups or anything else susceptible to movement. 

When I worked in an unheated shop (not as cold as Ohio) i found that setting a heater under my primary bench was the only way to work comfortably. I would compress the area of the shop I used down to about 3/4 of a stall. Find a favored station, and set it up with a heater that lives there and can heat, or at least take the chill out of, the immediate area in twenty minutes or less.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.