Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

hybrid table saw decision: Delta vs Ridgid

Featured Replies

Well I am going to upgrade my 20 yo delta contractor table saw.  It works fine but the fence sucks.   I looked into installing an aftermarket fence but determined the table has no "meat" to drill holes into to, to attach the Vega fence.  (which I decided I was going to buy).   So time to upgrade everything.  

I narrowed it down to the Delta 36-725 and the Rigid R4513. I have read lots of reviews and I am still cant nail it down.    The Rigid might have the trunnon issue and the rail might bend because it is aluminum.  The Delta might not have parts in the future but has a great rail system (which is what makes a table saws great).  So,  I am leaning towards the Delta, but would love to hear ya'lls opinion.

Awhile back i was looking at these saws. I had a different feeling about the rail system. It has a split fence rail which i wouldnt call a bonus. Unless youre referring to something else.

.

Have you considered the Grizzly hybrid?

Sent from my SAMSUNG-SM-G890A using Tapatalk

I actually bought the Delta 36-725 from Lowes... and then returned it after a very frustrating weekend trying to tune it up.  Reviews are really good though, so I may have simply gotten a bad unit. Not sure, but it put me off enough to not want to try putting another one together.

Initial impressions of the saw out of the box were great - flat cast iron table, quiet operation, etc.  Problems began when I started putting it together (which was another issue - assembly instructions left much to be desired).  Issues I ran into:

  • The split rail was a pain in my rear, never could get them aligned - one of the rails seemed slightly twisted or something.  
  • The fence would also pick up about 1/8" on the left side only when I locked it down, so the fence was inconsistent 
  • Fence also wouldn't clamp down consistently parallel to miter slots after setting up. I would clamp down then tune it up, then move slightly and clamp it down again and it would be off
  • Back of fence also dragged on the table, no matter how high I adjusted it off table. I even added a bunch of washers to the rear fence clip - this kind of worked, but not ideal.

Like I said, reviews are good, so seems like most really like the saw. I agree with sheperd80 above that a Grizzly might be the way to go. Personally, I saved a while and blew my entire tool budget on a sawstop - don't regret it at all even though it was way more than I was originally planning to spend.

Good luck!

I bought the ridgid and have been pretty happy with it. The fence has been fine for me, came tuned up nicely. Sure there are nicer saws out there, but nothing comparable in the sub $600 range, IMO. If you're willing to spend 50% more, a lot of people do like the grizzly, but for me I figured the ridgid would work fine for at least the next few years, and if I'm continuing to do more and more woodworking I can upgrade down the road to a cabinet saw. YMMV

I've been using the Ridgid for several years with no complaints. To be honest, I've thought about upgrading but couldn't justify it as the saw works as it should. I spent money in other areas in my shop. 

  • Author
8 hours ago, sheperd80 said:

Awhile back i was looking at these saws. I had a different feeling about the rail system. It has a split fence rail which i wouldnt call a bonus. Unless youre referring to something else.

.

Have you considered the Grizzly hybrid?

Sent from my SAMSUNG-SM-G890A using Tapatalk

I fiquared it is close to  the Beisemeyer rail system so more options in the future.   

Looking at the Grizzly, is the 715 worth stepping up in price compared to the 755?  What are the differences between the 2?

8 hours ago, sheperd80 said:

Awhile back i was looking at these saws. I had a different feeling about the rail system. It has a split fence rail which i wouldnt call a bonus. Unless youre referring to something else.

.

Have you considered the Grizzly hybrid?

Sent from my SAMSUNG-SM-G890A using Tapatalk

What is the split rail consist of?  The rail being in the front and back or the front main rail comes in two pieces?

 

How does this rail compare to the rigid rail system?

7 hours ago, cjtboy said:

I actually bought the Delta 36-725 from Lowes... and then returned it after a very frustrating weekend trying to tune it up.  Reviews are really good though, so I may have simply gotten a bad unit. Not sure, but it put me off enough to not want to try putting another one together.

