collinb Posted May 22, 2017 Report Posted May 22, 2017 A number of table saws have the big bump access door on the side. I'm curious why it is a bubble instead of just a door? Quote
Eric. Posted May 22, 2017 Report Posted May 22, 2017 Some part of the internals will swing into that space when you tilt the blade. I'm not familiar with that saw so I'm not sure which part, but that space is reserved for something. Quote
gee-dub Posted May 22, 2017 Report Posted May 22, 2017 When you tilt the blade the trunnion and motor have to go somewhere. 1 Quote
BonPacific Posted May 22, 2017 Report Posted May 22, 2017 19 minutes ago, Eric. said: Some part of the internals will swing into that space when you tilt the blade. I'm not familiar with that saw so I'm not sure which part, but that space is reserved for something. Spot on. I have a cousin of this saw, and the motor mount swings into that space. I suppose they could have made the cabinet itself a bit wider, but I'm not sure it would make a difference once way or another. Quote
Eric. Posted May 22, 2017 Report Posted May 22, 2017 5 minutes ago, BonPacific said: I suppose they could have made the cabinet itself a bit wider I guess plastic is cheaper than...plastic? LOL 1 Quote
Vyrolan Posted May 22, 2017 Report Posted May 22, 2017 35 minutes ago, BonPacific said: Spot on. I have a cousin of this saw, and the motor mount swings into that space. I suppose they could have made the cabinet itself a bit wider, but I'm not sure it would make a difference once way or another. Making the whole cabinet wider would push the legs in that direction...and then you'd have the main mass and all the force of the spinning off-centered compared to the base which is probably not good for balance/wobble/vibration. 1 Quote
knotscott Posted May 23, 2017 Report Posted May 23, 2017 The angled bottom funnels saw dust too. Quote
BonPacific Posted May 23, 2017 Report Posted May 23, 2017 18 hours ago, knotscott said: The angled bottom funnels saw dust too. Not very well if the internals are anything like an r4512. Quote
Denette Posted May 23, 2017 Report Posted May 23, 2017 Not very well if the internals are anything like an r4512. I dunno, my 4512 does a pretty good job of it. It piles up in the corners, but never gets past a certain point. But, then, I've also sealed every point on the saw but the blade - the interior of my saw is pretty airtight, so maybe it's my paranoid leak sealing that makes mine work. Quote
BonPacific Posted May 23, 2017 Report Posted May 23, 2017 2 minutes ago, Denette said: I dunno, my 4512 does a pretty good job of it. It piles up in the corners, but never gets past a certain point. But, then, I've also sealed every point on the saw but the blade - the interior of my saw is pretty airtight, so maybe it's my paranoid leak sealing that makes mine work. Interesting. I've sealed mine up pretty well, but it still tends to pileup in that side cavity. Not that it impedes the function at all, but *shrug*. Maybe it'll be better now that I vent outside and the draw from my DC has been boosted. Quote
Eric. Posted May 23, 2017 Report Posted May 23, 2017 Actually, sealing up a table saw too much can impede DC performance. It chokes out both CFM and velocity, especially if you have everything sealed off AND use a ZCI. There's basically no way for the system to pull enough air. I've sealed off parts of mine but left a few carefully chosen areas open for flow. Quote
Denette Posted May 23, 2017 Report Posted May 23, 2017 Actually, sealing up a table saw too much can impede DC performance. It chokes out both CFM and velocity, especially if you have everything sealed off AND use a ZCI. There's basically no way for the system to pull enough air. I've sealed off parts of mine but left a few carefully chosen areas open for flow. Yeah, I guess I should clarify that I do not use a zero clearance insert. That would pretty much kill my dust collector with the current level of airtightness Quote
Tpt life Posted May 23, 2017 Report Posted May 23, 2017 Drill a hole in the pile spot. This is so simple but never seems to occur to anyone. Air flowing in at that point will keep a pile from forming there. A few tiny holes is all it takes. Quote
Popular Post Eric. Posted May 23, 2017 Popular Post Report Posted May 23, 2017 2 minutes ago, Denette said: Yeah, I guess I should clarify that I do not use a zero clearance insert. That would pretty much kill my dust collector with the current level of airtightness And ultimately, most saws suck for DC regardless of what you do, until you add an over-the-blade type deal. Then it's annoying because there's something in your way all the time. At least I find it annoying. 3 Quote
Denette Posted May 23, 2017 Report Posted May 23, 2017 And ultimately, most saws suck for DC regardless of what you do, until you add an over-the-blade type deal. Then it's annoying because there's something in your way all the time. At least I find it annoying. Yup. Not to belittle safety, but I can't think of a shop I've been in that had a blade guard on the table saw, much less a dust collection arm. I always chuckle when I watch videos where the caption "safety guards have been removed for photographic purposes only" pops up. No they weren't, haha. Quote
Popular Post Eric. Posted May 23, 2017 Popular Post Report Posted May 23, 2017 I'm honestly of the opinion that a lot of the time a blade guard actually makes it more dangerous, because you can't see what's going on in the business area nearly as well. I tried using mine when I first got my saw and ran into a number of situations that made me realize...I don't like it. I feel much safer when I have an unobstructed line of sight. I know where my fingers are, I know where the blade is, and I can see everything that's happening. 8 Quote
wtnhighlander Posted May 24, 2017 Report Posted May 24, 2017 And with a blade guard in place, narrow rips with a push block (Grrrtipper style) are nearly impossible. Quote
drzaius Posted May 24, 2017 Report Posted May 24, 2017 I used to hate guards, but now that I have a good one, it's always on the saw unless it's a non-through cut or a rip too close to the fence. And with it on, the dust collection is close to 100%. Quote
collinb Posted May 24, 2017 Author Report Posted May 24, 2017 I should have thought about the tilt. (I do it so seldom.) Tx all. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.