Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Four Drawer Dresser / Changing Table

Featured Replies

  • Popular Post

There's a saying that "Life gets in the way".  That has been the story of my life for the last few months; lots of goings on that are outside my normal flow.  This put me a bit behind but, I have finally caught up on a few commissions that were lagging.  This frees me up for my next personal effort for a soon-to-arrive grandchild.  I still think I'll be done before he sucks air but, I'll have to stay focused as I am not a real speed demon.

Its always easiest to start at the beginning; for me that's material selection. 

58f274fcb007f_NikiCTDresser(1).jpg.a5983131c94fcf4ba87b841b5fe3ef05.jpg

I run 6500k lamps for high contrast in the shop.  When I am picking out material I shut those down and fire up some household incandescent bulbs that are in clamp-on fixtures overhead..

58f274fd63b8a_NikiCTDresser(2).jpg.97ba4abb52be41ab794e548c1a6056fe.jpg58f274fdd69cd_NikiCTDresser(3).jpg.6208baca5a19747722c50b42cddc606b.jpg

I've said before that design, material selection and finishing choices are a large part of the things that I make.  Building things is really just a matter of mechanics.  Deciding what you will build and how is where the fun comes in.

I use a jigsaw for breaking lumber down, It's quick, isn't prone to kickback and stores in a slot on one side of a shelf.

58f274fe78471_NikiCTDresser(4).jpg.0fd151856cca8798977d172fb75cf85b.jpg58f274ff1d4e6_NikiCTDresser(5).jpg.1e6fe75730e64e4bfae9dae177f6fc7a.jpg

I have had a piece of cherry standing around for quite a while.  The color, sapwood and a split at one end have caused me to pass it by repeatedly.  If I tickle it just right I may be able to get the four legs out of it.  Its worth a try.  I lay out parts slightly oversized and mount a Woodslicer on the bandsaw.  This narrow kerf blade helps out when I don't have a lot of wiggle room.

58f274ffb3e78_NikiCTDresser(6).jpg.056deb21bbe1284a01a7380a1266689d.jpg

The split gets lost in the spoil and the twist will fall prey to the jointer.  I often just finesse (read manhandle) my way through the 'teeter-totter' effect.  Since I have so little material to spare I want to be a little more  controlled.  I keep a bundle of thin cutoffs near the jointer and use them as a sort of sacrificial shim.  This lets me bear down on the material as if it were flatter than it is.

58f2750047780_NikiCTDresser(7).jpg.3cf856852b8515cd8b3d228e526eef89.jpg58f27500cb9d2_NikiCTDresser(8).jpg.0afb8c51b435886784d58891cf62bfef.jpg58f275016c685_NikiCTDresser(9).jpg.3d600f6e031bee2a1f3275206b7b8f9f.jpg58f27501f3780_NikiCTDresser(10).jpg.ac91260661830bb587d909c19c9273da.jpg

The flattened area didn't show well in the pics so I chalked it just for show.

58f2750296549_NikiCTDresser(11).jpg.eb52b79507cd0f315819cbd430836d48.jpg

At any rate I was able to squeeze the four legs out of it.

58f2750341b51_NikiCTDresser(11.3).jpg.8b2c558b223c91a4706a1d34393bb577.jpg58f27503ca2c5_NikiCTDresser(11.5).jpg.04be98fc25c1d540a73d1c6d1fe98211.jpg

I continue to breakdown previously selected material to get the blanks down to a more manageable size.  They're not getting sanded, that's just the only free flat spot right now.

58f2775d29eaa_NikiCTDresser(12).jpg.59db9489e44eb28dafc8ccc37a9640d3.jpg

The material I have decided on for the top is wider than the jointer so the planer sled gets to come out of the overhead racks for a spell.

58f2775de0397_NikiCTDresser(13).jpg.cd03a44ffb85c258c2b159852976526a.jpg58f2775e71b0c_NikiCTDresser(14).jpg.513ee9b7d5c6e4746bfa664b1e7d59b8.jpg58f2775f27a88_NikiCTDresser(15).jpg.21d1a473952b082aedb2e40839d01de8.jpg

I am using typical frame and panel construction with M&T at the stress points.  The Mortise Pal takes care of quick, accurate, repeatable mortise work.  You can see that I have made my own templates to compliment those that came with it; really easy.