Initial impressions of the saw out of the box were great - flat cast iron table, quiet operation, etc.  Problems began when I started putting it together (which was another issue - assembly instructions left much to be desired).  Issues I ran into:

  • The split rail was a pain in my rear, never could get them aligned - one of the rails seemed slightly twisted or something.  
  • The fence would also pick up about 1/8" on the left side only when I locked it down, so the fence was inconsistent 
  • Fence also wouldn't clamp down consistently parallel to miter slots after setting up. I would clamp down then tune it up, then move slightly and clamp it down again and it would be off
  • Back of fence also dragged on the table, no matter how high I adjusted it off table. I even added a bunch of washers to the rear fence clip - this kind of worked, but not ideal.

Like I said, reviews are good, so seems like most really like the saw. I agree with sheperd80 above that a Grizzly might be the way to go. Personally, I saved a while and blew my entire tool budget on a sawstop - don't regret it at all even though it was way more than I was originally planning to spend.

Good luck!

Thanks for the input.   That is why I am having a hard time deciding.  I hear really good things about both the Delta and Rigid.   Then there are a few from each that have problems.   Which to choose?   Or are they both equally the best in the price range and I have to accept for this price range there will be some minor flaws just as any high volume mass produced product would have.

6 hours ago, JosephThomas said:

I bought the ridgid and have been pretty happy with it. The fence has been fine for me, came tuned up nicely. Sure there are nicer saws out there, but nothing comparable in the sub $600 range, IMO. If you're willing to spend 50% more, a lot of people do like the grizzly, but for me I figured the ridgid would work fine for at least the next few years, and if I'm continuing to do more and more woodworking I can upgrade down the road to a cabinet saw. YMMV

I think I am in the same boat as you.  Staying in the $600 range would do fine for me and if I really need it I can upgrade to a cabinet saw in the far furture.    Really,  I am happy with the contractor saw I have now, it is just the fence sucks and I need straighter cuts..

  • Author
6 hours ago, JosephThomas said:

I bought the ridgid and have been pretty happy with it. The fence has been fine for me, came tuned up nicely. Sure there are nicer saws out there, but nothing comparable in the sub $600 range, IMO. If you're willing to spend 50% more, a lot of people do like the grizzly, but for me I figured the ridgid would work fine for at least the next few years, and if I'm continuing to do more and more woodworking I can upgrade down the road to a cabinet saw. YMMV

Is the rigid a split rail fence system similar to the delta?  Similar more on the back side.   I know the front rail are different between the two.

Yes it's a split rail. I was a little stressed out trying to set it up the first time, but once it was done I haven't had to worry about it again

Sent from my Nexus 5 using Tapatalk

Both of those saws has a split front rail, but the Delta has the better fence overall IMO.  The Ridgid is an all aluminum dual locking system with a split front rail, that's sort of a spinoff of previous Ridgid fences, but isn't quite as stiff as the older ones. The Delta is a steel t-square front locking system with aluminum faces on the steel fence tube....the front rail is split also, but I do prefer the welded steel t-square design.  The Delta hasn't been out as long, but seems to have a better track record overall...any issues I've heard of have been minor isolated random concerns.  The R4512 had a systemic alignment issue...the alignment would shift out of acceptable limits when the blade height was changed. It didn't effect all units, but quite a few popped over a fairly long period of time....they've supposedly fixed it.  Parts issues with Delta are purely speculation AFAIK....other than aftermarket accessories like dado inserts not being available when the 36-725 first came out, I haven't read about lack of any parts. (It's common for newly released saws to not have accessories available for a few months.)

All new saws for < $600 are going to have some compromises....steel wings, lesser fences, smaller motors, table mounted trunnions, open stands, etc.  The key is to pick which of those are easiest for you to live with.  The Cman 21833 is nearly the same saw as the R4512, and is worthy of some consideration if you find yourself leaning toward the Ridgid. The 21833 has a 15 amp motor vs 13 amp on the other two.  Of those 3, I still like the Delta better, based on the fence, but you may feel differently.  

Used is always worth a look to see if there are any cream puff deals in your area.  $300-$400 can buy a lot of used saw. $500+, even more saw. The Grizzly G0771 and G0715P are a step up, cost more, and are worth some thought if you can handle the price increase - what you gain with the G0771 is a full enclosure, cabinet mounted trunnions, and solid cast iron wings...the fence is somwhat similar to the R4512 and 21833...it's functional but not great.  The G0715P has very similar underpinnings as the R4512 and 21833....and also had very similar issues with earlier units.  The G0715P offers a better fence, along with solid wings, and full enclosure.  Grizzly is a direct importer...there are savings to be had, but you have to be your own middleman in the event of any issues.  

