gee-dub Posted May 29, 2017 Report Posted May 29, 2017 On 5/27/2017 at 4:43 AM, Andy Faust said: Thanks guys I'll have to look in to grisly more I've only worked on a sawlstop and a powermadic in school. But I can't see spending thousands on a saw. It's only a hobby for now and I'm just starting. So 110 is complete out of the question. Where is the best place to shop for one too I've been looking at all the normal places Amazon, wood craft, Rockler. I think I am hearing you say that "220" volt service is out of the question(?). You will probably do better with a dedicated circuit for your saw even if used at 110volt. My old hybrid performed the same on 110v or 220v. There are still a few hybrid saws on the market targeting just the need that you have. At school you probably used 3 to 5HP cabinet saws and something like a contractor saw is gong to seem like a big step down. Hybrid somewhat bridge this gap by giving you many of the design features (although lighter weight) that cab-saws enjoy and generally operate on 110volt as well as 220volt service. The Grizzly and Jet hybrids seem to get good reports with the Laguna and Rikon falling under fire. With no recent direct experience I'll leave it to current owners to shout out their favorites as the hybrid I owned is no longer made. I wish you luck in your search; enjoy the journey. Quote
Andy Faust Posted May 29, 2017 Author Report Posted May 29, 2017 I've been using a circular saw and and edge guide. For almost a year now and it's getting annoying with how much time it takes to make a simple cut. But it sounds like I'll be pricing it to run 220 from the beaker box in to the garage. The box has the room I just don't have the skills to take that on. And sounds like I should look at grizzly. I want this to be a saw that can last me years and dosnt need extra work to make quality cuts. I've been thinking powermadic or saw stop but maybe I'll look at some cheaper brands. Quote
Mike T Posted May 29, 2017 Report Posted May 29, 2017 Maybe I'm dangerous and unwise, but unless you had to fish a wire capable of handling 220v service through a difficult spot in the wall I'm not see paying an electrician what will probably be a fair amount of $$$'s to put in a breaker run a wire and put the request receptacle on the other end. If there's a pitfall I'm not seeing shout out. 1 Quote
Vyrolan Posted May 29, 2017 Report Posted May 29, 2017 35 minutes ago, Mike T said: Maybe I'm dangerous and unwise, but unless you had to fish a wire capable of handling 220v service through a difficult spot in the wall I'm not see paying an electrician what will probably be a fair amount of $$$'s to put in a breaker run a wire and put the request receptacle on the other end. If there's a pitfall I'm not seeing shout out. This is where I come in and complain about Chicago codes. The difficulty in "just pulling some wire" can vary drastically due to local codes. Such endeavors can be nightmare for us here in Chicagoland. 2 Quote
Cliff Posted May 30, 2017 Report Posted May 30, 2017 7 hours ago, Mike T said: Maybe I'm dangerous and unwise, but unless you had to fish a wire capable of handling 220v service through a difficult spot in the wall I'm not see paying an electrician what will probably be a fair amount of $$$'s to put in a breaker run a wire and put the request receptacle on the other end. If there's a pitfall I'm not seeing shout out. I'm with you on that. In my area of IL, codes are basically useless because every house was built 115 years ago, and nobody bothers to check that anything is to code. I try to do it as close as I can myself. There have been shortcuts taken, but nothing I feel is dangerous. Quote
Mike T Posted May 30, 2017 Report Posted May 30, 2017 I'm in Oklahoma. I've seen what are called electrical updates that look absolutely terrible but I understand that other areas are very strict about allowing you to do much of anything without an act of congress. Hate to have something go wrong and your insurance won't cover it because it wasn't permitted. Quote
Guest Posted May 30, 2017 Report Posted May 30, 2017 21 hours ago, Vyrolan said: This is where I come in and complain about Chicago codes. The difficulty in "just pulling some wire" can vary drastically due to local codes. Such endeavors can be nightmare for us here in Chicagoland. Not really, you only need 2 tools. A telephone and a credit card. Quote
Vyrolan Posted May 30, 2017 Report Posted May 30, 2017 33 minutes ago, Mike. said: Not really, you only need 2 tools. A telephone and a credit card. And a firstborn for major projects or short deadlines. 1 Quote
Mark J Posted May 31, 2017 Report Posted May 31, 2017 19 hours ago, Mike. said: Not really, you only need 2 tools. A telephone and a credit card. I thought the 2 tools were cash and an envelope. ☺ 1 Quote
Andy Faust Posted May 31, 2017 Author Report Posted May 31, 2017 Hey thanks for the advice everyone. What is the difference between a traditional cabinet saw and a hybrid saw, I can'nt find a difference. Is this Just anther marketing technique. Quote
