Andy Faust Posted May 26, 2017 Report Posted May 26, 2017 Looking to buy my fist table saw. I've just graduated from cabinet making trade school and looking to make a garage shop. I don't have 220 on l10 but I could pay to have it put in if you think it's worth the investment. Looking for a cabinet saw not a job sight. Looking to spend under 1,500 1 Quote
Eric. Posted May 26, 2017 Report Posted May 26, 2017 Most cabinet saws are going to require 220. Best bang for your buck in that price range is the Grizzly G0690. Be prepared to replace the fence. 1 Quote
OldSouthWoodCraft Posted May 26, 2017 Report Posted May 26, 2017 Getting a simple 220 circuit ran wouldn't be too expensive or require much work depending on your shop set up and location. But I definitely second the remark about the Grizzly. Well worth the money and if you can afford try and get a Biesemeyer fence. I think they are in the 200 to 300 range. Sent from my SM-G950U using Tapatalk Quote
Eric. Posted May 26, 2017 Report Posted May 26, 2017 The fence that comes on that Grizzly is a Biese clone and has the same potential problems that all Biese clones have: many of them are not straight because of the way the UHMW plastic is bolted to the tube steel. For my money, a better upgrade is a VSCT fence. They're superior to the Biese in every way...except the dainty little handle, which I replaced. https://vsctools.com/shop/product-category/table-saw-fence/ Quote
Cliff Posted May 27, 2017 Report Posted May 27, 2017 5 hours ago, Eric. said: Most cabinet saws are going to require 220. Best bang for your buck in that price range is the Grizzly G0690. Be prepared to replace the fence. Yours is the g0690 right? You should upgrade, I'll come get your old one. I've been thinking I need a used cabinet saw until I can save for the endgame saw. Quote
Eric. Posted May 27, 2017 Report Posted May 27, 2017 16 minutes ago, Cliff said: Yours is the g0690 right? You should upgrade, I'll come get your old one. I've been thinking I need a used cabinet saw until I can save for the endgame saw. I'll take $3,899.00 for it. The Griz has been a good saw. Replaced the fence and I've had zero complaints since. I'd like to get my kids in the shop one day and I might upgrade to the SS at that point...but if it wasn't for that I'd just keep going with this saw indefinitely. Quote
Cliff Posted May 27, 2017 Report Posted May 27, 2017 12 minutes ago, Eric. said: I'll take $3,899.00 for it. The Griz has been a good saw. Replaced the fence and I've had zero complaints since. I'd like to get my kids in the shop one day and I might upgrade to the SS at that point...but if it wasn't for that I'd just keep going with this saw indefinitely. It does that well for ya? I can probably locate one used somewhere or just pick up a new one for a few years. Mine is just.. awful. Quote
Eric. Posted May 27, 2017 Report Posted May 27, 2017 12 minutes ago, Cliff said: It does that well for ya? I can probably locate one used somewhere or just pick up a new one for a few years. Mine is just.. awful. Well, let's make sure we just acknowledge once more...that I've had problems with almost every Grizzly tool I've owned...except the table saw. The only one I gave up on so far has been your jointer, but I've had a range of issues with the others as well. The DC blower works fine...but that's a very simple machine. I've had calibration issues with the planer that caused me a number of extremely annoying days. And the 17" bandsaw has just never cooperated with me after many, many hours of tinkering with it and upgrading its parts. She's the next one to go. But yeah...that saw...it's been great. No problems. Of course tomorrow it'll probably explode on me for saying that, but knock on wood I'm very happy with it. I don't know if I got lucky or if they're all that way, but it seems to get fairly decent reviews, universally. I've given my opinion about the 3HP saw options before but I'll do it again, quickly. Best budget saw: G0690. Best hobby shop high-end saw: SawStop ICS3HP. Next best PCS3HP. And I just can't see a reason to buy anything but those three. Every other saw in the middle...there's a good argument against it. Jet? Save some money and buy the Grizzly. Powermatic? Might as well get the SawStop and save your hot dogs. 2 Quote
Andy Faust Posted May 27, 2017 Author Report Posted May 27, 2017 Thanks guys I'll have to look in to grisly more I've only worked on a sawlstop and a powermadic in school. But I can't see spending thousands on a saw. It's only a hobby for now and I'm just starting. So 110 is complete out of the question. Where is the best place to shop for one too I've been looking at all the normal places Amazon, wood craft, Rockler. Quote
Eric. Posted May 27, 2017 Report Posted May 27, 2017 Grizzly sells on Amazon and ebay, but the prices are all the same no matter where you buy from. Unless you have an Amazon card and you get points, you might as well just buy directly from Grizzly. The one thing Griz does pretty well is customer service. 1 Quote
Cliff Posted May 27, 2017 Report Posted May 27, 2017 9 hours ago, Eric. said: Well, let's make sure we just acknowledge once more...that I've had problems with almost every Grizzly tool I've owned...except the table saw. The only one I gave up on so far has been your jointer, but I've had a range of issues with the others as well. The DC blower works fine...but that's a very simple machine. I've had calibration issues with the planer that caused me a number of extremely annoying days. And the 17" bandsaw has just never cooperated with me after many, many hours of tinkering with it and upgrading its parts. She's the next one to go. But yeah...that saw...it's been great. No problems. Of course tomorrow it'll probably explode on me for saying that, but knock on wood I'm very happy with it. I don't know if I got lucky or if they're all that way, but it seems to get fairly decent reviews, universally. I've given my opinion about the 3HP saw options before but I'll do it again, quickly. Best budget saw: G0690. Best hobby shop high-end saw: SawStop ICS3HP. Next best PCS3HP. And I just can't see a reason to buy anything but those three. Every other saw in the middle...there's a good argument against it. Jet? Save some money and buy the Grizzly. Powermatic? Might as well get the SawStop and save your hot dogs. Yup this is exactly where I came down with my own research. That's why I am eyeing that G0690 until the SS. However, if I found a really good priced used PM or Jet, I'd buy it. But PM used - it's either the very old with no riving knife (no thanks) or a PM2000 with $20 knocked off it or some other 5HP monstrosity that I don't need. 1 Quote