The end performance of any of them will be very dependent on proper setup and blade selection, but all have potential be good solid performers..

 

 

I've been using the Ridgid for several years with no complaints. To be honest, I've thought about upgrading but couldn't justify it as the saw works as it should. I spent money in other areas in my shop. 

I'm in the same boat. Have had mine for a few years and it's been great. I'm always looking for an excuse to upgrade a tool but haven't found a reason to upgrade my R4512 yet. I set the fence once when I got it and it's dead on years later.

  • Author
27 minutes ago, knotscott said:

Both of those saws has a split front rail, but the Delta has the better fence overall IMO.  The Ridgid is an all aluminum dual locking system with a split front rail, that's sort of a spinoff of previous Ridgid fences, but isn't quite as stiff as the older ones. The Delta is a steel t-square front locking system with aluminum faces on the steel fence tube....the front rail is split also, but I do prefer the welded steel t-square design.  The Delta hasn't been out as long, but seems to have a better track record overall...any issues I've heard of have been minor isolated random concerns.  The R4512 had a systemic alignment issue...the alignment would shift out of acceptable limits when the blade height was changed. It didn't effect all units, but quite a few popped over a fairly long period of time....they've supposedly fixed it.  Parts issues with Delta are purely speculation AFAIK....other than aftermarket accessories like dado inserts not being available when the 36-725 first came out, I haven't read about lack of any parts. (It's common for newly released saws to not have accessories available for a few months.)

All new saws for < $600 are going to have some compromises....steel wings, lesser fences, smaller motors, table mounted trunnions, open stands, etc.  The key is to pick which of those are easiest for you to live with.  The Cman 21833 is nearly the same saw as the R4512, and is worthy of some consideration if you find yourself leaning toward the Ridgid. The 21833 has a 15 amp motor vs 13 amp on the other two.  Of those 3, I still like the Delta better, based on the fence, but you may feel differently.  

Used is always worth a look to see if there are any cream puff deals in your area.  $300-$400 can buy a lot of used saw. $500+, even more saw. The Grizzly G0771 and G0715P are a step up, cost more, and are worth some thought if you can handle the price increase - what you gain with the G0771 is a full enclosure, cabinet mounted trunnions, and solid cast iron wings...the fence is somwhat similar to the R4512 and 21833...it's functional but not great.  The G0715P has very similar underpinnings as the R4512 and 21833....and also had very similar issues with earlier units.  The G0715P offers a better fence, along with solid wings, and full enclosure.  Grizzly is a direct importer...there are savings to be had, but you have to be your own middleman in the event of any issues.  

The end performance of any of them will be very dependent on proper setup and blade selection, but all have potential be good solid performers..

 

 

Thank you for the great write up.   Everything you said is what is drawing me to the delta.   I plan to make my own insert so no need to buy theirs.  I plan to add a wing router table so I dont care about the cast iron. Do care about the enclosure.  I wanted to buy used and have look for a long time but Atlanta craigslist is slim pickings.  And I have waited long enough. I was happy with the  small motor on my contractor saw so this would be an upgrade.   Really my biggest want is a decent fence.   And it sounds like the delta is a tad better.  

I just needed someone to give me a good argument to make me feel good about going to Delta and your write up was very balance but had all the points I had concerns about and answered those concerns.

Thank you for time and input.

 

3 hours ago, Dennis Machida said:

I plan to make my own insert so no need to buy theirs. 

 

Hi Dennis-

Worth noting making inserts for this is certainly doable, but they make it kind of a pain as there is such a narrow lip to hold them in place. You either have to make insert super thin or rout a thin lip around the insert, etc.  Either way, certainly not a deal breaker or anything. There are YT videos out there on people doing this - worth watching them for tips/tricks on this.

Also - definitely worth checking out the assembly videos on YT too - much easier to follow vs. the manual (unless they've improved this). 

I've also attached a powerpoint doc from Delta (hope the attachment works) - it outlines how to align the blade to the miter slot. Not sure why this isn't in manual, but at least this makes it clear. 

Sounds like you're going with the Delta, let us know how you like it!

Delta Contractors Saw 36-725 Blade Alignment.pptx

  • Author

I was going to go the router route for inserts.  

Thanks for the power point slides.  Ill check it out.