knotscott Posted May 31, 2017 Report Posted May 31, 2017 57 minutes ago, Andy Faust said: Hey thanks for the advice everyone. What is the difference between a traditional cabinet saw and a hybrid saw, I can'nt find a difference. Is this Just anther marketing technique. Hybrid saw is sort of a cross between a traditional contractor saw and an industrial cabinet saw. There are exceptions to most generalities, and the lines have blurred a bit in recent years but hybrids are typically lighter duty than industrial cabinet saws, and usually have smaller motors that will run on 120v. This is what's typically under the hood of a true industrial cabinet saw: Here's how many of the better hybrids are built: Quote
Eric. Posted May 31, 2017 Report Posted May 31, 2017 Cabinet saw has more power and it comes with a...cabinet. Hybrid often has a larger, cast iron top and higher quality fence than a contractor saw, but has less power than a cabinet saw and often has "legs" instead of the boxy cabinet. Some of the hybrids have small cabinets. The key difference is in the power. Weight and vibration are also secondary factors. Quote
gee-dub Posted May 31, 2017 Report Posted May 31, 2017 On 5/29/2017 at 10:24 AM, Mike T said: Maybe I'm dangerous and unwise, but unless you had to fish a wire capable of handling 220v service through a difficult spot in the wall I'm not see paying an electrician what will probably be a fair amount of $$$'s to put in a breaker run a wire and put the request receptacle on the other end. If there's a pitfall I'm not seeing shout out. Like changing out a starter on your pickup, what seems simple enough to some is not for others. I agree that with a bit of care running a wire from point A to point B and correctly attaching 3 wires is not something to pay for. On the other hand, I pay someone to work on my car. We all have different experiences and experience levels. 1 Quote
drzaius Posted May 31, 2017 Report Posted May 31, 2017 2 hours ago, Andy Faust said: Hey thanks for the advice everyone. What is the difference between a traditional cabinet saw and a hybrid saw, I can'nt find a difference. Is this Just anther marketing technique. I seem to recall that when hybrid saws 1st became a thing, they had the table mounted trunnions, like a contractor saw, but the motor was tucked under like a cabinet saw. They had the external appearance of a cabinet saw, but were lighter & less powerful. I can't say that I'd ever want to have another saw that had table mounted trunnions. Quote
gee-dub Posted May 31, 2017 Report Posted May 31, 2017 5 hours ago, drzaius said: I seem to recall that when hybrid saws 1st became a thing, they had the table mounted trunnions, like a contractor saw, but the motor was tucked under like a cabinet saw. They had the external appearance of a cabinet saw, but were lighter & less powerful. I can't say that I'd ever want to have another saw that had table mounted trunnions. This was true for a lot of the "also rans". The ZipCode saws had cab mounted trunnions (I thought I'd died and gone to alignment heaven) as did a couple other of the better offerings. When hybrids got such a big reaction in the marketplace there were a lot of "me too" offerings from the usual suspects that were nearly zero improvement over a contractor saw. If I hadn't had an unexpected lucrative order I would probably still be running my C-man 22124 designed by the folks who eventually brought you Steel City. Quote
JpPhysics Posted May 31, 2017 Report Posted May 31, 2017 If you can run a table saw, you can wire a 220 outlet. My advice is to check out the Electrical books at the Home Depot or Lowes, that will at least point you in the right direction. I certainly would not pay someone to do this for you unless you just don't want to do it. That being said, depending on the length of your run this could still be a pretty expensive job. Copper is not cheap these days. On a side note, I've been using my Rigid Table Saw for about 10 years now here in the Pacific Northwest. While under-powered, it cuts straight and true. The table is flat and large enough to rip a full piece of plywood if necessary. It runs on 110 and if price is an option, I wouldn't totally discredit contractor saws. (Probably not the portable ones) That being said, I am about 4 months from pulling the trigger on a Powermatic I fell in love with years ago. Learning to use the tools you have and can afford is more important than having that top of the line saw. The Rigid may not be the best saw in the world, but you couldn't tell based on the projects and furniture that I've built over the past decade. You learn the limitations and work around them. Quote
mat60 Posted May 31, 2017 Report Posted May 31, 2017 37 minutes ago, JpPhysics said: If you can run a table saw, you can wire a 220 outlet. My advice is to check out the Electrical books at the Home Depot or Lowes, that will at least point you in the right direction. I certainly would not pay someone to do this for you unless you just don't want to do it. I agree and I do the electrical stuff in my shop but if the place burns down guess who will take the blame. Quote
