Popular Post Chris208 Posted June 13, 2017 Popular Post Report Posted June 13, 2017 Hi, Ya'll I bought the lumber for this thing in May 2015. A guy a few towns over was clearing out the contents of his deceased father's barn, and was selling this on CL as "Maple Beams." This is a very soft maple. I ended up getting about 250 board feet of 16/4, 12/4, and 8/4 for $200. I used the 12/4 and 16/4 for this bench, and 12/4 and 8/4 for a bed I built my daughter. The bench is 8'5" long, and 33.5 inches tall. The bench top ended up being a hair under 3.5" after flattening. I went with the Benchcrafted leg vise, and omitted a tail vise due to cost. I plan on getting a Veritas bench pup to help in that area. I'm already seeing how useful it would be. I did an offset split top, with the front slab being wider than the back slab. I also did my gap-stop differently, adding a reversible tool tray. I can flip it over, and have it flush with the bench top. It's not very wide, so only smaller items fit in there, but I've found it useful so far. It does collect chips like crazy though. Not a big enough bother to flip over permanently. It took me 23 months from start to finish, with several projects in between, but it's done, and I love it! I've got about $600 in this bench including the vise hardware and Gramercy Holdfasts. Chris Far, far from perfect, but it's flat, it's heavy, and it holds work. A close look reveals extensive tearout and tool marks. That's built-in character, and frankly, I needed to just be done with this thing. 10 Quote
Eric. Posted June 13, 2017 Report Posted June 13, 2017 Cool bench. You're missing out on half the functionality without a tail vise though...you may grow to regret that decision. 1 Quote
Chet Posted June 13, 2017 Report Posted June 13, 2017 2 hours ago, Chris208 said: Veritas bench pup to help in that area You might want to consider the Veritas inset vise also. The bench does look nice. Quote
Chris208 Posted June 13, 2017 Author Report Posted June 13, 2017 28 minutes ago, Chet K said: You might want to consider the Veritas inset vise also. The bench does look nice. I saw the inset vise. I'm resisting it because a: it's ugly, and B: I saw a review that said it had gotten loose/sloppy after a couple years. I don't want to dig a big ass hole in my bench for something that's a temporary solution. If the bench pup doesn't do what I need, I'll retrofit the BC vise. Not much more work than installing it while I was building, because the tops are slabs. Thanks! 2 Quote
..Kev Posted June 13, 2017 Report Posted June 13, 2017 The HNT Gordon tail vise would be an easy drop in there as well. Nice job on the bench! 1 Quote
Brendon_t Posted June 13, 2017 Report Posted June 13, 2017 Geesh. After 22 months without finishing, I would have burned it to the ground. Glad you didn't. Quote
Pondhockey Posted June 13, 2017 Report Posted June 13, 2017 And even some natural light. Good job. Quote
Chris208 Posted June 13, 2017 Author Report Posted June 13, 2017 46 minutes ago, TIODS said: The HNT Gordon tail vise would be an easy drop in there as well. Nice job on the bench! This is intriguing. Never seen it before. It would certainly fix my ugly concern, and looks really well built. Thank you for showing me this. 1 Quote
..Kev Posted June 13, 2017 Report Posted June 13, 2017 15 minutes ago, Chris208 said: This is intriguing. Never seen it before. It would certainly fix my ugly concern, and looks really well built. Thank you for showing me this. I really like mine. Pretty easy to install as well. I shot some video of it in my OF table thread in the journal section. 1 Quote
ClassAct Posted June 19, 2017 Report Posted June 19, 2017 Beautiful! If you ever decide you don't need it anymore, let me know.... Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.