Recommended Posts

Posted

I've got a Griz cabinet saw, 0715, has anyone thought of replacing the plastic slides on their fence with aluminum extrusions?  I found these on amazon and was thinking this might make a nice replacement as the plastic on my fence is not completely straight. 

https://www.amazon.com/80-20-Inc-T-Slotted-Extrusion/dp/B001F0K4IW/ref=sr_1_48?ie=UTF8&qid=1478544844&sr=8-48&keywords=aluminum+t+slot+extrusion

http://www.grizzly.com/products/10-Hybrid-Table-Saw-with-Riving-Knife-Polar-Bear-Series/G0715P

Posted

I was thinking it would require countersunk screws through the extruded fence.  Either drill to match existing holes or make new holes in the fence.  I can't remember how the fence is constructed, I think it is just a tube, but you could also drill access holes in the bottom of it if needed. 

Posted

IF I were to replace an extrusion,  I would try Allan at ask woodman. knowing it is for a saw,  he should ship you a dead straight one.  15 or 20 thousands wouldn't matter to most people.  it will if it's your fence.

Posted
4 hours ago, xxdabroxx said:

I've got a Griz cabinet saw, 0715, has anyone thought of replacing the plastic slides on their fence with aluminum extrusions?  I found these on amazon and was thinking this might make a nice replacement as the plastic on my fence is not completely straight. 

https://www.amazon.com/80-20-Inc-T-Slotted-Extrusion/dp/B001F0K4IW/ref=sr_1_48?ie=UTF8&qid=1478544844&sr=8-48&keywords=aluminum+t+slot+extrusion

http://www.grizzly.com/products/10-Hybrid-Table-Saw-with-Riving-Knife-Polar-Bear-Series/G0715P

Yes I have thought about it, go for it, if it works I will copy you:D.

Posted
33 minutes ago, ben_r_ said:

Maybe Im confused, but how would you access the screws to tighten the extrusion on to the steel middle part of the fence?

The steel is square tube. Over drill the far wall. Stick an Allen key bolt or other arrangement through the overdrill. 

  • Like 1
Posted

If you are planning to bolt an extrusion to the side of a tubular steel fence core, beware that you can actually warp the extrusion to match any variation of the fence surface. I would consider using shims/washers, and a minimum number of bolts, to limit contact between the aluminum and the steel.

  • Like 2
Posted
6 minutes ago, wtnhighlander said:

If you are planning to bolt an extrusion to the side of a tubular steel fence core, beware that you can actually warp the extrusion to match any variation of the fence surface. I would consider using shims/washers, and a minimum number of bolts, to limit contact between the aluminum and the steel.

I was thinking I could use aluminum foil as shim stock if needed.  I'm assuming that is why the plastic is not flat now.  That being said I could also try and shim the plastic, but if I'm taking it apart might as well upgrade right?  Seems like the track could be useful for holding blocks, jigs, and whatnot. 

Posted

A structural engineers thoughts here, so take these with a grain of salt, I may be over thinking it.

If you cut thin or softer materials, won't those ridges cause irregularities as the fence potentially digs into your wood? I'd think you'd want at least the bottom inch to be a flat smooth surface, though above that, I can potentially see where a T-Track would be beneficial. 

You might be able to sand those ridges off, but you'd be better off just finding an extrusion with a smooth surface on both sides to begin with. 

If you've got un-coated aluminum against un-coated steel/iron you'll get galvanic corrosion in the aluminum. As the aluminum corrodes, it will expand, potentially moving itself out of flat. A plastic washer layer as discussed above would stop this, though I'm not sure how it would effect your precision.

Also steel and aluminum expand and contract at different rates so if your saw is in an environment with an unstable temperature, you could see the some small amount of warping as one tries to move more than the other that it is rigidly fixed too. 

Posted
14 hours ago, Isaac Gaetz said:

If you've got un-coated aluminum against un-coated steel/iron you'll get galvanic corrosion in the aluminum.

You need to add moisture to the equation to get galvanic corrosion. So that would depend on where you live. Wouldn't be a problem where I am.

