freedhardwoods Posted April 19, 2017 Report Posted April 19, 2017 After discovering how lousy my homemade router table is to use, I'm going to start over. I'm seriously thinking about getting Sommerfelds router table top and fence, but I could change my mind if I see something better. Can some of you show and/or tell me what your setup is? Good and bad points? Quote
wtnhighlander Posted April 19, 2017 Report Posted April 19, 2017 Sorry, still home made for me. I don't know what I'm missing! Quote
RichardA Posted April 19, 2017 Report Posted April 19, 2017 Ditto, what Ross said. But I'm looking. 1 Quote
CandorLush Posted April 19, 2017 Report Posted April 19, 2017 I have this setup and really enjoy it, I started with just the table and fence and added the lift later. I had a freebie 42" wide base cabinet with a 48" laminate countertop that I routed out to inset the entire table into 2 Quote
Eric. Posted April 19, 2017 Report Posted April 19, 2017 http://www.incra.com/tables_stands-free_standing_table_tops.html 2 Quote
Popular Post gee-dub Posted April 19, 2017 Popular Post Report Posted April 19, 2017 Commercial top (found on clearance before I started to make my own) and built my own base. If you don't have to customize your top to fit the lift or plate style you go with, all the better (I did but, it was on clearance ). In my experience the fence is the focal point regardless of how simple or complex. I do prefer through slots for the fence as opposed to tracks which can become fouled with spoil. Side mounting fence rails avoid this also. Many composite tops can be made flat if they are mounted to a good supporting structure as long as they are consistent in thickness. My point is that although cast iron is nice, it is not always flat and is more costly than some alternatives. I hesitate to recommend specifics since I have done well for years on a melamine skinned MDF top whereas some folks can have issues with anything shy of a cast iron top. Look at your needs for size and wear-factor, fence options and lift or plate type. This will shorten the "top" list quickly if you go commercial. 3 Quote
Woodenskye Posted April 19, 2017 Report Posted April 19, 2017 I went with a commercial top from Rockler and then I decided to get a cast iron router wing for the table saw. I'm actually thinking of using the old commercial 1 as part of the extension table. Just not sure this makes any sense, plus I would need a new plate. Does 2 router tables make any sense? Quote
Eric Anderson Posted April 19, 2017 Report Posted April 19, 2017 I went with the bulldog cast iron table top, woodpecker lift and Jess'em fence (and home-made "Norm" inspired router table body. Cost a fortune and could have purchased a low end shaper for same money, but it works like a dream, with excellent dust collection (I have fence collection and unbeatable collection). Maybe not for everyone, but table is large 24x32 and won't sag. Quote
Eric. Posted April 19, 2017 Report Posted April 19, 2017 15 minutes ago, Eric Anderson said: I went with the bulldog cast iron table top, woodpecker lift and Jess'em fence (and home-made "Norm" inspired router table body. Sounds like a killer setup. I was gonna buy one of those Bulldog tables before I decided to buy the Incra system. Not sure I'd make the same decisions now...either the cast iron or the Incra. Nothing like a decade of building projects to really find out what you need and what you don't need...but how do you know until you own the overkill version of something? I love the micro-adjust on the Incra fence...but that's just about the only feature I use with any regularity...and that one feature surely isn't worth the huge pile of money I dropped on it. Oh well, I'll never have to buy another one. 1 Quote
krtwood Posted April 20, 2017 Report Posted April 20, 2017 I have the big cast iron top as well. If I had it to do over again, I think I would make a triangular setup with three routers, or two routers with a fence that comes to a point in the middle. I don't really do much with big bits and cope and stick type stuff that would benefit from what I have but I sure swap between a roundover and a 1/4" spiral a lot. Those could be in trim routers that would cost less with a shop made top than the cast iron beast. Quote
jplemons Posted April 20, 2017 Report Posted April 20, 2017 I have an Incra setup and really like it. Can't beat the micro adjust for accuracy. Quote
Ronn W Posted April 20, 2017 Report Posted April 20, 2017 My setup is totally home made except for the insert and fence. Base cabinets with 2 layers iof 3/4" MDF. Insert is a Kreg and the fence, not shown, is a woodpecker. I must admit that the insert is not perfectly flush with the top of the MDF but it is damn close. Works well for me. Sorry about the sander in the pic. Quote
mikem Posted April 20, 2017 Report Posted April 20, 2017 My router table is shop made. 2 layers of 3/4" MDF, 3/4" hardwood (maple is what I had lying around) edge banded, Made sure edge banding was flush with mdf top, then added white formica on the top, and flush trimmed, then ran a decent size chamfer around the perimeter. Then used a template jig to route out for the insert. I also routed out a groove for the woodpecker combination t-track/miter slot bar. Both the fence and the cabinet it sits on have been ducted for dust collection. I have had this setup running for a couple years now, and I love it. Quote
freedhardwoods Posted April 21, 2017 Author Report Posted April 21, 2017 Lots of good info to think about. I'm looking at and considering the tables and fences that several of you mentioned. My router table will get about as much use as my table saw. Thanks everyone for the info and pics. Quote
freedhardwoods Posted April 21, 2017 Author Report Posted April 21, 2017 You guys with the homemade tops have some nice setups. In other circumstances, I might try the homemade route again. I have people waiting for me to get started and getting a good metal top is the quickest way to get me building cabinets instead of tools. On 4/19/2017 at 2:39 PM, Eric Anderson said: I went with the bulldog cast iron table top, woodpecker lift and Jess'em fence (and home-made "Norm" inspired router table body. Cost a fortune and could have purchased a low end shaper for same money, but it works like a dream, with excellent dust collection (I have fence collection and unbeatable collection). Maybe not for everyone, but table is large 24x32 and won't sag. Is this the table and fence you have? I can't find Bulldog brand, but Bench Dog has a bulldog in their logo. This could be very close to the top of my short list. http://www.benchdog.com/ProMax-RT http://www.jessemdirect.com/product_p/04010.htm Quote
freedhardwoods Posted April 21, 2017 Author Report Posted April 21, 2017 I spent all morning looking at and studying several tables and fences. I finally settled on the Sommerfeld table and fence. It is designed to do what I will be using it for. If I start doing other projects that the Sommerfeld combo isn't as well suited for, I may get the Bench Dog table and Woodpecker or Incra LS Super fence. Thanks again for all the info and pics. Quote
Eric Anderson Posted April 25, 2017 Report Posted April 25, 2017 Free, Yes, bench dog, not bull dog. I had just got back to the US after a two day flight from Morocco, so was a little jet lagged and out of it. You have the top and the fence I used correct. You will need to make some small mods to the fence to use the Jessem but they are easy. You don't need the rails that come with the fence, Just use the handles and the grooves in the table top along with a couple of tee-slot nuts and you are good to go. I think this actually works better than Jessem intended with their original design. The one drawback with the bench dog, is it only fits the bench dog lift or the woodpecker lift (they have a special sized lift for the bench dog), It is I think 8 1/4" x 11 3/4" instead of 9 1/4" x 11 3/4". But I really like the woodpecker lift anyway, so I'm fine. Good luck. It is a nice set up and will last forever. Quote
ben_r_ Posted April 25, 2017 Report Posted April 25, 2017 Ive got the Benchdog cast iron top, Rockler steel dust collection box below it and the Incra lift with the magnetic CleanSweep inserts. LOVE the setup, highly recommend it. Quote
Immortan D Posted April 25, 2017 Report Posted April 25, 2017 I have the Woodpeckers router plate, Incra fence and DIY "portable" table top with an extension. I only attach the extension and the fence when I need it. Video: I added a t-track later on. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.