58f2775fdaec1_NikiCTDresser(16).jpg.cfcb48316c138d9c7fc5a02f921b73eb.jpg58f277608d8d5_NikiCTDresser(17).jpg.1a09a1c20ea5f0cba0a5df2eb2728741.jpg58f27761488a6_NikiCTDresser(18).jpg.bac55b789aa8a76ec86a173b546bfb6f.jpg58f27761f017f_NikiCTDresser(19).jpg.aeb12633a82c676927e6d808f9a53dae.jpg

Most of the other joinery comes right off the tablesaw which is a time saver.

58f27762ad22d_NikiCTDresser(20).jpg.47753f1d8df8684e67377947c54a0d54.jpg58f277635d2a1_NikiCTDresser(22).jpg.43ba687bd433c440d2e8498cf6bfd975.jpg

A quick dry fit before proceeding . . .

58f27764112b3_NikiCTDresser(23).jpg.d844ab96564f827e9a6464696f5b418f.jpg

This is where I'm headed . . .

three-quarter.thumb.JPG.d29f699de05b97457d02aeaaec4cb8cc.JPG

I couldn't remember why I took this pic at first.  Maybe because I use a ROS so seldom it was a novelty . . . Oh yeah, I wanted to share the "pipe clamp and bungee as hose and cord boom" method.  Handy if you only do this sort of thing now and then.

58f27764c0ca2_NikiCTDresser(24).jpg.f85823faac85ecc16b30e5694b9c133e.jpg

A discussion of a fairing stick or marking bow came up in another thread.  I had shared my shop made version and here it is in use.

58f2776572597_NikiCTDresser(25).jpg.e693fd3b67aca02e86d50c91ef42ce09.jpg

Another part of that discussion was the difference in long and short stretchers and the arch height for them.  I have mentioned that I keep my arch height consistent regardless of length.  You can see in the next pic the difference in arch to keep the height the same.

58f2776628105_NikiCTDresser(26).jpg.019c0e25b315e2ea5762dda5ccb0686f.jpg

  • Replies 93
  • Views 20.8k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • I rough cut the arches on the bandsaw.  You can smooth these on a spindle sander, using a card scraper or even a shaped piece of scrap and sandpaper.  I generally just take after them with a

  • Got a few pics in a better setting.  It was a bit deeper than the hearth so I used a piece of cherry scrap as a prop. Trying to show off the butterflied raised panels . . . I liked

  • OK, back is on . . . and breadboard detail plugs are done.  I have a couple of plastic shoe boxes that I keep "interesting" scraps in.  I pawed around and found some walnut to use.  I size t

Posted Images

  • Author
  • Popular Post

I rough cut the arches on the bandsaw. 

58f27a0c6a994_NikiCTDresser(27).jpg.3e863067ab2dc7084f572a39d2cda013.jpg

You can smooth these on a spindle sander, using a card scraper or even a shaped piece of scrap and sandpaper.  I generally just take after them with a shave.

58f27a0d24592_NikiCTDresser(28).jpg.a556d213014cd5e18e9e4ee82098bb45.jpg

The frame and panel sides will have two panels each.  I resaw thicker stock to get book-matched pairs.  I layout witness marks and raise the panels with whatever plane feels right at the time.

58f27a0da9a6a_NikiCTDresser(29).jpg.ec42cb8695d5a5bb80fc0de666ffd23c.jpg58f27a0e5a958_NikiCTDresser(30).jpg.018d2d97ac79ee81b9aabda7bf7450f8.jpg

Here's a before and after.

58f27a0f11369_NikiCTDresser(31).jpg.2ad0a62e39c92d41834b11c57ae26575.jpg

I dry fit the ends and move on to the top.

58f27a0fb80b0_NikiCTDresser(32).jpg.25ff6e2d4f633437545cfea99047f4d1.jpg

I picked this up somewhere along the way.  I joint the edges while ganged in the vise.  This way if I am not perfectly perpendicular, it doesn't really matter.

58f27a1064097_NikiCTDresser(33).jpg.927421fcfd92a34d6da834a0d200cdf3.jpg

And the sides and the top go into the clamps.

58f27a11201e4_NikiCTDresser(34).jpg.66e06c1e5c6820d39e4252b8a9ceb32f.jpg

Time for a cup of coffee ;)

Good stuff gd. Nice looking material too.

 

Sent from my SCH-I545 using Tapatalk

 

 

Looking fine sir! I didn't see any arches in the illustration?