Posted
5 minutes ago, drzaius said:

You need to add moisture to the equation to get galvanic corrosion. So that would depend on where you live. Wouldn't be a problem where I am.

Yeah many factors contribute. A lot of users seem to have garage shops, some in pretty humid areas. In general, aluminum directly fastened to steel isn't a good idea when avoidable. The thing about corrosion is it is expansive, which can add prying action and pressure, which could distort your extruded fence. Mind you I'm not talking about it turning into some ridiculous shape, just a thousand of an inch here or there, but with fences, obviously woodworkers care about that sort of precision.  

Posted
15 hours ago, Isaac Gaetz said:

A structural engineers thoughts here, so take these with a grain of salt, I may be over thinking it.

If you cut thin or softer materials, won't those ridges cause irregularities as the fence potentially digs into your wood? I'd think you'd want at least the bottom inch to be a flat smooth surface, though above that, I can potentially see where a T-Track would be beneficial. 

You might be able to sand those ridges off, but you'd be better off just finding an extrusion with a smooth surface on both sides to begin with. 

If you've got un-coated aluminum against un-coated steel/iron you'll get galvanic corrosion in the aluminum. As the aluminum corrodes, it will expand, potentially moving itself out of flat. A plastic washer layer as discussed above would stop this, though I'm not sure how it would effect your precision.

Also steel and aluminum expand and contract at different rates so if your saw is in an environment with an unstable temperature, you could see the some small amount of warping as one tries to move more than the other that it is rigidly fixed too. 

I think the ridges are actually valleys.  The TS section of the existing fence is powder coated or painted so I shouldn't have to worry about galvanic corrosion, I've experienced that before on my Jeep.  If it started to happen I'd think cleaning and a layer of packaging tape would fix it for quite a while.  Maybe a good time to learn how to anodize aluminum, I've always wanted to try it. 

I can't imagine that the +/- 40 deg. would see that much differential expansion between the two metals.  Can't be any worse than the plastic and steel that is on there now.  If it's too far in either direction of about 70 deg. I'm not going in the shop anyways haha.  Yeah, spoiled CA guy here.  I've got an ac unit to go into the shop and already have a propane heater for the winter. 

  • Like 1
Posted
Just now, xxdabroxx said:

I think the ridges are actually valleys.  The TS section of the existing fence is powder coated or painted so I shouldn't have to worry about galvanic corrosion, I've experienced that before on my Jeep.  If it started to happen I'd think cleaning and a layer of packaging tape would fix it for quite a while.  Maybe a good time to learn how to anodize aluminum, I've always wanted to try it. 

I can't imagine that the +/- 40 deg. would see that much differential expansion between the two metals.  Can't be any worse than the plastic and steel that is on there now.  If it's too far in either direction of about 70 deg. I'm not going in the shop anyways haha.  Yeah, spoiled CA guy here.  I've got an ac unit to go into the shop and already have a propane heater for the winter. 

The risk with the coatings is when you start drilling through them, which damages/removes the coating and becomes the point where you get corrosion. 

Posted

I wouldnt worry about the CTE difference of aluminum and steel. The movement would be greater between the HDPE and steel that comes from the factory. 

Posted

On the Saw Stop the access holes are underneath and a ball-tip hex driver is used.  I found little improvement with the shimmed milled extrusion versus shimming the stock faces and plan to switch back.  Have you tried shimming the UHMW material flush?

SS Fence (2).jpgSS Fence (1).jpg

Posted

I haven't messed with it yet.  I might though, either way I at least have to order a straight edge.  Closest I have is a 4' level which should be close, but not necessarily close enough.  I noticed it as I was making some cuts with my panel sled, the center of the fence seems bowed in some, at least .010"

Posted

You talking about galvanic corrosion?  I really don't think it is that big of an issue, but after seeing white fuzz on the side of my jeep when removing the aluminum rocker guards it is something that I consider.  Jeep sees considerable more vibration, dust, and moisture than the table saw would though.  Big difference being the grit and moisture the Jeep saw.  I also think that larger surface areas would be more prone to the issue. 

 

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 47 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined