Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

3 down 1 to go

Featured Replies

  • Popular Post

My wife suggested I make these as gifts since she loved hers so much. These are for mom, mom in law, and sister. I just have to make one for my daughter and then I'm done. Been in the shop for about 10 hours straight........ Heavenly!

Oh...... They're candle center pieces I just haven't bought the candles yet.

post-15913-0-44552400-1418526643_thumb.j

  • Author

Thanks guys! Cement is not your friend. My legs/feet are killing me.

Awesome design. I love the legs. I'm slightly confused by the cut in the center though. It's not cut through, is it like a decorative dado or is there something in the construction that warrants it?

  • Author

wdwerker I just happen to have two pieces left and one has a thick live edge. The legs on the ones I've made are double lap joints I think is the correct term. How could I do it with the live edge. Also there's a 1 1/2" dado that raps around and with a live edge that would be tough to get square. Ideas????

Double face tape a scrap on to the bottom . That will give you an edge to ride on the fence and miter gauge to cut the joinery.

I use the powerful stuff they sell for wood turners to stick on a faceplate.

Steve's correct..  Turners tape works well for this type of stuff.

 

Cut a bit of the live edge back in the joint to get a nice flat surface and then cut the appropriate matching depth in your leg so that everything matches up.

Or face the live edges to the inside...could look cool, could look stupid.  I've seen a bench with a similar design with the live edges facing each other.  It was killer looking.

Or face the live edges to the inside...could look cool, could look stupid. I've seen a bench with a similar design with the live edges facing each other. It was killer looking.

I bet that was neat looking butt probably didn't function too well. Can't imagine putting your cheeks in a crotch

I built something kind of similar using half lap joints and a little platform for holding a Raspberry Pi for an innovation project at work. Might be fun to make a candle holder. Maybe throw in some curves. I've got some time tomorrow and a ton of square walnut leftovers from my cutting boards. 

  • Author

He's right about how the legs were made. No magic there. Finished my last one from start to finish today and now they're all clamped and glued. Tomorrow starts the finish so hopefully two can get in the mail in time for Christmas.

What are you going to be using for finish? I would go with a rubbed oil finish as it's not something that would take a lot of abuse so protection isn't a huge factor. Goes on easy, no need for buffing between coats and all that jazz. 

  • Author

T

Here is what I'm using but I still have to sand between coats don't I? YES?NO?

 

General Finishes Arm R Seal oil & urethane topcoat

I usually light sand with 600 between coats just to take off any nibs that might be there.

Did u get the plan from somewhere I could use. Looks like great last minute Xmas gifts

Sent from my iPhone using Tapatalk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.