networkspeedy Posted January 1, 2015 Report Posted January 1, 2015 How big is your router table? Specifically the top? I'm trying to decide on the final dimensions for my own before I start cutting up precious material. Better too big than too small, right? Quote
Eric. Posted January 1, 2015 Report Posted January 1, 2015 Mine too, roughly. Not big enough. 1 Quote
cabinfever Posted January 1, 2015 Report Posted January 1, 2015 I want to build one into the outfeed table I'm planning. Quote
wtnhighlander Posted January 1, 2015 Report Posted January 1, 2015 Mine is a tablesaw extension wing, 27" x 22" or so. Quote
dwacker Posted January 1, 2015 Report Posted January 1, 2015 Mine is in my saw 30.5 wide. The beauty of having the table in your saw wing is with a full width out feed you have the out feed as support. If your using a bearing cutter with no fence you have the entire length of the saw as out feed support for the router. You start with your piece resting on the saw out feed as you make the cut you walk the long piece around the cutter and feed it onto the length of your saw. 1 Quote
Beechwood Chip Posted January 1, 2015 Report Posted January 1, 2015 Better too big than too small, right? If you have infinite shop space. Quote
wdwerker Posted January 1, 2015 Report Posted January 1, 2015 My biggest one is 72 x 30 with a power feeder . I mainly use it to groove panels for a 1/4" cabinet back or drawer sides for bottoms. It's also good to route moldings on a wide long plank then I rip off the piece and run it again. A PC 690 router usually survives 4 or 5 years before the brushes or bearings give up. I just swap to a new motor. I hooked a shop vac to a 5 gallon bucket that covers the entire router, works pretty dam good ! Quote
blakjak220 Posted January 1, 2015 Report Posted January 1, 2015 Mine's 27 X 43 - But it's the Incra and so the fence is parallel to the 27" side so the fence can slide back and forth along the 43" length. Wouldn't be a very good size if you had a conventional fence that didn't need all that room in the back. Quote
Vyrolan Posted January 1, 2015 Report Posted January 1, 2015 Mine too, roughly. Not big enough. Eric, you have the Incra setup right? So the fence is on the shorter edge to support the positioner...how do you like that setup? I love the idea of the Incra but I also see myself using a table mostly for shaper-like things and so a much wider table would be nicer. Quote
Eric. Posted January 1, 2015 Report Posted January 1, 2015 I love it, but I still find myself wishing the table was bigger to support longer pieces. No other complaints. You can mount the Incra fence on as big of a table as you want...I just didn't have enough space to go any bigger. Quote
BuilderBill Posted January 2, 2015 Report Posted January 2, 2015 http://patwarner.com/router_table.html Quote
Coop Posted January 2, 2015 Report Posted January 2, 2015 38x 24 x 36, no, that's wishful thinking, mine is an extension of my ts and is 25"x 27" Quote
networkspeedy Posted January 2, 2015 Author Report Posted January 2, 2015 http://patwarner.com/router_table.html That's one amazing table to be sure. The custom rip fence is a work of pure genius Quote
Brendon_t Posted January 2, 2015 Report Posted January 2, 2015 Not nearly big enough. I have a craftsman aluminum table measuring 14"x 23". Quote
networkspeedy Posted January 2, 2015 Author Report Posted January 2, 2015 this ended up being a really fun learning experience. Who knew that there would be so many replies? That's lots of fun. Thanks everyone for your response. It has helped me decide the size that I will use for my own table Quote
networkspeedy Posted January 2, 2015 Author Report Posted January 2, 2015 38x 24 x 36, no, that's wishful thinking, mine is an extension of my ts and is 25"x 27" Why 38 inches instead of the more common 36? Quote
Cochese Posted January 2, 2015 Report Posted January 2, 2015 K probably likes his a bit more top heavy. Quote
Woodenskye Posted January 3, 2015 Report Posted January 3, 2015 Extension wing in table saw, 16" x 27". Old stand alone was 24" x 32". Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.