Andy Wright Posted September 6, 2015 Report Posted September 6, 2015 I built this coffee table completely out of reclaimed oak. The top of the table is built using 1.25" thick butcher block planks that came out of salvaged semi-trailers. I'm not sure of the age, but they were filthy when I bough them and have tons of character. The legs and apron came from beams out of an old barn.One of the biggest challenges for me was striking the right balance between highlighting the "character" of the salvaged wood and showing craftsmanship in the final piece of furniture. I left the top rough and did not plug the holes, but I did plane the planks down to get them flat and to a consistent thickness. 2 Quote
..Kev Posted September 6, 2015 Report Posted September 6, 2015 Very cool Andy! Goes well in that room! Make sure you sign it! Quote
Chet Posted September 6, 2015 Report Posted September 6, 2015 Thats real nice. The oak from the semi's is that the stuff that Rockler was selling a year or so ago? Quote
Andy Wright Posted September 6, 2015 Author Report Posted September 6, 2015 I bought the semitrailer wood from a guy in Oklahoma who had it stacked to the ceiling in his garage. Quote
estesbubba Posted September 6, 2015 Report Posted September 6, 2015 That table has a lot of character! Good job. Quote
wtnhighlander Posted September 6, 2015 Report Posted September 6, 2015 Nice, Andy! You did great balancing the character with craftsmanship. Quote
Larry Moore Posted September 6, 2015 Report Posted September 6, 2015 Nice mix of character and craftsmanship Quote
N00b-in-training Posted September 6, 2015 Report Posted September 6, 2015 Very cool Andy! Excellent work Quote
mat60 Posted September 6, 2015 Report Posted September 6, 2015 Nice Job....I bet it will last forever Quote
Andy Wright Posted September 6, 2015 Author Report Posted September 6, 2015 Thank you for the kind comments. When I took the pictures in our house I didn't have the best lighting and didn't get to show any of the details on the base of the table. Here is a pic of the base taken while i was finishing the table in the shop. The apron is mortise and tenon, with a bead detail. The legs are solid oak with a taper on the inside faces. I left the original saw marks on the wood wherever possible. Quote
mat60 Posted September 6, 2015 Report Posted September 6, 2015 I Like the beed detail and I think 8 people could sit on it that table and it would still be fine..Very nice. Quote
Rapid Roger Posted September 6, 2015 Report Posted September 6, 2015 I just hope that the finish doesn't get scratched form use! Nice job buy the way. Rog Quote
prov163 Posted September 7, 2015 Report Posted September 7, 2015 Dumb question Andy, but as old and stable as this oak must be, why did you put the cleats underneath? I'm getting ready to build a sofa table out of some old reclaimed material so the answer will be helpful n my build. Thanks! Quote
Guido_de Posted September 7, 2015 Report Posted September 7, 2015 It is still wood and as such it will continue to absorb/ dissipate moisture and thus move. Modern houses pose a reduced risk as the humidity in the air is less prone to change over the season. However, in my apparent (brick house, 120 years old, no AC) there is still quite a change in humidity. If anything: a clear is always good, safe practice Quote
Andy Wright Posted September 7, 2015 Author Report Posted September 7, 2015 Dumb question Andy, but as old and stable as this oak must be, why did you put the cleats underneath? I'm getting ready to build a sofa table out of some old reclaimed material so the answer will be helpful n my build. Thanks! The pieces for the top were not perfectly flat, but I didn't want to go crazy with removing wood to flatten them out because then I would end taking the imperfections out of the high spots in the table top. I also don't have a great way to flatten a board that is 12"x52" in my shop.Since the pieces didn't line up perfectly for a glue up, I left the top as four separate wooden planks that are not glued together (top is 40" so they are each 11" inches wide with a 1/2" half lap on each end). The cleats hold the top together and they also hold the top flat (each plank was within 1/16" of an inch so I don't think it will pose any long term problems). I used slightly elongated screw holes to allow for some wood movement. Quote
mat60 Posted September 7, 2015 Report Posted September 7, 2015 Cool...I was hoping the cleats were not glued.... Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.