Ronn W Posted June 12, 2017 Report Posted June 12, 2017 I just got a catalog from MCLS (mclswoodworking,com)/ They have a lot of router bits on sale including a set if 5 flush tirm, pattern and double bearing bits on sale for $69.95. These are not just the smaller diameters. Does anyone have an opinion regarding the quality of their router bits? Quote
AceHoleInOne Posted June 12, 2017 Report Posted June 12, 2017 I have purchased from them in the past. The quality is ok. I think they're "offshore" quality. I like woodline router bits, better price point. (disclaimer ~I haven't purchased any bits in the past 3 years......so let the buyer beware ) -Ace- Quote
gee-dub Posted June 12, 2017 Report Posted June 12, 2017 I use them for a profile I want to try out cheap. They don't hold up like a Whiteside or a Freud so your intended use will dictate whether the price is a good deal or not. Quote
gee-dub Posted June 12, 2017 Report Posted June 12, 2017 I haven't seen anything more recent but, Wood's test pretty much matches my experience. Here's a snip. 1 Quote
BonPacific Posted June 12, 2017 Report Posted June 12, 2017 I'm with the others. They're serviceable, but nothing special. I have a big variety kit from them, since I wanted to have options available without having to order something new if I want to try it out. Quote
pkinneb Posted June 12, 2017 Report Posted June 12, 2017 I have a couple but prefer Whiteside and Freud quad cutters where available. Quote
Ronn W Posted June 12, 2017 Author Report Posted June 12, 2017 That's kinda what I expected. Thanks guys. Quote
bleedinblue Posted June 12, 2017 Report Posted June 12, 2017 I have one of their bigger boxed sets but haven't had it for long. I figure that any of those bits that I wear out are used enough to replace with Whitesides. Quote
Tom King Posted June 12, 2017 Report Posted June 12, 2017 I bought one once. It lasted a few minutes. That one was replaced by a Whiteside bit like it. I still have the Whiteside bit. On the chart in gee-dub's post, the Eagle America bits awarded, are made by Whiteside. That might tell you something. 1 Quote
wdwerker Posted June 13, 2017 Report Posted June 13, 2017 I got several of the MCLS bits and a few Woodsides when I bought a router table at an estate sale. The guy threw in all the bits. Lots of burned up bearings and bits gummed up with resin. Replaced the bearings, cleaned the bits and they aren't bad but definitely not as good as the Whiteside, Freud and Amana bits I usually buy. However it is nice to have some extra profiles and multiples of common bits. Quote
knotscott Posted June 13, 2017 Report Posted June 13, 2017 They used to be decent bargain bits, but have heard from other respected woodworkers that the quality has slipped in recent years. Since I have bought any new in more than ten years, I can't say from first hand experience what the new ones are like. They never were in the league of Whiteside or Infinity....or even their own Katana line for that matter. Quote
ben_r_ Posted June 14, 2017 Report Posted June 14, 2017 I say skip em, buy Whiteside, buy from Hartville Tool, use the code "wn15" for 15% off, and get free shipping any order and no tax for most. 1 Quote
pkinneb Posted June 15, 2017 Report Posted June 15, 2017 2 hours ago, ben_r_ said: I say skip em, buy Whiteside, buy from Hartville Tool, use the code "wn15" for 15% off, and get free shipping any order and no tax for most. Good to know now that Amazon has started charging tax. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.