  • Author
11 hours ago, K Cooper said:

Looking fine sir! I didn't see any arches in the illustration?

Thanks all.

@K Cooper Here's another angle.  To be fair, the arches are only 1/2" high in the drawing, It was too subtle so I changed this to 3/4" high on the build.

 

arches.thumb.JPG.95485c9aaff90e41851dba4399893a56.JPG

1 hour ago, K Cooper said:

I looked everywhere but down:wacko:

Your wife trained you well.  Her constant instruction was my eyes are up here.

1 minute ago, Woodenskye said:

Your wife trained you well.  Her constant instruction was my eyes are up here.

I wish for the sake of my constantly bruised arm, that always held true:wacko:

  • Author
  • Popular Post

We have friends and relatives coming over for Easter so I have to shut down.  I'm happy now with the top's surface.

58f3c635a83ee_NikiCTDresser(35).jpg.1a089da76fcf44c885e207bb5a9b56e7.jpg

No real magic here; I just use the sled to cut the top to final length.

58f3c636764e7_NikiCTDresser(36).jpg.ff4b1fd344ad7726910515db705e4a7c.jpg

Take a moment to switch to a dado stack.  No need for a throat plate as I will use the sled again.

58f3c63724f5d_NikiCTDresser(37).jpg.168d11fab11324b4b5cb7313ff3bedeb.jpg

I have a variety of inserts for the sleds.  If I remember, I scrawl the last use on the piece so I can get a few uses out of them.

58f3c63819fa8_NikiCTDresser(38).jpg.1f2255c01190b3fea21a1245ec16b687.jpg

I didn't have a fence insert the right size from a previous use but, I make them so they can be flipped so I guess I'll have one next time.

58f3c638d40cd_NikiCTDresser(39).jpg.30590a3070f9639ab057bd17dbcc28df.jpg

And that gives me the tongue for the breadboards.

58f3c639ad578_NikiCTDresser(40).jpg.4a3980a0379cc7a776045bce0f84c3ef.jpg

Someone's knocking, time to go.

  • 2 weeks later...
  • Author
  • Popular Post

Its things like this that keep us humble and honest :unsure:.  My credo in the shop is "There is no shortcut to anywhere I want to go".  In gluing in the upper and lower rear stretchers, the ones that will capture the back-slats, I was doing the assembly on my bench.  This put the piece in an awkward position for the usual and customary 'check for square'.

I did a quick check from an odd reaching angle and although it did not seem quite right, I put it off to the odd reach I was having to make.  Once the glue was set and the clamps came off I realized I had very consistently made the upper adn lower rail 1/2" too short; there's no fixing that in place.

I taped off a narrow path up close to the leg.  This made an easy to follow guide whilst I jig-sawed the offending rails out of the carcass.

58fe85cc34746_NikiCTDresser(41).jpg.48326079c21776a6be4edaa152a16b62.jpg

58fe85cd108c1_NikiCTDresser(42).jpg.03753acbac2f8db4db5f6d93e711f314.jpg

I then used a small router and a flush trim bit to clean up the excess.  Then a slot cutter to remove the old tenon from the slot.  New rails were grooved for the back-slats and had the stub-tenons cut on them.  Amazingly the correct sized parts made the carcass clamp up nice and square.

58fe85cdb426e_NikiCTDresser(43).jpg.7d620f002e656a18a59d88eb15f8c33b.jpg

I moved on to fitting the breadboards and was once again reminded just how nice it is to have the right tool for the job.

58fe85ce9cbdc_NikiCTDresser(44).thumb.JPG.16867799f1a7dbf7a6457b048afda4c8.JPG

58fe85cf6b510_NikiCTDresser(45).jpg.6924a3e37e5f999f068dee73fc051a1c.jpg

To be continued . . .

Great recovery and the breadboard is SWEET! I should order one of those planes rat now!

  • Author
  • Popular Post

Thanks Coop.  Let's just say I've had plenty of practice in recovering from boo-boos :D.  As any who have followed other builds know, I use a Mortise Pal for a lot of things.  There will be some decorative and functional walnut splines covering (or drawing attention to) the breadboard T&G joint.  I find I have good luck making the joint and then cutting the pocket into both pieces at once.

It turns out that I want a slot in a size I don't have a template for.  It just takes a few minutes to make one out of a piece of 1/8" hardboard at the drill press.  I use a commercial template as a . . . er . . . well . .. a template.  I just overlap the Forstner bit holes and touch it up with a file.

