Recommended Posts

Posted

Hey guys, I have one of those old craftsmen 113 series table saw that Needs a fence upgrade.what would y'all recommend? I like the biesemeyer but my only concern is that I want to upgrade my table saw (probably to a sawstop) some day and I don't know if I want to spend $400 on something I am most likely not going to use once get a new saw. As always any advice will be much appreciated. Thanks,Lewis 

 

 

Posted

The theory is that a good fence can follow you from saw to saw.  This may hold true for some or even most.  My Beis went with my old saw when i got a Saw Stop.  Getting the saw without the fence turned out to be a no-go with the saws I was looking at. I didn't want the hassle of selling one fence or the other to recover some of my costs but, that could certainly be an option.

That being said, by the time you get a VSCT fence setup, you are in for a good piece of change.  They are very cool (no pun intended) but, there are other options out there as well. 

If the extrusion is attractive to you, the VSCT fence is the way to go.  I replaced my faces with extrusions but found I didn't use the t-slots the way I thought I would (and I'm a big-time jig using sorta guy) so I switched back. YMMV.

For my old 113. I added an Align-a-Rip for about $150 and it was a big step up.  It too went with the saw but, I did get about 60% of the cost of it back.  Unfortunately I don't find fences in this category at this price anymore. Most decent fence systems with rails are going to start near the $300 mark

Posted
9 hours ago, Lewis Allison said:

 I like the biesemeyer but my only concern is that I want to upgrade my table saw (probably to a sawstop) some day and I don't know if I want to spend $400 on something I am most likely not going to use once get a new saw.

A couple of months ago I swapped out my biesemeyer style fence for the VSCT.  For me, it was a great upgrade.  However my concern, if you are going to buy a new saw, why not save and wait.  I inherited an old Craftsman from my grandfather 30+ years ago and I had to use a C clamp on the rear of the fence to use the saw.  Not the greatest solution but I used it that way until I was able to buy a replacement saw.  If your fence is usable, don't replace it, wait until you can buy a new saw.

Posted
3 hours ago, Woodenskye said:

I will say the Vega Fence, I have the Vega 40, which may not be made anymore, but is good and easy to install.

Another vote for the Vega. They bolt directly onto craftsman saws.  Big improvement over stock.

  • Like 2
Posted
11 hours ago, Just Bob said:

 However my concern, if you are going to buy a new saw, why not save and wait.  I inherited an old Craftsman from my grandfather 30+ years ago and I had to use a C clamp on the rear of the fence to use the saw.  Not the greatest solution but I used it that way until I was able to buy a replacement saw.  If your fence is usable, don't replace it, wait until you can buy a new saw.

I have thought of that, but I hate using that fence so much that I try to avoid using the table saw for ripping whenever possible, I have taken to doing all my ripping on the bandsaw. Plus I don't see myself getting a new saw any time soon. So that's why I decided to spend a few hundred dollars now on a fence and upgrade the saw in a couple of years.

  • Like 1
Posted
2 hours ago, Lewis Allison said:

I have thought of that, but I hate using that fence so much that I try to avoid using the table saw for ripping whenever possible, I have taken to doing all my ripping on the bandsaw. Plus I don't see myself getting a new saw any time soon. So that's why I decided to spend a few hundred dollars now on a fence and upgrade the saw in a couple of years.

I've heard that bandsaw lovers prefer to rip (and do most of their cuts) on the bandsaw - it's safer, with no kickback, etc.  In my case I don't have a usable bandsaw fence (I use a shop made jig with C-clamps)  so I prefer to rip with the table saw.   At least I can agree on the value of a fence!

Posted

I have the Delta T-2 on my 113 Craftsman, and it has been great.  I have hand it for about 5-6 years now, and it has been great. I haven't used the T-3, but it looks like they made some nice improvements.  

My only caution is that Delta as a company isn't what they used to be, so that may be something to consider when you are buying.  But for under  $200, it is hard to go wrong.

  • Like 1
Posted

i put a Vega 26 on my 113, it changed the saw for the better. the original fence was something i fought with constantly.

i believe any aftermarket fence will make your saw a much more usable tool. more accurate, more repeatable cuts, etc...

i have read good things about the T2, which is less $$ than most of the other options, if it is still availible. the Vega is a direct bolt on, if that matters.

Posted

I have been using a Vega fence for around 25 years. Once I needed some small part, called and ended up talking to the owner, parts arrived in a few days. I've been quite happy with it.

Posted
i put a Vega 26 on my 113, it changed the saw for the better. the original fence was something i fought with constantly.

i believe any aftermarket fence will make your saw a much more usable tool. more accurate, more repeatable cuts, etc...

i have read good things about the T2, which is less $$ than most of the other options, if it is still availible. the Vega is a direct bolt on, if that matters.

 

 

I have a Delta T2 and I love It !

 

 

Sent from my iPhone using Tapatalk

Posted
On 3/16/2017 at 7:14 AM, Woodenskye said:

I will say the Vega Fence, I have the Vega 40, which may not be made anymore, but is good and easy to install.

 

On 3/16/2017 at 10:49 AM, Brendon_t said:

Another vote for the Vega. They bolt directly onto craftsman saws.  Big improvement over stock.

Another vote here for the vega. I've got an old craftsman 113 direct-drive saw and I put the Vega U40 on it (got it for Christmas this past year) and it has been a game-changer. The only thing with mine is that I had to drill an extra hole into the back support bar to accommodate the rod that the guard/splitter attach to. this means, of course, that I can't use those but the guard was clunky and I am going to get a micro jig splitter for my insert instead.

http://vegawoodworking.com/product/table-saw-fence/

It looks like they don't make the U40 any longer but I'm sure the U26 or the U50 would both work just fine, depending on the rip capacity you need/want. Or you could get the Pro 40... but I'm not sure if there's a difference in how it bolts on that might not work with a 113.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.