Andy Faust Posted May 31, 2017 Author Report Posted May 31, 2017 What powermadic is did you have. It there any job sight saws worth buying. I want to be able to build fine furniture. Or is 110 cabinet or hybrid still better than job sight. Quote
Eric. Posted May 31, 2017 Report Posted May 31, 2017 13 minutes ago, Andy Faust said: I want to be able to build fine furniture. Then get a cabinet saw. Anything less is a compromise. You don't have to spend a million dollars on a saw but you need power and precision or you'll be pulling your hair out. Buy wisely and your saw will last you the rest of your life. It's an investment in your hobby, yourself, something you're presumably passionate about. It's not a bar tab. 1 Quote
Andrew1 Posted June 1, 2017 Report Posted June 1, 2017 If you hire an eletricrian don't go for the cheapest guy find a reputable company. When i gutted my bathroom I had to laugh at some of the things they did that are not code...and dummy me forgot to confirm the wiring which of course isn't code so I have 2 lights on one switch and would need to run a new wire from the box to fix it (long story short). So at the end of the day my vote is do it yourself or don't get Mr fix it. Quote
knotscott Posted June 1, 2017 Report Posted June 1, 2017 cabinet 11 hours ago, Andy Faust said: .... It there any job sight saws worth buying. I want to be able to build fine furniture. Or is 110 cabinet or hybrid still better than job sight. The ABCs of Table Saws A cabinet saw, hybrid, or contractor saw (basically a full size stationary saw) has the lion's share of advantages over a portable. The biggest benefit of a portable saw is portability....if you don't need that feature, there's not much benefit in getting a jobsite saw over a good stationary saw. The materials of construction of a stationary saw are far more robust, the table space in front of the blade is considerably larger allowing you to get the board settled for a more accurate cut, the motors are quieter and have more torque, are more accepting of aftermarket jigs, can be more easily upgraded, are more feasible to fix in the event of a failure, have better long term reliability, and are more stable with lower vibration. Quote
Andy Faust Posted June 2, 2017 Author Report Posted June 2, 2017 Any thoughts, is this a good idea or should I save my money and try to get anther tool. I'm not sure how log I will be staying at home with my dad. I'm only 21 and will hopefully be moving out with in the year. So I'm not sure if paying an electrician would be the best idea. Quote
Andy Faust Posted June 2, 2017 Author Report Posted June 2, 2017 Hey any thoughts, is this a good investment. I currently don't have 220 and I'm still living at home as I'm only 21 and just got a full time job after graduating. I'm going to wait till I move out probably with in a year to pay an electrician. Is this a good idea in the mean time. Any one have a 1 3/4 house power powermadic. Quote
Eric. Posted June 2, 2017 Report Posted June 2, 2017 It's a nice saw but I'd rather have a 3hp Grizzly for $1500 or a 3hp SS PCS for $2900. Getting 220 is not that big of a deal. Quote
knotscott Posted June 2, 2017 Report Posted June 2, 2017 The PM1000 is a very nice saw....perhaps among the best of the 120v saws commonly available, but I still wouldn't buy it. Mainly because I don't think it represents very good value relative to some other options. The PM1000 is not like a PM2000, even though they look somewhat similar. It's a personal and subjective decision that only you can make, but my view is that it's a very expensive saw that's not equipped with the latest in in flesh sensing technology, and it's not 3hp+. With your budget you shouldn't have to give up much. 1.75hp is "adequate"....you don't necessarily need 3hp to do good work, but there is a notable difference going from 1.75hp to 3hp. I view the PM1000 similarly to a buying $50,000 Mercedes that has modest horsepower....if I'm buying a luxury car in that price range, I don't want "adequate" power...I want it to be impressive! If I'm spending in the price range of a dream saw, I want it to perform like one. I don't want to be slowing down my feed rate so I don't bog it down, and I don't ever want to outgrow it. For around that same price, you can get into a very nice Saw Stop saw that won't bite the hand that feeds it....for a bit more, you can get a pretty tricked out PCS that would be a lifetime saw of similar quality as the PM1000. For quite a bit less money, you can get a very good Jet Proshop hybrid that should have similar power to the PM1000 and all the precision you should need for ~ $800 less. For less than half the price of a PM1000, you can get into a Grizzly hybrid. As I said, it's subjective and we all have different preferences, but those are the reasons I wouldn't shell out that kind of money for that saw. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.