Rex Edgar Posted September 1, 2016 Report Posted September 1, 2016 I ordered two bits from Woodcraft a week or so back. They were 3 1/4" and 3 1/8" in diameter. There is a special project that they are needed for. The holes are too small a diameter for the router with the circle jig. The bits are Wood River brand and the low price should have scared me off, ($ 31.00-$33.00). I chucked up the larger and using the slowest speed, I test drilled a piece of knotty pine. Got nowhere fast. I tried a milled scrap of cherry and the same result. Woodcraft was good about sending a return label to send the bits back,(I only tried one). Anyhow the point of this post is to see if anyone has used Forstner bits this large and where did they get them. I figure that I'll end up paying much more than $30 something for them. I started with the lowest speed (210) and tried bumping the speed twice with no good results. I have a set of Austrian made bits that go from 1/4"-2 1/8" and the largest bit made small work out of the larger hole I was trying to drill. Any help is always appreciated...... Quote
Eric. Posted September 1, 2016 Report Posted September 1, 2016 I have a few of the Lee Valley bits, they're decent. I'd like the whole set but I don't have an extra $400 laying around. http://www.leevalley.com/US/wood/page.aspx?p=63566&cat=1,180,42240,63566 1 Quote
Chestnut Posted September 1, 2016 Report Posted September 1, 2016 I have a CMT bit that i abuse and it cuts really slowly and poorly. I just got a new set of Freud bits and they cut wonderfully. So wonderfully in fact i was assuming they were the old CMT bit and i drilled WAY to far the first time i used it. I put them down for Christmas and birthday gifts. A lot of people think this stuff makes lame gifts but I'd get more excited seeing a drill bit then most anything else. I also tried to push people to give me vintage hand planes but they seem to be afraid of buying them even though I'd probably not even use them. Quote
Immortan D Posted September 1, 2016 Report Posted September 1, 2016 My biggest fortsner bit is 2". Beyond that, I use hole saws. Quote
Rex Edgar Posted September 1, 2016 Author Report Posted September 1, 2016 Just now, Immortan D said: My biggest fortsner bit is 2". Beyond that, I use hole saws. Thanks, I need a flat bottom hole, which a hole saw can't do. 9 minutes ago, Eric. said: I have a few of the Lee Valley bits, they're decent. I'd like the whole set but I don't have an extra $400 laying around. http://www.leevalley.com/US/wood/page.aspx?p=63566&cat=1,180,42240,63566 Thanks. Eric. Ordered. Quote
gee-dub Posted September 1, 2016 Report Posted September 1, 2016 First I should say that I ran a Woodcraft set of Chinese bits for many years without issue. I did become very proficient at sharpening them but, they were fine one touched up. The largest Lee Valley I have is a 2-3/16" but, it cuts like a champ. Their 3-1/8" is only $45. If you are going to do a lot of this I would look at Amana, Fisch, Bormax or even Freud as possibilities. I am not one of those folks who think a router can do anything but, one of these to make a template and a template bit in a router would do the trick in a lot of cases. 1 Quote
Tom Cancelleri Posted September 1, 2016 Report Posted September 1, 2016 I used a large woodriver 2 7/8" (i think) forstner bit for the acetal bushing on my Roubo leg vise I had no issues. Quote
wtnhighlander Posted September 1, 2016 Report Posted September 1, 2016 You might cut the rim of the hole with a hole saw, then hog out the waste with a router, free hand, to get a flat bottomed "well". Quote
Rex Edgar Posted September 1, 2016 Author Report Posted September 1, 2016 14 minutes ago, wtnhighlander said: You might cut the rim of the hole with a hole saw, then hog out the waste with a router, free hand, to get a flat bottomed "well". What I'm attempting is mounting a small (3 1/4" dia.) plate in a decorative piece of wood. I've come up with drilling a small reference hole for a center point, then drilling the rear of the wood just short of a through hole, then turning the piece over and using the center point, drilling a 3 1/8" hole so there's a lip to retain the plate. The bits need to be sharp so as to cut the fibers, not rip or power through them. I'll post pics if successful..... Quote
