Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

maple:binds & smoke... what gives?

Featured Replies

I'm  trying to rip 1"x 2"x 24 " boards out of western maple.   I've bought a brand  new frued 50 tooth combo blade.  I'm feeding it gently.  I've checked my fence alignment.  I've tried toeing the fence out ever so slightly to avoid pinches/binding at the outfeed end. I have a support roller.  but yet.  still binding at times and smoking/burning.   I have a rigid cast iron r 4511 table saw.  I'd really appreciate any thoughts or suggestions...? I've been trying to rip this wood for 3 days now.  getting very frustrated. 

Is it grabbing the splitter so tight it binds? Stress release can cause the trouble you describe. I have had material where I have had to put wedges into the kerf post splitter but, I prefer to move to the bandsaw for difficult material. A lower tooth count blade  could help with the burning.

I get burn marks sometimes when cutting hard woods when this happens I cut the piece 1/16" wider then reset the fence to final width and do a skim cut that should get rid of any burn marks.

  • Author

hi Mike,  

thanks for the input.  I'm on a tight budget right now as I outfitted an entire small woodshop in the last month and was hoping to get away with one combo blade.  but I'm sure a ripping blade would help.  

I created straight edges on the table saw. and checked they are 90 degrees.   don't have room for a jointer in my small shop.  have mitre,  table saw and bench top planer.  that'll have to do me  for now!   

1 minute ago, gee-dub said:

Is it grabbing the splitter so tight it binds? Stress release can cause the trouble you describe. I have had material where I have had to put wedges into the kerf post splitter but, I prefer to move to the bandsaw for difficult material. A lower tooth count blade  could help with the burning.

I have a riving knife in place.  but yes sometimes the wood pinches shut past the knife... so wedging it you think would help?  do you do  this while youre making the cut? 

20170301_160653.jpg

If you get a rip blade, get a thin kerf one. They let you feed the board through a little faster. Maple burns so easily that even when there's no binding a slow rate of feed will burn it.

Thin kerf blades are great but your standard riving knife may be too thick to use with it. And I really like have the riving knife in place for ripping.  Personal preference

Just now, Ronn W said:

Thin kerf blades are great but your standard riving knife may be too thick to use with it. And I really like have the riving knife in place for ripping.  Personal preference

Good point. I personally wouldn't be without a riving knife. Thinner ones are available though.

From the description it sounds like you are getting stress release caused by case handened stock that is causing the kerf to close straight after cutting. Sometimes this happens with wood that has been kiln dried. It's likely that you will see the stock bent like a banana after passing through the tablesaw.

It can be a lot worse with a bandsaw which of course doesn't have a riving knife. I've had case hardened wood that needed wedges driving in after the cut. I kept stopping the bandsaw to drive a wedge in. Kerf closure on a bandsaw blade is normally terminal for the blade.

The best thing you can do is cut the rips wider than you need, leave the timber overnight and then joint it to get it straight again and then pass it through the planer to get it to required width.

  • Author
5 minutes ago, Mike. said:

Do you have the thin strip on the fence side of your cut or the offcut side of your cut?  My guess is you have in on the fence side, because it is easier to set your fence at 2" (or whatever) and rip away.  But you can get some binding that way.

Another option is to set up a little stop block on the offcut side of the blade and use that to register your width.  It is safer if the thin offcuts can fall away from the blade rather than getting trapped between the blade and the fence.  

Here, a picture is worth thousand words.   this is a store bought version but you can also rig up something home made.

http://www.rockler.com/thin-rip-tablesaw-jig

Hi Mike,

I have the thin strip on the offcut side...

fence is on the right feeding the thicker portion of the board through, and I have the 1" offcut side on the left/offcut side. Which if I"m understanding your post correctly is the better way...

That jig looks handy! maybe something to invest in the future.

6 minutes ago, TerryMcK said:

From the description it sounds like you are getting stress release caused by case handened stock that is causing the kerf to close straight after cutting. Sometimes this happens with wood that has been kiln dried. It's likely that you will see the stock bent like a banana after passing through the tablesaw.

It can be a lot worse with a bandsaw which of course doesn't have a riving knife. I've had case hardened wood that needed wedges driving in after the cut. I kept stopping the bandsaw to drive a wedge in. Kerf closure on a bandsaw blade is normally terminal for the blade.

The best thing you can do is cut the rips wider than you need, leave the timber overnight and then joint it to get it straight again and then pass it through the planer to get it to required width.

Thanks Terry,

yes this may be the case, most of the boards are coming out slightly bowed  at each end, kinda like a banana shape...unfortunately I don't have room for a jointer and use the table saw to get straight edges...but maybe I can jerry-rig a makeshift jointer with my 12' planer.

When you feel the wood closing up on the blade, lift it off (one end only), or back it up if you catch it early enough, and go again.  Repeat until you can cut all the way without any binding.   A lot of wood has stress in it.  It's part of the process.

I should note though that I'm a pro who has operated table saws since I was a teenager in the 1960's, and have never operated a table saw with a splitter of pawls on it.  I have never had a kickback because it's second nature for me to feel for the wood binding, and back the board up.   I can't say how many thousands of times I've backed a board up during a cut.  I'm not recommending anyone else operate a saw without at least a splitter on it though.

Also, I never run a board over the table saw or jointer without sighting the edge, and almost never run one through a tablesaw that hasn't first been straightened on the jointer.

@Tom King what is the purpose of backing up the board?  Are you widening the kerf where it has closed?  

  • Popular Post

Rip on the bandsaw instead if you're having binding issues.  Then a pass or two over the jointer.  No potential kickback or burning and your boards will be straight.

I have both 50T and 40T combo blades and I find that the 50T are usually poor at ripping anything thicker than 3/4" thick stock (even with a 3HP cabinet saw).  I'd stick with 40T if you must use a combo.

Also, already mentioned but worth repeating...only cut flat, square stock on the table saw, and those little Ridgids will cooperate better with thin kerf blades.

14 hours ago, Mark J said:

@Tom King what is the purpose of backing up the board?  Are you widening the kerf where it has closed?  

Yes, but the part against the fence should still finish the same width.  If it doesn't, that board has too much stress in it to use for anything anyway.

On 3/2/2017 at 4:53 PM, Ronn W said:

Thin kerf blades are great but your standard riving knife may be too thick to use with it. And I really like have the riving knife in place for ripping.  Personal preference

That raises the question of how to obtain a thin riving knife for use with thin-kerf blades.

I could use that on my R4511, too.

I have run a lot of maple. Burning happens. Use a 24t blade and move through the cut using consistent speed. I always allow extra room to make a skim cut after the rip to clean burn marks. Then off to the jointer to arrive at my final width.

 

-Ace- 

  • Author
1 hour ago, wdwerker said:

MicroJig Splitters has full kerf and thin kerf versions. They work quite well for me. I like the Steel Pro versions a bit better.

excuse my ignorance...I'm new to woodworking.  It seems counter intuitive to me that you need a riving knife to be thinner than your blade, if it's purpose is to prevent the board from pinching after the blade...why is it that you need a riving knife thinner than your blade? to me it seems like a wider one would be more beneficial as it would provide a bigger gap before your wood pinches shut past the blade...I"m sure there's a good reason I just don't know it yet!

Thanks

If the riving knife was thicker than the blade it would stop the cut.

A properly sized riving knife is a few thousandths thinner than the saw blade.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.