Andy Faust Posted May 27, 2017 Author Report Posted May 27, 2017 It jet normally a better investment than grizzly. I don't want to buy something cheaper and be adding more money to up grade a cheep saw. I want something good in all I'd rather spend more to get that. I really have my eye on Powermatic but they're just freaking expensive. Quote
Eric. Posted May 27, 2017 Report Posted May 27, 2017 IMO Jet is comparable to Grizzly in quality. Maybe slightly better. There are certain units where this generalization doesn't hold true (that awesome drill press that Jet sells) but for the most part it's how it appears. But for the price difference it's hard to justify buying a Jet unless you can get one used for a song. You'll get people who will tell you they love their Jet saws, and I'm sure they do. But we're talking new saws at retail price, and in that context I think the Grizzly is the more logical choice. 2 Quote
knotscott Posted May 27, 2017 Report Posted May 27, 2017 Grizzly G1023RL is a great bang for the buck, and the G0690 is close, but may push your budget a bit farther. There's nothing similar in a new saw in that price range, but both will need 220v. I doubt you would need to replace either fence...both are pretty darn good in my book. The only thing to replace is the stock blade. The Jet Proshop is a good hybrid 120v option, but none of the hybrids will be as as beefy as those two Griz options. Quote
Eric. Posted May 27, 2017 Report Posted May 27, 2017 9 minutes ago, knotscott said: I doubt you would need to replace either fence...both are pretty darn good in my book. Mine made boomerangs. That's pretty bad in my book. 1 Quote
Andy Faust Posted May 28, 2017 Author Report Posted May 28, 2017 Ok what horse power should I be looking for in a saw is 1 and 3/4 to small. What a good happy medium. Quote
Ronn W Posted May 28, 2017 Report Posted May 28, 2017 Take a look at the Laguna 10" fusion saw. Also, should you ever need it, their customer support is great. https://lagunatools.com/laguna-machinery/laguna-tablesaws/fusion-36-110-volt-tablesaw/ Quote
drzaius Posted May 28, 2017 Report Posted May 28, 2017 4 hours ago, Andy Faust said: Ok what horse power should I be looking for in a saw is 1 and 3/4 to small. What a good happy medium. 1.75 will work, I had one for years, but 3HP is much nicer. There's a difference even on not terribly thick stock. Especially on woods that burn easily, like maple, It's nice to have the power to keep the feed rate up. 1 Quote
knotscott Posted May 29, 2017 Report Posted May 29, 2017 On 5/27/2017 at 5:37 PM, Eric. said: Mine made boomerangs. That's pretty bad in my book. Sounds like it was defective, and should be replaced under warranty. Quote
Tpt life Posted May 29, 2017 Report Posted May 29, 2017 I am not sure how you can see these fences as defective and not flawed in design. The UHMW faces are screwed on to the fence and create massive undulations along the length. I don't think I will replace mine any time soon. Taking the UHMW faces off or building a waxed plywood slip cover are valid options. As shipped though, many are puzzled by that design choice. I think you must be limiting your comments to the rails and locking mechanism knotscott? 1 Quote
RichardA Posted May 29, 2017 Report Posted May 29, 2017 Eric and Carus are both correct. I have the Griz 1023 rl, and couldn't be happier, 3 hp is the way to go, but you will need 220v. Quote
Just Bob Posted May 29, 2017 Report Posted May 29, 2017 Another vote for the G0690, had mine for about 8yrs, without one problem. The original fence held up for about 7yrs, and then started to wear at the contact points on the front rail. I could have just replaced those parts, but I went with the VSCT fence instead. Happy with both the fence and saw. Quote
knotscott Posted May 29, 2017 Report Posted May 29, 2017 1 hour ago, C Shaffer said: I am not sure how you can see these fences as defective and not flawed in design. The UHMW faces are screwed on to the fence and create massive undulations along the length. I don't think I will replace mine any time soon. Taking the UHMW faces off or building a waxed plywood slip cover are valid options. As shipped though, many are puzzled by that design choice. I think you must be limiting your comments to the rails and locking mechanism knotscott? If it's creating a boomerang something is wrong beyond any indulations that stray from perfectly flat. I also think most people find them flat enough, so obviously not all are effected. Quote
Eric. Posted May 29, 2017 Report Posted May 29, 2017 4 minutes ago, knotscott said: If it's creating a boomerang something is wrong beyond any indulations that stray from perfectly flat. I also think most people find them flat enough, so obviously not all are effected. When there's a dip in the middle of your fence, the board follows that dip and creates a curved cut. It's not a mystery. Those Biese clone fences aren't necessarily poorly designed, but they are poorly constructed, and in a way that often prevents you from getting a straight cut. I had to use an auxiliary fence on my saw for several years before I upgraded to an aftermarket fence. The auxiliary fence solved the problem but it's inconvenient for a number of reasons and you shouldn't have to deal with it on a new saw. I'm not stupid...I know what the problem was. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.