wdwerker Posted September 2, 2016 Report Posted September 2, 2016 Do you realize that your lip will only be 1/16 th on each side? Anything less than perfect alignment will result in no lip somewhere and an 1/8th lip opposite it. I would use a 3" bit for the face side which would give you a 1/8th lip. Use your drill press. Make sure the table is perfectly square to the bit. Line up the parts carefully and clamp them down before drilling. Use the lowest speed possible and feed the bit slowly. I have a 3" Fisch bit that I bought for a job many years ago. It cuts well but it was quite pricey. Use the smallest bit possible to drill through so you can align the holes from both sides. Practicing on scrap is strongly encouraged ! 1 Quote
drzaius Posted September 2, 2016 Report Posted September 2, 2016 I have that big Lee Valley set & they are very good. It seems like most forstner bits are carbon steel, which are ruined at the first hint of overheating. These are HSS & take the heat quite well. I assume you're using these in a drill press? They need lots of feed pressure to cut well. 1 Quote
andrew-in-austin Posted September 2, 2016 Report Posted September 2, 2016 Here is the very best of the best: https://www.timbertools.com/ZOBO-System-3-Carbide-drill-bits-Imperial.html Prepare for heart attack when you see the price... For the router approach: Instead of a circle jig, about about a router template and the guide bushing? Or you can make a circle jutting jig that goes down to really small diameters: http://www.patwarner.com/router_circle_maker.html 1 Quote
pkinneb Posted September 2, 2016 Report Posted September 2, 2016 3 hours ago, andrew-in-austin said: Prepare for heart attack when you see the price... whoa I guess Quote
Rex Edgar Posted September 2, 2016 Author Report Posted September 2, 2016 17 hours ago, wdwerker said: Do you realize that your lip will only be 1/16 th on each side? Anything less than perfect alignment will result in no lip somewhere and an 1/8th lip opposite it. I would use a 3" bit for the face side which would give you a 1/8th lip. Use your drill press. Make sure the table is perfectly square to the bit. Line up the parts carefully and clamp them down before drilling. Use the lowest speed possible and feed the bit slowly. I have a 3" Fisch bit that I bought for a job many years ago. It cuts well but it was quite pricey. Use the smallest bit possible to drill through so you can align the holes from both sides. Practicing on scrap is strongly encouraged ! 3 1/4"- 3 1/8" mmmmm, precision is a must, math was not my best subject. I plan to try a few tests on scrap. 3" bit may be added to the collection. Thanks for the replies and links, I like the small circle jig and it's price is not outta sight. Wdwerker, if I clamp the piece in the drill press and stop just short of through, then change to the smaller bit and make the through cut, haven't I eliminated one possible error source? Quote
wdwerker Posted September 2, 2016 Report Posted September 2, 2016 Practice on scrap of the same thickness. Set the depth stop on your drill press. Make sure the wood is clamped down. The tiny pilot bit will help you re-align to drill the smaller through hole. 1 Quote
Rex Edgar Posted September 7, 2016 Author Report Posted September 7, 2016 On September 2, 2016 at 5:18 PM, wdwerker said: Practice on scrap of the same thickness. Set the depth stop on your drill press. Make sure the wood is clamped down. The tiny pilot bit will help you re-align to drill the smaller through hole. Well, success! In a piece of scrap anyway. I ordered the Woodpeckers Drill Press Table a few weeks ago and what a difference there is to that and 'freehand' drilling. Wdwerker and Eric a shout out, the Lee VAlley drill bits cut like nobody's bidness and to Wdwerker, I never flipped the scrap piece of ply. I set the drill stop to just before exit and then finished with the smaller bit. All parts clamped down, of course. 2 Quote
gee-dub Posted September 7, 2016 Report Posted September 7, 2016 Awesome. High five for everybody ;-) Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.