Popular Post Mzdadoc Posted December 14, 2014 Popular Post Report Posted December 14, 2014 My wife suggested I make these as gifts since she loved hers so much. These are for mom, mom in law, and sister. I just have to make one for my daughter and then I'm done. Been in the shop for about 10 hours straight........ Heavenly! Oh...... They're candle center pieces I just haven't bought the candles yet. 3 Quote
Mzdadoc Posted December 14, 2014 Author Report Posted December 14, 2014 Thanks guys! Cement is not your friend. My legs/feet are killing me. Quote
wouldwurker Posted December 14, 2014 Report Posted December 14, 2014 Best 40 bucks you can spend. Quote
wdwerker Posted December 14, 2014 Report Posted December 14, 2014 You should make one with one live edge ! That would be an interesting contrast to the simple elegance. Quote
Tom Cancelleri Posted December 14, 2014 Report Posted December 14, 2014 Awesome design. I love the legs. I'm slightly confused by the cut in the center though. It's not cut through, is it like a decorative dado or is there something in the construction that warrants it? Quote
Mzdadoc Posted December 14, 2014 Author Report Posted December 14, 2014 wdwerker I just happen to have two pieces left and one has a thick live edge. The legs on the ones I've made are double lap joints I think is the correct term. How could I do it with the live edge. Also there's a 1 1/2" dado that raps around and with a live edge that would be tough to get square. Ideas???? Quote
wdwerker Posted December 14, 2014 Report Posted December 14, 2014 Double face tape a scrap on to the bottom . That will give you an edge to ride on the fence and miter gauge to cut the joinery. I use the powerful stuff they sell for wood turners to stick on a faceplate. Quote
..Kev Posted December 14, 2014 Report Posted December 14, 2014 Steve's correct.. Turners tape works well for this type of stuff. Cut a bit of the live edge back in the joint to get a nice flat surface and then cut the appropriate matching depth in your leg so that everything matches up. Quote
Eric. Posted December 14, 2014 Report Posted December 14, 2014 Or face the live edges to the inside...could look cool, could look stupid. I've seen a bench with a similar design with the live edges facing each other. It was killer looking. Quote
Coop Posted December 15, 2014 Report Posted December 15, 2014 Or face the live edges to the inside...could look cool, could look stupid. I've seen a bench with a similar design with the live edges facing each other. It was killer looking. I bet that was neat looking butt probably didn't function too well. Can't imagine putting your cheeks in a crotch Quote
Tom Cancelleri Posted December 15, 2014 Report Posted December 15, 2014 Zero clearance insert with a dado blade, miter gauge, miter sled. Quote
wtnhighlander Posted December 15, 2014 Report Posted December 15, 2014 I bet that was neat looking butt probably didn't function too well. Can't imagine putting your cheeks in a crotch Quote
Tom Cancelleri Posted December 15, 2014 Report Posted December 15, 2014 I built something kind of similar using half lap joints and a little platform for holding a Raspberry Pi for an innovation project at work. Might be fun to make a candle holder. Maybe throw in some curves. I've got some time tomorrow and a ton of square walnut leftovers from my cutting boards. Quote
Mzdadoc Posted December 15, 2014 Author Report Posted December 15, 2014 He's right about how the legs were made. No magic there. Finished my last one from start to finish today and now they're all clamped and glued. Tomorrow starts the finish so hopefully two can get in the mail in time for Christmas. Quote
Tom Cancelleri Posted December 15, 2014 Report Posted December 15, 2014 What are you going to be using for finish? I would go with a rubbed oil finish as it's not something that would take a lot of abuse so protection isn't a huge factor. Goes on easy, no need for buffing between coats and all that jazz. Quote
Mzdadoc Posted December 15, 2014 Author Report Posted December 15, 2014 T Here is what I'm using but I still have to sand between coats don't I? YES?NO? General Finishes Arm R Seal oil & urethane topcoat Quote
..Kev Posted December 15, 2014 Report Posted December 15, 2014 I usually light sand with 600 between coats just to take off any nibs that might be there. Quote
Dnorris1369 Posted December 15, 2014 Report Posted December 15, 2014 Did u get the plan from somewhere I could use. Looks like great last minute Xmas gifts Sent from my iPhone using Tapatalk Quote
Mzdadoc Posted December 15, 2014 Author Report Posted December 15, 2014 D It's from a back issue of Woodsmith magazine Quote
Dnorris1369 Posted December 15, 2014 Report Posted December 15, 2014 Appreciate it Sent from my iPhone using Tapatalk Quote
wdwerker Posted December 15, 2014 Report Posted December 15, 2014 So are you going to take a shot at a live edge version ? Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.