58fe9c6539b73_NikiCTDresser(46).jpg.ff9a126f59d5640d7ed7e1bcd186f8e8.jpg

58fe9c6613c87_NikiCTDresser(47).jpg.238cc7f9f41957f38f60e04a4ed1054e.jpg

The point is, when you find yourself thinking "I wish I had a widget that would do blah". Think outside the box.  If you look around I bet you'll find what you need to cobble together a solution.  If it works well, make a better version to keep for next time and share it with us :).

I put the template in the MP, cut the slot and then square the ends with a couple of taps on a chisel.

58fe9c66acf9c_NikiCTDresser(48).jpg.024ca3068bc32683c9f3bba835b72f46.jpg

This feature will be more obvious once I get a little further along but, you can sort of see it in the SketchUp drawing earlier in this thread.  It will be similar to a feature I use on this cabinet.

57d1f9e2bbe18_MediaCabinet(167).jpg.f2e285b5c623263cc0909e9141ca87b9.jpg

In this case the breadboards and top will be flush as there will be a tray affixed to the top until the little guy is out of diapers.

  • Author

Pug asked about a drawer-lock bit in this thread.  I have the Whiteside I mentioned in his thread and so thought I'd show how I use it.  I cut the blanks big enough to do several drawer parts, profile them and then slice them into pieces sized for the drawers.  I find this gives me a better fit than trying to do drawers one at a time.

I already know that for 1/2" BB ply I set the bit to 11/32" high.

590288f6582d0_NikiCTDresser(49).jpg.d0dcb8b73a70947db130abf65cc7629c.jpg

It is easy to get a close thickness on the material like so . . .

590288f733678_NikiCTDresser(50).jpg.622a85370deda528271646c34a75f0d5.jpg

I then set the fence with that dimension.

590288f7d531b_NikiCTDresser(51).jpg.e5c2da86ad616637684ab399f8b5bd77.jpg

Here you can see a "tall" fence I made for such tasks.

590288f8ace8d_NikiCTDresser(52).jpg.f42934a61b3b1c166c0f411f575d89cc.jpg

After cutting the fronts and backs horizontally I move the fence forward 3/8" (for this particular bit) and cut the sides vertically. 

59028a5bc1ccb_NikiCTDresser(54).jpg.1b164353281d748452746fc46ae9cbbd.jpg

And there's your joint.

590288f9a560f_NikiCTDresser(53).thumb.JPG.c523299dc3c2ad9e54757313ba0b9bd5.JPG

Now I just rip the drawer parts off of the larger blanks.

  • Author

I see no sunset . . . I soldier on :).

I have a method (or habit) when using a drawer lock joint made with a router bit.  I make the front and rear pieces 1/16" over-long.  This makes the drawer-lock joint have a proud tongue which I then sand (for plywood) or hand plane flush (for hardwood). 

It is an extra step but, has served me well and I'm not smart enough to stop doing it.  This does require a little caul when clamping so that the pressure is placed on the drawer side and not the proud tongue.  Pieces of scrap wrapped in packing tape work fine.

5906743f54203_NikiCTDresser(57).jpg.be9e80653ce87b1c0054e1c6f69120b8.jpg

5906743e932ca_NikiCTDresser(56).jpg.3e81102dcd5d0d82bd819a59e3eb22e0.jpg

5906743daba1d_NikiCTDresser(55).jpg.83a033ff7f6d075bbac4ee938747cf8b.jpg

I have a couple of coffee cans stashed over by the larger bandsaw just full of little helpers like this.

590674403e6b9_NikiCTDresser(58).jpg.b4cf42f8975db578c5768cb6b282a864.jpg

My preferred method for mounting breadboards when hiding the joinery is to peg them from underneath.  I drill 1/4" holes and turn the middle and rear holes in the tongue into slots.  This keeps the front appearance aligned and lets the top expand toward the rear. 

I want to drill through the underside of the breadboard, through the tongue of the top and part way into the upper portion of the breadboard BUT, not all the way through.

Even though this is not a large top, it is too awkward for the drill press.  To inspire confidence (and to save me from having to make new breadboards), I use a drill with a stop and a guide.  To setup, I place a piece of 1/8" scrap next to the upside down top/breadboard.