I've seen and  bookmarked the YT vids.  Ill Definatly refer to them.

Now my problem is 6 Lowes around me are out of stock of the delta.  Are they phasing this module out?

 

9 minutes ago, Dennis Machida said:

I was going to go the router route for inserts.  

Thanks for the power point slides.  Ill check it out.

I've seen and  bookmarked the YT vids.  Ill Definatly refer to them.

Now my problem is 6 Lowes around me are out of stock of the delta.  Are they phasing this module out?

 

I don't think that it's very old there may just be a gap between shipments and demand was high enough. I know they have one in the store here you may be able to order it through lows and have it shipped to your nearest store.

Last month I was in the market for a new table saw and had it narrowed down to the delta and the rigid as well. I ultimately went with the delta because I liked the fence system, I also didn't want to have to deal with the trunk or issue if the saw had it. I am happy with my purchase and have no regrets. Setting up the saw takes a while, so be prepared for a headache while setting it up. 

During the set up I did go back to a YouTube video to aid in setting it up. 

I bought the 36-725 last May I think. Pretty happy with it overall. Dust collection is meh. Like even with the zci it shoots a ton out the top. But everything that falls downward gets picked up by the shop vac. My steel wings suck. They have bent or something. The right one slopes down. I don't think it's the rails, because I feel like the fence would be sticking or something if they were bent or not level with the cast iron top. The fence is pretty good, but I'm still thinking of a VCST one because of the variances in the flatness across the entire length. I'm not sure if that is just me wanting new stuff or what. 

Ultimately, I think it's a great saw for the money. I have stalled it cutting through 2 1/8" walnut and 2 inch oak. I was running it through too fast I think. I plan to upgrade it as well. Replace the two steel wings with sawstop cast iron ones, new fence (either VCST or swap in the incra fence system. 

Just a matter of whether or not I want to spend that money when I could get a Sawstop after saving for a bit.

  • Author

UPDATE:  Good and bad news

I went to lowes today and picked up the delta.  I even got 15% off regular price.

Spent 4 hours assembling the saw.  That's all the good news.

Now the bad. Went to turn on the saw the motor buzzed. And the blade shuttered but would not turn.  I thought possible not getting enough amps because it was plugged into an extention cord.  So I plugged it directly I to the wall. The blade started to slowly spring then after 2 seconds stopped.  Now no sounds from the motor.  

I'm afraid I got a bad motor. any suggestions?

The start capacitor should be in a large bump on the motor housing.  There may be two of them, start and run capacitors or just a start.  You can generally wire the motor for 110 or 220 volts.  It would be worth taking a look inside the box on the motor to make sure it's wired correctly.  If it's wired for 220 and you are giving it 110 it's not going to be happy.

 

  • Author
  • Popular Post

SUCCESS.

Thanks to everyone who pointed me to the capacitors. 

I woke up this morning very frustrated that my new saw wasn't working.  Had breakfast and then went down stairs to the shop.

  At first I was trying to figure out where the wiring spot was where I could look to see if my table was wired for 220 instead of 110 like the power cord said.  So I got under the table and pulled the bottom cover off.  Two screws not too bad.  Bam!  I see the 2 caps and a disconnected black wire.  One of the starting motor caps had become disconnected.  I popped it back on.  Plugged her in and we had constant blade turn.   I finished by calibrating the ruler and made two cuts.  She is true and straight.  Ready to build cabinets.

Thanks to everyone who commented and gave suggestions.  

Congrats on the new saw. Hope that's your only trouble.

Sent from my VS986 using Tapatalk

Any time I have the cover off of wiring I take a picture, then check that all the connections are tight before closing it up.  Then if anything comes loose from vibration I have a reference.

Wouldn't it be great if the directions included close up color pictures with labels ? Especially for things like changing from 120v to 240v motor wiring.

3 hours ago, wdwerker said:

Any time I have the cover off of wiring I take a picture, then check that all the connections are tight before closing it up.  Then if anything comes loose from vibration I have a reference.

Wouldn't it be great if the directions included close up color pictures with labels ? Especially for things like changing from 120v to 240v motor wiring.

That saw does have directions for the conversion but I can't remember if it's something you have to download or not. Overall, the book is not great. I think this is a place a lot of companies cut costs. 

Glad you got the saw working @Dennis Machida

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.