5906744128105_NikiCTDresser(59).jpg.f958e63fd98b0ec5213116508f2574d4.jpg

I rest the guide on the surface that I will clamp it to and drop the drill through until it hits the scrap.  I now know that this depth will absolutely not pierce the top of the breadboard.

590674420d2ee_NikiCTDresser(60).jpg.9b099d19360ac1f85a27771777624b42.jpg

I drop the collar on and tighten it.

59067442dafa7_NikiCTDresser(61).jpg.848656f8613ee7ff111f0fd2393869d8.jpg

I use a stubby awl that my dear old dad made for me to dimple the location of the holes which I have previously laid out.

59067443b3408_NikiCTDresser(62).jpg.5733c53364bf725e42dc9a1b32d4102e.jpg

I slip the drill through the guide, use the dimple to locate the point of the bradpoint bit, slip the guide down onto the surface and clamp it in position.  Clamping is just extra security for me.  My shoulder is a little gimpy right now and I don't want to risk just holding the guide with my hand.

I drill the hole, move the whole procedure to the next hole and the next, etc.  The result is 3 holes for each breadboard; though the tongue and partway into the breadboard.

5906744491fbe_NikiCTDresser(63).jpg.fe84143d47941bf6dc4770dc55d6ff05.jpg

Now I just setup to "slot" the holes in the tongue and I can move on to some pre-finishing.

 

  • Author

Thanks treeslayer.  I realized I kinda stopped at an odd point.  Here's the slotting method; I layout the starting and stopping points for the slots.  I start by eye but, use a clamp to help me stop consistently as I make a couple of passes to cut through.

59067be0ba9c1_NikiCTDresser(64).jpg.bc7249ba4329a2843cabe2fff4769a12.jpg

59067be19e53c_NikiCTDresser(65).jpg.516c283a308403731da55fa3b421cffa.jpg

This is the guide I pointed out when someone asked about them a few days ago. Don't recall the thread or I would link it.  At any rate, 1/4" hole at the front (from the original drilling), a slot at the middle and a little longer slot at the back.

59067be26338c_NikiCTDresser(66).jpg.07e681b059a5bd09218a8d7cb44a423f.jpg

Now off to do some pre-finishing.

 

  • Author

Got a little distracted and failed to take pics of some of these steps . . .

Got the drawer dividers in and the "show" trim for those dividers in the clamps.

590e3ffe156b2_NikiCTDresser(67).jpg.0045ae0cb283865b534a51248b838409.jpg

Our new member 'kyokahn' coined the term "Drawer Jenga" in this thread.  Cracked me up so I'm stealing it . . .

Drawer Jenga!

590e3ffee5a9e_NikiCTDresser(68).jpg.408832502d0dcddebd51e3703032a9e5.jpg

As shown earlier, the breadboard ends are pinned through a fixed hole at the front and slots in the middle and rear.  This keeps things aligned at the 'show' side and lets things expand at the rear.  Other details on this piece will be walnut for contrast so I will pin the breadboards with walnut doweling (not that anyone will notice them under there but, I have a twisted sense of humor or something).

590e3fffa178f_NikiCTDresser(69).jpg.9028e33d9c550e0a890c96c48356aa8c.jpg

If you watch the usual supply houses you can get this little miter and saw for about $20 on sale.  I've been using this one for about 3 years so I certainly got my money out of it.  When it goes dull I'll just toss it and open one of the two replacement saws I picked up as an unexpected bargain-bin bonus at Rockler.

590e40008538a_NikiCTDresser(70).jpg.48f9d65b9ed6308e5d0ad5579566e636.jpg

In just a few strokes I have the dowel pieces I need.

590e400165758_NikiCTDresser(71).jpg.d5b494c8c0b2df349ba254fe3bbd27a7.jpg

I apply glue to a couple of inches at the front of the breadboard, chamfer the leading edge of the dowel and drive it home.  For the other positions I put a drop of glue in the hole, shooting for the stopped-hole end that receives the dowel and drive the other dowels in.

590e4002460aa_NikiCTDresser(72).jpg.c3f6a2c58f145936194b8d0ebdf9de40.jpg

I'll pare these flush later.

590e40031a48a_NikiCTDresser(73).jpg.daa79f6e1c8c01faea813ac323bf48bd.jpg

I leave the top in the clamps and go in search of drawer front material.

590e4004003df_NikiCTDresser(74).jpg.b26db1d44fa122b847b2c7ad893a0bae.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.